When the key is in the vehicle and the power switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.
When the certification ECU (smart key ECU assembly) is replaced with a new one and the cable is connected to the negative (-) auxiliary battery terminal, the power source mode changes to on (IG).
When the auxiliary battery cable is disconnected and reconnected, the power source returns to the mode it was in before the auxiliary battery cable was disconnected.
Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>DTC CHECK / CLEAR).
The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).
If the entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
After completing repairs, confirm that the problem does not occur.
| Problem Symptom | Data List Item | Active Test Item |
|---|---|---|
| Power source mode does not change to on (IG) or on (ACC) | Power Source Control
·
Start Switch1 ·
Start Switch2 ·
Power Supply Condition ·
IG1 Relay Monitor(Inside) ·
IG2 Relay Monitor(Inside) ·
IG1 Relay Monitor(Outside) ·
IG2 Relay Monitor(Outside) ·
Latch Circuit ·
ACC Relay Monitor ·
Key Certif Wait T-Out |
- |
Check the wireless door lock function by operating the electrical key transmitter sub-assembly (See pgeVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).
Wireless door lock function operates.
OK
NG
OK
NG
OK
NG
Remove the transmitter battery from the electrical key transmitter sub-assembly (See pageVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY>REPLACEMENT).
With the brake pedal depressed, hold the electrical key transmitter sub-assembly near the power switch and check if the power source mode changes.
The power source mode changes.
If the power source mode changes, the cabin verification is malfunctioning.
| Result | Proceed to |
|---|---|
| The power source mode does not change | A |
| The power source mode changes. | B |
| *1 | Power Switch |
| *2 | Electrical Key Transmitter Sub-assembly |
A
B
Connect the Techstream to the DLC3.
Turn the Techstream on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light Switch1 | State of brake pedal | ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
·
Use this item to determine whether the stop light switch is malfunctioning ·
The hybrid control system cannot be started when this item is OFF. ·
When this item is malfunctioning , the hybrid control system can be started by pressing and holding the power switch for a certain period of time. |
The Techstream display changes correctly in response to the brake pedal operation.
OK
NG
Read the Data List according to the display on the Techstream.
With the power switch off and brake pedal depressed, hold the electrical key transmitter sub-assembly near the power switch for 2 seconds or more and read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Power Supply Condition | Power supply state | IG2 ON, ST ON, All OFF, IG1 ON or ACC ON | All OFF: Power switch off (ACC and IG)
ACC ON: Power switch on (ACC) IG1 ON: Power switch on (IG) (IG1 relay on) IG2 ON: Power switch on (IG) (IG2 relay on) ST ON: Sending hybrid control system start request signal |
Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time). |
IG2 ON is displayed on the Techstream screen.
If the smart entry and start system (for Start Function) has been canceled on the customization menu, ACC ON is displayed on the Techstream screen.
OK
NG
Read the Data List according to the display on the Techstream.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Power Supply Condition | State of power supply | IG2 ON, ST ON, All OFF, IG1 ON or ACC ON | All OFF: Power switch off (power supply off)
ACC ON: Power switch on (ACC) (ACC relay on) IG1 ON: Power switch on (IG) (IG1 relay on) IG2 ON: Power switch on (IG) (IG2 relay on) ST ON: Starting hybrid control systeml |
Since IG1 ON and IG2 ON turn "on" at approximately the same time, IG1 ON may not be displayed (IG1 ON turns on for a very short time). |
Measure the voltage while reading the Data List on the Techstream.
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L197-6 (IG1D) - Body ground | Power switch off | 1 V or less |
| Power switch on (ACC) | 1 V or less | |
| Power switch on (IG) | 9 V or higher | |
| L195-9 (IG2D) - Body ground | Power switch off | 1 V or less |
| Power switch on (ACC) | 1 V or less | |
| Power switch on (IG) | 9 V or higher | |
| EL197-4 (ACCD) - Body ground | Power switch off | 1 V or less |
| Power switch on (IG) | 8.5 V or higher | |
| Power switch on (ACC) | 8.5 V or higher |
OK
NG
Enter the following menus: Body Electrical / Smart Key / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| The following DTCs are not output:
·
B2785 ·
B2784 ·
B278A |
A |
| The following DTCs are output:
·
B2784 ·
B278A |
B |
| The following DTCs are not output:
·
B2785 |
C |
A
B
C
OK
NG
OK
NG
Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION).
OK
NG
Connect the Techstream to the DLC3.
Turn the Techstream on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
Read the Data List according to the display on the Techstream.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Start Switch1 | Power switch 1 status | ON or OFF | ON: Power switch pressed
OFF: Power switch not pressed |
·
If the power switch is pressed for a short time, the display may not change. ·
Use this item to determine whether the power switch input signal is malfunctioning |
| Start Switch2 | Power switch 2 status | ON or OFF | ON: Power switch pressed
OFF: Power switch not pressed |
·
Backup for power switch 1. However, when the power switch is pressed and held, the control functions only when both power switch 1 and 2 are normal. ·
Behaves the same way as power switch 1. |
The Techstream display changes correctly in response to the power switch operation.
OK
NG
Remove the power switch.
Inspect the power switch.
OK
NG
Disconnect the L197 certification ECU (smart key ECU assembly) connector.
Disconnect the L194 power switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L197-28 (SSW1) - L194-5 (SS1) | Always | Below 1 Ω |
| L197-30 (SSW2) - L194-1 (SS2) | Always | Below 1 Ω |
| L197-28 (SSW1) or L194-5 (SS1) - Body ground | Always | 10 kΩ or higher |
| L197-30 (SSW2) or L194-1 (SS2) - Body ground | Always | 10 kΩ or higher |
OK
NG