The headup display system displays some vehicle information on the windshield glass.
The headup display system consists of the combination mirror meter ECU and combination meter sub-assembly.
The combination mirror meter ECU receives information from the combination meter sub-assembly via communication and projects it on the windshield.
Before starting the following inspection, confirm the headup display position and illuminance, then perform the on-vehicle inspection (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).
Check the symptom of the headup display.
| Result | Proceed to |
|---|---|
| Headup display does not display at all. | A |
| Display of the headup display is abnormal. | B |
A
B
Disconnect the L160 combination meter mirror ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L160-1 (12V) - Body ground | Power switch on (IG) | 11 to 14 V |
Measure the resistance according to the value(s) in the table below
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L160-8 (GND) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector
(to Combination Meter Mirror ECU) |
OK
NG
Disconnect the L147 headup display switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L160-14 (HUDU) - L147-3 (NVM) | Always | Below 1 Ω |
| L160-14 (HUDU) - Body ground | Always | 10 kΩ or higher |
| L160-15 (HUDO) - L147-4 (CH) | Always | Below 1 Ω |
| L160-15 (HUDO) - Body ground | Always | 10 kΩ or higher |
| L160-16 (E) - L147-1 (E) | Always | Below 1 Ω |
| L160-16 (E) - Body ground | Always | Below 1 Ω |
OK
NG
Disconnect the L147 headup display switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3 (NVM) - 1 (E) | SET switch is pressed | 1782 to 1818 Ω |
| SET switch is not pressed | 10 kΩ or higher | |
| HUD tilt up switch is pressed | 811.8 to 828.2 Ω | |
| HUD tilt up switch is not pressed | 10 kΩ or higher | |
| HUD tilt down switch is pressed | 326.7 to 333.3 Ω | |
| HUD tilt down switch is not pressed | 10 kΩ or higher | |
| 4 (CH) - 1 (E) | HUD main switch is pressed | 1782 to 1818 Ω |
| HUD main switch is not pressed | 10 kΩ or higher | |
| HUD rheostat up switch is pressed | 811.8 to 828.2 Ω | |
| HUD rheostat up switch is not pressed | 10 kΩ or higher | |
| HUD rheostat down switch is pressed | 326.7 to 333.3 Ω | |
| HUD rheostat down switch is not pressed | 10 kΩ or higher |
| *a | Component without harness connected
(Headup Display Switch Assembly) |
OK
NG
Check the symptom of the headup display.
| Result | Proceed to |
|---|---|
| All display items are abnormal. | A |
| Vehicle speed display is abnormal. | |
| Dynamic radar cruise control display is abnormal. | |
| Pre-crash safety system display is abnormal. | |
| Touch tracer display is abnormal. | |
| Turn-by-turn navigation display is abnormal. | B |
A
B
Disconnect the L141 combination meter sub-assembly connector.
Disconnect the L160 combination meter mirror ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L141-7 (TX+) - L160-3 (SIH) | Always | Below 1 Ω |
| L141-7 (TX+) - Body ground | Always | 10 kΩ or higher |
| L141-8 (TX-) - L160-4 (SIL) | Always | Below 1 Ω |
| L141-8 (TX-) - Body ground | Always | 10 kΩ or higher |
| L141-9 (SIH) - L160-5 (TX+) | Always | Below 1 Ω |
| L141-9 (SIH) - Body ground | Always | 10 kΩ or higher |
| L141-10 (SIL) - L160-6 (TX-) | Always | Below 1 Ω |
| L141-10 (SIL) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the combination meter mirror ECU with a new or a known good one (See page Vehicle Interior>METER / GAUGE / DISPLAY>HEADUP DISPLAY>DISASSEMBLY).
The operation of the headup display returns to normal.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/o Multi-information display) | B |
| NG (w/ Multi-information display) | C |
OK
B
C
Disconnect the L141 combination meter sub-assembly connector.
Disconnect the L160 combination meter mirror ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L141-7 (TX+) - L160-3 (SIH) | Always | Below 1 Ω |
| L141-7 (TX+) - Body ground | Always | 10 kΩ or higher |
| L141-8 (TX-) - L160-4 (SIL) | Always | Below 1 Ω |
| L141-8 (TX-) - Body ground | Always | 10 kΩ or higher |
| L141-9 (SIH) - L160-5 (TX+) | Always | Below 1 Ω |
| L141-9 (SIH) - Body ground | Always | 10 kΩ or higher |
| L141-10 (SIL) - L160-6 (TX-) | Always | Below 1 Ω |
| L141-10 (SIL) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the combination meter mirror ECU with a new or a known good one (See page Vehicle Interior>METER / GAUGE / DISPLAY>HEADUP DISPLAY>DISASSEMBLY).
The operation of the headup display returns to normal.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/o Multi-information display) | B |
| NG (w/ Multi-information display) | C |
A
B
C
Replace the meter circuit plate with a new or a known good one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>DISASSEMBLY).
The operation of the headup display returns to normal.
OK
NG
Replace the combination meter sub-assembly with a new or a known good one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).
The operation of the headup display returns to normal.
OK
NG