Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › from 2016.05
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301768 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG)  


DESCRIPTION

When the power switch is pushed with the key in the cabin, the certification ECU (smart key ECU assembly) receives signals to switch the power source mode.

Use this troubleshooting procedure when the power source mode does not change to on (IG) but does change to on (ACC).

HINT:
·

When the certification ECU (smart key ECU assembly) is replaced with a new one and the cable is connected to the negative (-) auxiliary battery terminal, the power source mode changes to on (IG).

·

When the auxiliary battery cable is disconnected and reconnected, the power source returns to the mode it was in before the auxiliary battery cable was disconnected.



CAUTION / NOTICE / HINT

NOTICE:
·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>DIAGNOSTIC TROUBLE CODE CHART).

·

The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

If the entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After completing repairs, confirm that the problem does not occur.



HINT:
Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power source mode does not change to on (IG) but does change to on (ACC)
Power Source Control
·

Power Supply Condition

·

IG1 Relay Monitor (Inside)

·

IG2 Relay Monitor (Inside)

·

IG1 Relay Monitor (Outside)

·

IG2 Relay Monitor (Outside)

·

IG1 Circuit

·

IG2 Circuit


-


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 2 INTEGRATION RELAY)
a.

Disconnect the L195 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 1A No. 2 integration relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L195-9 (IG2D) - 1A-2 Always Below 1 Ω
1A-3 - Body ground Always Below 1 Ω
L195-9 (IG2D) or 1A-2 - Body ground Always 10 kΩ or higher




OK

2.INSPECT NO. 2 INTEGRATION RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT NO. 2 INTEGRATION RELAY
a.

Remove the No. 2 integration relay.


b.

Inspect the No. 2 integration relay.



OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the L197 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 2B instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L197-6 (IG1D) - 2B-25 Always Below 1 Ω
2B-6 - Body ground Always Below 1 Ω
L197-6 (IG1D) or 2B-25 - Body ground Always 10 kΩ or higher




OK

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 1, IG1 NO. 2 AND IG1 NO. 3 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 1, IG1 NO. 2 AND IG1 NO. 3 RELAY)
a.

Remove the instrument panel junction block assembly.


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

U190981E02
1.385,0.208 1.698,0.406 0.313,0.198 10 false 2B 5.323,0.208 5.635,0.406 0.313,0.198 10 false 2A 2.865,1.823 3.177,2.021 0.313,0.198 10 false 2E 2.885,2.26 3.198,2.458 0.313,0.198 10 false 2F 3.177,1.813 3.49,2.01 0.313,0.198 10 false *A 3.167,2.26 3.479,2.458 0.313,0.198 10 false *B

Text in Illustration
*A for LHD *B for RHD
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

Measure the resistance according to the value(s) the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
·

2E-1 - 2A-19 (IG1 NO. 1 relay)

·

2E-1 - 2A-11 (IG1 NO. 2 relay)


Auxiliary battery voltage not applied between terminals 2B-25 - 2B-6 10 kΩ or higher
Auxiliary battery voltage applied between terminals 2B-25 - 2B-6 Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
·

2F-1 - 2A-19 (IG1 NO. 1 relay)

·

2F-1 - 2A-11 (IG1 NO. 2 relay)


Auxiliary battery voltage not applied between terminals 2B-25 - 2B-6 10 kΩ or higher
Auxiliary battery voltage applied between terminals 2B-25 - 2B-6 Below 1 Ω




OK

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the L195 and L197 certification ECU (smart key ECU assembly) connectors.

U190840E02
4.385,1.625 4.125,2.292 true 1.979,1.74 1.76,2.292 true 0.302,0.292 0.49,0.448 0.188,0.156 10 false *a 4.781,0.938 5.219,1.094 0.438,0.156 10 false L197 2.156,0.927 2.563,1.083 0.406,0.156 10 false L195 3.927,2.313 4.292,2.469 0.365,0.156 10 false IG1D 1.531,2.313 1.896,2.469 0.365,0.156 10 false IG2D


Text in Illustration
*a Component without harness connected
(to Certification ECU (Smart Key ECU Assembly))
- -

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L195-9 (IG2D) - Body ground Power switch on (ACC) → Power switch on (IG) 1 V or less → 9 V or higher
L197-6 (IG1D) - Body ground Power switch on (ACC) → Power switch on (IG) 1 V or less → 9 V or higher




OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)