Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2013.08–2014.11
RM2070E _58 Vehicle Interior _061940 METER / GAUGE / DISPLAY _0301792 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speedometer Malfunction  


DESCRIPTION

The combination meter sub-assembly receives the vehicle speed signal from the skid control ECU via the CAN communication system. The speed sensors detect the wheel speed and send signals to the skid control ECU. The skid control ECU supplies power to the vehicle speed sensors. The skid control ECU creates the vehicle speed signal based on the pulses of the voltage.

HINT:
·

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using the GTS. For details about testing and the margin of error, see the reference chart (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).

·

If the vehicle speed sensor circuit has a malfunction, the skid control ECU stores DTCs. Troubleshoot the brake control system (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).



WIRING DIAGRAM

E337681E14
0.26,3.104 1.865,3.635 1.604,0.531 10 false Skid Control ECU 2.938,3.177 4.792,3.604 1.854,0.427 10 false : CAN Communication Line 5,3.104 7.073,3.656 2.073,0.552 10 false Combination Meter Sub-assembly (Meter Circuit Plate)

CAUTION / NOTICE / HINT

NOTICE:

If the vehicle speed is outside the allowable range when tested, perform the on-vehicle inspection (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).


HINT:

Before starting the following inspection, check the tire size and tire air pressure.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).

Result:
Result Proceed to
CAN communication DTCs are not output. A
CAN communication DTCs are output. B




A

2.PERFORM ACTIVE TEST USING GTS (SPEED METER OPERATION)

B

2.PERFORM ACTIVE TEST USING GTS (SPEED METER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Check the operation by referring to the table below.

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Speed Meter Operation Speedometer 0, 40, 80, 120, 160 mph*1 -
0, 40, 80, 120, 160 km/h*2

*1: with mph units

*2: with km/h units


OK:

Speedometer indication is normal.




OK

3.CHECK ELECTRONICALLY CONTROLLED BRAKE SYSTEM

NG

3.CHECK ELECTRONICALLY CONTROLLED BRAKE SYSTEM
a.

Check if the electronically controlled brake system outputs DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

4.READ VALUE USING GTS (VEHICLE SPEED, VEHICLE SPEED METER)

B

4.READ VALUE USING GTS (VEHICLE SPEED, VEHICLE SPEED METER)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus:

i.

for ABS/VSC/TRAC: Chassis / ABS/VSC/TRAC / Data List.


ii.

for Combination Meter: Body Electrical / Combination Meter / Data List.



e.

Check the values by referring to the table below.

ABS/VSC/TRAC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Maximum wheel speed sensor/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Meter Vehicle speed/Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Almost the same as actual vehicle speed -

Result:
Result Proceed to
The data list values of the ECUs match. A
The data list values of the ECUs do not match. B


HINT:
·

When the Data List values of the ECUs match, an internal malfunction of the combination meter sub-assembly is suspected.

·

When the Data List values of the ECUs do not match, a signal output error of the skid control ECU or an internal malfunction of the combination meter sub-assembly is suspected.





A

B

5.REPLACE METER CIRCUIT PLATE
5.REPLACE METER CIRCUIT PLATE
a.

Replace the meter circuit plate with a new or a known good one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>DISASSEMBLY).

OK:

The operation of the speedometer returns to normal.


Result:
Result Proceed to
DTCs are not output. A
DTCs are output (for LHD). B
DTCs are output (for RHD). C




A

END

B

C