Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2016.05–2020.08
RM2070E _58 Vehicle Interior _061940 METER / GAUGE / DISPLAY _0301792 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Hybrid System Indicator Malfunction  


DESCRIPTION

A hybrid system indicator is adopted for this vehicle. In this circuit, the combination meter sub-assembly receives the hybrid system indicator level signal from the hybrid vehicle control ECU assembly via the CAN communication line. The combination meter sub-assembly controls the operation of the hybrid system indicator according to the hybrid system indicator level signal received from the hybrid vehicle control ECU assembly via the CAN communication line.

WIRING DIAGRAM

E225566E35
4.406,1.677 6.406,1.875 2,0.198 10 false Combination Meter Assembly 0.833,2.458 2.729,2.667 1.896,0.208 10 false : CAN Communication Line 1,1.677 3.094,1.854 2.094,0.177 10 false Hybrid Vehicle Control ECU

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM). (w/ Central Gateway ECU)


b.

Check if CAN communication DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM). (w/o Central Gateway ECU)

Result:
Result Proceed to
CAN communication DTCs are not output. A
CAN communication DTCs are output. (w/ Central Gateway ECU) B
CAN communication DTCs are output. (w/o Central Gateway ECU) C




A

2.PERFORM ACTIVE TEST USING GTS (HV SYSTEM INDICATOR)

B

C

2.PERFORM ACTIVE TEST USING GTS (HV SYSTEM INDICATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Check the indicator light operation according to the values in the table below.

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
HV System Indicator Hybrid System Indicator MIN, -50, 0, 100, MAX -

OK:

Hybrid system indicator indication is normal.

Result
Result Proceed to
OK A
NG (w/o Multi-information display) B
NG (w/ Multi-information display) C




A

3.READ VALUE USING GTS (HYBRID SYSTEM INDICATOR)

B

C

REPLACE COMBINATION METER SUB-ASSEMBLY

3.READ VALUE USING GTS (HYBRID SYSTEM INDICATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data Test.


e.

Check the values by referring to the table below.

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Hybrid System Indicator Hybrid system indicator value/ Min.: -512, Max.: 511 (%) -512 to 511 (%) -

OK:

Hybrid system indicator value displayed on the GTS is almost the same as hybrid system indicator indication.

Result
Result Proceed to
OK (w/o Multi-information display) A
OK (w/ Multi-information display) B
NG C




A

4.REPLACE METER CIRCUIT PLATE

B

5.REPLACE COMBINATION METER SUB-ASSEMBLY

C

4.REPLACE METER CIRCUIT PLATE
a.

Replace the meter circuit plate with a new or a known good one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>DISASSEMBLY).

OK:

The operation of the hybrid system indicator returns to normal.




OK

END

NG

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

5.REPLACE COMBINATION METER SUB-ASSEMBLY
a.

Replace the combination meter sub-assembly with a new or a known good one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).

OK:

The operation of the hybrid system indicator returns to normal.




OK

END

NG

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY