Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2014.11–2020.08
RM2070E _58 Vehicle Interior _061940 METER / GAUGE / DISPLAY _0301792 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1500  Fuel Sender Open Detected  


DESCRIPTION

This DTC is stored when the combination meter sub-assembly detects a fuel sender gauge malfunction via a direct line.

DTC No. DTC Detection Condition Trouble Area
B1500 When IG voltage is 9.5 V or more and the following condition is detected:
1.

Fuel sender gauge operation malfunction


·

Harness or connector

·

Fuel sender gauge assembly

·

Combination meter sub-assembly



WIRING DIAGRAM

E230580E55
4.958,3.104 7.146,3.458 2.188,0.354 10 false Combination Meter Sub-assembly 5.719,0.979 5.99,1.135 0.271,0.156 10 false L 5.719,2.344 6.125,2.5 0.406,0.156 10 false ES 2 5.479,0.885 5.938,1.271 0.458,0.385 10 false 12 5.469,2.24 5.823,2.583 0.354,0.344 10 false 13 2.323,2.229 2.438,2.375 0.115,0.146 10 false 3 2.323,0.885 2.438,1.031 0.115,0.146 10 false 2 0.656,3.135 4.771,3.313 4.115,0.177 10 false Fuel Sender Gauge Assembly 0.781,1.448 1.219,1.615 0.438,0.167 10 false Fuel 2.031,2.229 2.281,2.406 0.25,0.177 10 false FE 2.042,0.885 2.344,1.177 0.302,0.292 10 false FS 4.969,2.938 5.479,3.271 0.51,0.333 10 false L27 0.656,2.979 1.333,3.333 0.677,0.354 10 false R11 1.698,2.01 1.813,2.156 0.115,0.146 10 false 1 1.688,1.354 1.802,1.5 0.115,0.146 10 false 2 0.771,1.625 1.313,1.802 0.542,0.177 10 false Sender 0.771,1.792 1.271,2 0.5,0.208 10 false Gauge 0.771,1.948 1.49,2.146 0.719,0.198 10 false Assembly

PROCEDURE

1.READ VALUE USING GTS (FUEL INPUT)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Fuel Input Fuel input/Min.: 0, Max.: 127.5 10th segment comes on:
39.8 to 45.0
Unit: Liter
9th segment comes on:
36.2 to 39.8
8th segment comes on:
32.6 to 36.2
7th segment comes on:
28.6 to 32.6
6th segment comes on:
24.4 to 28.6
5th segment comes on:
20.1 to 24.4
4th segment comes on:
16.0 to 20.1
3rd segment comes on:
12.5 to 16.0
2nd segment comes on:
8.6 to 12.5
1st segment comes on:
4.8 to 8.6

Result:
Result Proceed to
Fuel level data can be displayed on the GTS (w/o Multi-information display). A
Fuel level data can be displayed on the GTS (w/ Multi-information display). B
Fuel level data cannot be displayed on the GTS. C




A

B

REPLACE COMBINATION METER SUB-ASSEMBLY

C

2.INSPECT FUEL SENDER GAUGE ASSEMBLY
2.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.
U155024E01
0.242,0.223 0.422,0.407 0.179,0.184 10 *a 0.859,1.315 1.157,1.496 0.298,0.181 10 L27 2.678,1.531 2.826,1.678 0.148,0.146 10 L 2.932,1.845 3.313,2.023 0.381,0.178 10 ES 2 2.614,1.64 1.92,2.35 false 2.034,2.351 2.896,1.952 false

Disconnect the L27 combination meter sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L27-12 (L) - L27-13 (ES 2) Always 12 to 415 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Sub-assembly)


Result
Result Proceed to
OK (w/o Multi-information display) A
OK (w/ Multi-information display) B
NG C


A

B

REPLACE COMBINATION METER SUB-ASSEMBLY

C

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY)
a.

Disconnect the R11 fuel suction with pump and gauge tube assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L27-12 (L) - R11-2 (FS) Always Below 1 Ω
L27-12 (L) - Body ground Always 10 kΩ or higher
L27-13 (ES 2) - R11-3 (FE) Always Below 1 Ω
L27-13 (ES 2) - Body ground Always 10 kΩ or higher




OK

4.FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.FUEL SENDER GAUGE ASSEMBLY
a.

Remove the fuel sender gauge assembly (See page Engine / Hybrid System>2ZR-FXE (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL).


b.

Inspect the fuel sender gauge assembly (See page Engine / Hybrid System>2ZR-FXE (FUEL)>FUEL SENDER GAUGE ASSEMBLY>INSPECTION).

Result
Result Proceed to
OK (w/o Multi-information display) A
OK (w/ Multi-information display) B
NG C



A

B

REPLACE COMBINATION METER SUB-ASSEMBLY

C