Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › from 2016.05
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301768 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (READY)  


DESCRIPTION

When the electronic key is in the cabin and the power switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. In addition, when the power switch is pressed with park (P) selected and the brake pedal depressed, the hybrid system turns on (READY).

HINT:
·

When the certification ECU (smart key ECU assembly) is replaced with a new one and the cable is connected to the negative (-) auxiliary battery terminal, the power source mode changes to on (IG).

·

When the auxiliary battery cable is disconnected and reconnected, the power source returns to the mode it was in before the auxiliary battery cable was disconnected.



CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

If the entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS).

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

Before replacing the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU) or transmission control ECU, refer to the Service Bulletin.

·

After completing repairs, confirm that the problem does not occur.



HINT:
Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power Source Mode does not Change to ON (READY)
Power Source Control
·

Stop Light Switch1

·

Power Supply Condition

·

IG1 Relay Monitor (Inside)

·

IG2 Relay Monitor (Inside)

·

IG1 Relay Monitor (Outside)

·

IG2 Relay Monitor (Outside)

·

Latch Circuit

·

Starter Request Signal


Entry&Start
·

S Code Check

·

L Code Check

·

Engine Start Request

·

Immobiliser


-


PROCEDURE

1.CHECK HYBRID SYSTEM READY ON
a.

Place the electrical key transmitter sub-assembly (key) on the driver seat.


b.

Depress the brake pedal.


c.

Check that the power switch indicator light is green. Then press the power switch to check if the hybrid system turns on (READY).

OK:

Power source mode becomes on (READY).




OK

NG

2.CHECK AUXILIARY BATTERY
2.CHECK AUXILIARY BATTERY
a.

Measure the auxiliary battery voltage with the power switch off.

Standard Voltage:

11 to 14 V


HINT:
·

It may be possible to tell whether the auxiliary battery is discharged by operating the horn.

·

If the auxiliary battery voltage is less than 11 V, recharge or replace it.





NEXT

3.CHECK FOR DTC (ALL)
3.CHECK FOR DTC (ALL)
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


f.

Enter the following menus: Body Electrical / Power Source Control / Trouble Codes.


g.

Check for DTCs.

Result:
Result Proceed to
DTC is not output A
Hybrid control system DTC is output B
Entry and start system (for start function) DTC is output C




OK

4.CHECK POWER SWITCH CONDITION

NG

4.CHECK POWER SWITCH CONDITION
a.

Check the power source mode change.

i.

When the key is inside the vehicle and the park (P) is selected, check that pressing the power switch causes the power source mode to change.

Result:
Result Proceed to
off → on (ACC) → on (IG) → off A
Power source mode does not change to on (IG and ACC) B
Power source mode does not change to on (IG) C
Power source mode does not change to on (ACC) D





A

5.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)

B

C

D

5.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)
a.

Connect the Techstream to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

Read the Data List according to the display on the GTS.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal/OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
·

Use this item to determine whether the stop light switch is malfunctioning.

·

The hybrid control system cannot be started when this item is "OFF".

·

When this item is malfunctioning, the hybrid control system can be started by pressing and holding the power switch for a certain period of time.



OK:

ON (brake pedal is depressed) and OFF (brake pedal is released) appear on the screen.




OK

6.READ VALUE USING GTS (L CODE)

NG

14.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SOURCE AND BODY GROUND)
6.READ VALUE USING GTS (L CODE)
a.

Enter the following menus: Body Electrical / Entry&Start / Data List.


b.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
L Code Check Verification result between ID code box and transmission control ECU assembly/OK or NG OK: Verification result normal
NG: Verification result abnormal
When a malfunction is present:
·

The ID code for the ID code box or transmission control ECU assembly is not registered or the ID code box or transmission control ECU assembly is malfunctioning.

·

The gearshift control cannot be locked.

·

The gearshift control cannot be unlocked (the hybrid control system cannot be started).



OK:

OK appears on the screen.




OK

7.READ VALUE USING GTS (ENGINE START CONDITION)

NG

12.REPLACE TRANSMISSION CONTROL ECU ASSEMBLY
7.READ VALUE USING GTS (ENGINE START CONDITION)
a.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Engine Start Request Reception state of hybrid control system start permission signal determined by ID code box and sent to certification ECU (smart key ECU assembly)/OK or NG OK: Receiving signal
NG: Not receiving signal
·

When this item displays "OK", the certification ECU (smart key ECU assembly) has received hybrid system start request signal from the ID code box and has permitted hybrid control system start.

·

The hybrid control system cannot be started when this item displays "NG".



OK:

OK appears on the screen.




OK

8.READ VALUE USING GTS (S CODE)

NG

12.REPLACE TRANSMISSION CONTROL ECU ASSEMBLY
8.READ VALUE USING GTS (S CODE)
a.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
S Code Check Verification result between certification ECU (smart key ECU assembly) and ID code box/OK or NG OK: Verification result normal
NG: Verification result abnormal
When a malfunction is present:
·

The ID code for the certification ECU (smart key ECU assembly) or ID code box is not registered or the certification ECU (smart key ECU assembly) or ID code box is malfunctioning.

·

The gearshift control cannot be locked.

·

The gearshift control cannot be unlocked (the hybrid control system cannot be started).



OK:

OK appears on the screen.




OK

9.READ VALUE USING GTS (STARTER REQUEST SIGNAL)

NG

10.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
9.READ VALUE USING GTS (STARTER REQUEST SIGNAL)
a.

Connect the Techstream to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

Read the Data List according to the display on the GTS.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Starter Request Signal Condition of hybrid control system start command signal/OFF or ON OFF: Power switch released after approximately 1 second elapses
ON: Power switch pressed and held while carrying key with park (P) selected and brake pedal depressed
·

This item displays "ON" when starting the hybrid control system.

·

The hybrid control system cannot be started when this item is "OFF".



OK:

Data List display changes when the power switch is operated.




OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

10.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly).

HINT:

Refer to the Service Bulletin.




NEXT

11.CHECK HYBRID SYSTEM READY ON
11.CHECK HYBRID SYSTEM READY ON
a.

Place the electrical key transmitter sub-assembly (key) on the driver seat.


b.

Push the P position switch (transmission shift main switch).


c.

Depress the brake pedal.


d.

Check that the power switch indicator light is green. Then press the power switch to check if the hybrid system turns on (READY).

OK:

Power source mode becomes on (READY).




OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

12.REPLACE TRANSMISSION CONTROL ECU ASSEMBLY
a.

Replace transmission control ECU assembly (See page Drivetrain>P410 (HYBRID TRANSMISSION / TRANSAXLE)>SHIFT LEVER>REMOVAL).



NEXT

13.CHECK HYBRID SYSTEM READY ON
13.CHECK HYBRID SYSTEM READY ON
a.

Place the electrical key transmitter sub-assembly (key) on the driver seat.


b.

Depress the brake pedal.


c.

Check that the power switch indicator light is green. Then press the power switch to check if the hybrid system turns on (READY).

OK:

Power source mode becomes on (READY).




OK

END (TRANSMISSION CONTROL ECU ASSEMBLY WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

14.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SOURCE AND BODY GROUND)

OK

15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - STOP LIGHT SWITCH ASSEMBLY)

OK

16.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.INSPECT STOP LIGHT SWITCH ASSEMBLY

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY