Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2012.03–2014.11
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301770 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Glass Breakage Sensor Circuit  


DESCRIPTION

When the main body ECU (multiplex network body ECU) detects that the glass breakage sensor (quarter window assembly RH, quarter window assembly LH or back door glass is broken, the theft deterrent system switches from the armed state to the alarm sounding state.

WIRING DIAGRAM

B313242E02
1.063,0.833 1.521,1.031 0.458,0.198 10 false S32 2.563,0.844 3.021,1.042 0.458,0.198 10 false S31 1.427,0.75 1.823,0.979 0.396,0.229 10 false SSR- 1.156,0.625 1.313,0.823 0.156,0.198 10 false 1 2.646,0.625 2.802,0.823 0.156,0.198 10 false 1 2.646,3.208 2.802,3.406 0.156,0.198 10 false 1 1.146,3.208 1.302,3.406 0.156,0.198 10 false 1 3.49,3.302 3.646,3.5 0.156,0.198 10 false 1 2.115,0.75 2.51,0.979 0.396,0.229 10 false SSR+ 1.073,1.344 3.063,1.708 1.99,0.365 10 false Glass Breakage Sensor (Quarter Window Assembly RH) 3.969,0.833 4.427,1.031 0.458,0.198 10 false 2B 3.979,0.635 4.292,0.833 0.313,0.198 10 false 15 4.979,0.729 5.438,0.927 0.458,0.198 10 false 19 5.208,0.854 5.667,1.052 0.458,0.198 10 false GPBS 1.083,3.406 1.542,3.604 0.458,0.198 10 false R37 2.573,3.406 3.031,3.604 0.458,0.198 10 false R38 2.135,3.323 2.531,3.552 0.396,0.229 10 false SSR- 1.427,3.313 1.823,3.542 0.396,0.229 10 false SSR+ 3.656,3.323 4.052,3.552 0.396,0.229 10 false SSR+ 1,3.958 3.01,4.354 2.01,0.396 10 false Glass Breakage Sensor (Quarter Window Assembly LH) 3.448,4.135 4.938,4.5 1.49,0.365 10 false Glass Breakage Sensor (Back Door Glass) 3.458,3.958 3.854,4.188 0.396,0.229 10 false V12 3.885,1.344 4.948,1.865 1.063,0.521 10 false Instrument Panel Junction Block Assembly 5.167,2.438 6.781,2.802 1.615,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 5.167,2.281 5.625,2.479 0.458,0.198 10 false MB

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

According to the display on the GTS, read the Data List.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Sealed Glas Brak Sen Glass breakage sensor connecting/With or Without With: Glass breakage sensor connected
Without: Glass breakage sensor not connected
-

OK:

With appear on the tester screen.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).

U125019E01
0.178,0.125 0.349,0.269 0.172,0.144 10 *a 1.313,0.536 1.500,0.673 0.187,0.137 10 2B 4.816,0.529 5.041,0.666 0.225,0.137 10 MB 4.716,1.53 5.122,1.669 0.406,0.140 10 GPBS 5.246,1.261 5.246,1.597 5.246,1.597 5.124,1.597 false


b.

Disconnect the 2B instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2B-15 - MB-19 (GPBS) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



OK

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - QUARTER WINDOW ASSEMBLY RH)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - QUARTER WINDOW ASSEMBLY RH)
a.

Disconnect the S31 glass breakage sensor (quarter window assembly RH) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2B-15 - S31-1 (SSR+) Always Below 1 Ω
S31-1 (SSR+) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (QUARTER WINDOW ASSEMBLY RH - QUARTER WINDOW ASSEMBLY LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (QUARTER WINDOW ASSEMBLY RH - QUARTER WINDOW ASSEMBLY LH)
a.

Disconnect the S32 glass breakage sensor (quarter window assembly RH) connector.


b.

Disconnect the R37 glass breakage sensor (quarter window assembly LH) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S32-1 (SSR-) - R37-1 (SSR+) Always Below 1 Ω
R37-1 (SSR+) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (QUARTER WINDOW ASSEMBLY LH - BACK DOOR GLASS)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (QUARTER WINDOW ASSEMBLY LH - BACK DOOR GLASS)
a.

Disconnect the R38 glass breakage sensor (quarter window assembly LH) connector.


b.

Disconnect the V12 glass breakage sensor (back door glass) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R38-1 (SSR-) - V12-1 (SSR+) Always Below 1 Ω
V12-1 (SSR+) - Body ground Always 10 kΩ or higher




OK

6.INSPECT GLASS BREAKAGE SENSOR (QUARTER WINDOW ASSEMBLY RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT GLASS BREAKAGE SENSOR (QUARTER WINDOW ASSEMBLY RH)
a.
B313244

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SSR+) - 1 (SSR-) Always Below 1 Ω
1 (SSR+) - Body ground Always 10 kΩ or higher




OK

7.INSPECT GLASS BREAKAGE SENSOR (QUARTER WINDOW ASSEMBLY LH)

NG

REPLACE GLASS BREAKAGE SENSOR (QUARTER WINDOW ASSEMBLY RH)

7.INSPECT GLASS BREAKAGE SENSOR (QUARTER WINDOW ASSEMBLY LH)
a.
B313243

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SSR+) - 1 (SSR-) Always Below 1 Ω
1 (SSR+) - Body ground Always 10 kΩ or higher




OK

REPLACE GLASS BREAKAGE SENSOR (BACK DOOR GLASS)

NG

REPLACE GLASS BREAKAGE SENSOR (QUARTER WINDOW ASSEMBLY LH)