In this circuit, the combination meter sub-assembly receives engine coolant temperature signals from the ECM using the CAN communication system. The combination meter sub-assembly displays engine coolant temperature warnings based on the data received from the ECM.
If there is an open or short in the engine coolant temperature sensor circuit, the ECM stores the DTCs. Troubleshoot the SFI system (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
If the exhaust heat recirculation system has a malfunction, the water temperature warning light comes on to inform the driver of the malfunction.
Check if CAN communication DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).
| Result | Proceed to |
|---|---|
| CAN communication DTCs are not output. | A |
| CAN communication DTCs are output. | B |
A
B
Check the Water temperature warning light.
| Result | Proceed to |
|---|---|
| Water temperature warning light does not come on. | A |
| Water temperature warning light remains on. | B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Active Test.
Check the operation by referring to the table below.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Indicat. Lamp Coolant Hot | Water temperature warning light | OFF or ON | - |
Water temperature warning light operation is normal.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/o Multi-information display) | B |
| NG (w/ Multi-information display) | C |
A
B
C
Check for DTCs (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR for SFI System, Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR for Meter/Gauge System).
| Result | Proceed to |
|---|---|
| DTC is not output. | A |
| DTC of SFI system is output. | B |
| DTC B1503 is output. | C |
A
B
(See pageEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
C
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus:
for Combination Meter: Body Electrical / Combination Meter / Data List.
for Engine: Powertrain / Engine and ECT / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Coolant Temperature | Engine coolant temperature / 0 to 127.5°C (0 to 261.5°F) | After warming up: 75 to 100°C (167 to 212°F) | - |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Coolant Temp | Engine coolant temperature/
Min.: -40°C (-40°F), Max.: 140°C (284°F) |
75 to 100°C (167 to 212°F): After warming up | Yes |
| Diagnostic Note:
This is the engine coolant temperature.
|
|||
Enter inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
| Result | Proceed to |
|---|---|
| The data list values of the ECUs do not match (w/o Multi-information display). | A |
| The data list values of the ECUs do not match (w/ Multi-information display). | B |
| The data list values of the ECUs match. | C |
When the Data List values of the ECUs do not match, a signal output error of the ECM is suspected.
A
B
C
(See pageEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
Replace the meter circuit plate with a new or a known good one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>DISASSEMBLY).
The operation of the water temperature warning light returns to normal.
OK
NG
Replace the combination meter sub-assembly with a new or a known good one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).
The operation of the water temperature warning light returns to normal.
OK
NG