Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2014.11–2020.08
RM2070E _58 Vehicle Interior _061940 METER / GAUGE / DISPLAY _0301792 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1503  Exhaust Heat Management Warning Detected  


DESCRIPTION

This DTC is stored when the combination meter sub-assembly detects a malfunction in the engine coolant temperature sensor that is connected to the combination meter sub-assembly via a direct line.

DTC No. DTC Detection Condition Trouble Area
B1503 When IG voltage is 9.5 V or more and the following condition is detected:
1.

Engine coolant temperature sensor operation malfunction

2.

Engine coolant temperature sensor circuit open or shorted

3.

Engine coolant temperature is 120°C (248°F) or more


·

Harness or connector

·

Engine coolant temperature sensor

·

Combination meter sub-assembly



HINT:

This DTC is for the engine coolant temperature sensor which is used to detect the engine coolant temperature for the exhaust heat recirculation system, not for the engine coolant temperature sensor which is used for the SFI system.


WIRING DIAGRAM

E230581E13
2.221,0.902 2.331,1.051 0.111,0.149 10 1 2.239,2.247 2.350,2.396 0.111,0.149 10 2 1.973,0.914 2.178,1.063 0.205,0.149 10 E2 1.756,2.247 2.176,2.396 0.420,0.149 10 TWS3 0.748,3.026 0.987,3.203 0.239,0.177 10 G1 0.748,3.19 2.147,3.501 1.399,0.311 10 Engine Coolant Temperature Sensor 4.8,2.967 5.081,3.143 0.281,0.177 10 L27 4.8,3.13 6.968,3.469 2.169,0.339 10 Combination Meter Sub-assembly 5.406,0.902 5.607,1.065 0.201,0.163 10 9 5.606,1.001 5.831,1.156 0.225,0.155 10 E2 5.406,2.247 5.583,2.389 0.177,0.142 10 8 5.606,2.356 6.019,2.528 0.413,0.172 10 TWS3

PROCEDURE

1.READ VALUE USING GTS (COOLANT TEMPERATURE)
a.

Set the vehicle in maintenance mode using the GTS (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Combination Meter / Data List.


f.

Check the values by referring to the table below.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Coolant Temperature Engine coolant temperature/0 to 127.5°C (0 to 261.5°F) After warming up: 75 to 100°C (167 to 212°F) -

HINT:
·

The coolant temperature value in this inspection is the data sent from the engine coolant temperature sensor for the SFI system.

·

When the Data List values do not match, a signal output error of the ECM is suspected.



OK:

Engine coolant temperature displayed on the GTS is 75 to 100°C (167 to 212°F) after warming up.




OK

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - ENGINE COOLANT TEMPERATURE SENSOR)

NG

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - ENGINE COOLANT TEMPERATURE SENSOR)
a.

Disconnect the L27 combination meter sub-assembly connector.


b.

Disconnect the G1 engine coolant temperature sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L27-8 (TWS3) - G1-2 Always Below 1 Ω
L27-9 (E2) - G1-1 Always Below 1 Ω
L27-8 (TWS3) - Body ground Always 10 kΩ or higher
L27-9 (E2) - Body ground Always 10 kΩ or higher




OK

3.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Remove the G1 engine coolant temperature sensor (See page Engine / Hybrid System>2ZR-FXE (COOLING)>TEMPERATURE SWITCH>REMOVAL).

E319158E01
0.375,0.365 0.688,0.563 0.313,0.198 10 false *a 4.385,0.156 4.698,0.354 0.313,0.198 10 false *b 4.792,2.323 5.177,2.792 0.385,0.469 10 false -20 5.063,2.323 5.417,2.792 0.354,0.469 10 false 0 5.24,2.323 5.594,2.792 0.354,0.469 10 false 20 5.469,2.323 5.823,2.792 0.354,0.469 10 false 40 5.698,2.323 6.052,2.792 0.354,0.469 10 false 60 5.917,2.323 6.271,2.792 0.354,0.469 10 false 80 6.104,2.323 6.458,2.792 0.354,0.469 10 false 100 6.5,2.323 6.854,2.792 0.354,0.469 10 false *c 4.802,2.5 5.135,2.792 0.333,0.292 8 false (-4) 6.146,2.5 6.479,2.792 0.333,0.292 8 false (212) 5.875,2.5 6.208,2.792 0.333,0.292 8 false (176) 5.625,2.5 5.958,2.792 0.333,0.292 8 false (140) 5.385,2.5 5.719,2.792 0.333,0.292 8 false (104) 5.198,2.5 5.531,2.792 0.333,0.292 8 false (68) 5,2.5 5.333,2.792 0.333,0.292 8 false (32) 4.521,0.552 7.156,0.875 2.635,0.323 10 false 20 4.521,0.75 7.156,1.073 2.635,0.323 10 false 10 4.604,0.927 7.156,1.25 2.552,0.323 10 false 5 4.604,1.417 7.156,1.74 2.552,0.323 10 false 1 4.604,1.198 7.156,1.521 2.552,0.323 10 false 2 4.49,1.667 7.125,1.99 2.635,0.323 10 false 0.3 4.49,1.885 7.125,2.208 2.635,0.323 10 false 0.1


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-1 - G1-2 Temperature is 20°C (68°F) 2.32 to 2.59 kΩ
G1-1 - G1-2 Temperature is 80°C (176°F) 0.310 to 0.326 kΩ


Text in Illustration
*a Component without harness connected
(Engine Coolant Temperature Sensor)
*b Resistance kΩ
*c Temperature °C (°F)

Result
Result Proceed to
OK (w/o Multi-information display) A
OK (w/ Multi-information display) B
NG C



A

B

REPLACE COMBINATION METER SUB-ASSEMBLY

C

REPLACE ENGINE COOLANT TEMPERATURE SENSOR