57014A
1.INSTALL FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY LH
Engage the guide.
Install the front side member bracket sub-assembly LH with the 4 bolts.
57013C
2.INSTALL FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY RH
Use the same procedure as for the LH side.
52116A
3.INSTALL FRONT BUMPER SIDE SUPPORT LH
Engage the 2 claws.
| *1 | Bolt |
| *2 | Screw |
Install the front bumper side support LH with the bolt and screw.
52115A
4.INSTALL FRONT BUMPER SIDE SUPPORT RH
Use the same procedure as for the LH side.
52021
5.INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY
Engage the claw.
Install the front bumper reinforcement sub-assembly with the 6 bolts.
Engage the 3 clamps.
52611
6.INSTALL FRONT BUMPER ENERGY ABSORBER
Engage the 4 guides to install the front bumper energy absorber.
52543B
7.INSTALL FRONT BUMPER SEAL
Clean the front bumper reinforcement sub-assembly surface.
Remove the double-sided tape from the front bumper reinforcement sub-assembly.
Wipe off any tape adhesive residue with cleaner.
Remove the release paper from the front bumper seal.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Install a new front bumper seal.
| *1 | Double-sided Tape |
Use the same procedure for the RH side and LH side.
53112E
8.INSTALL NO. 1 LOWER RADIATOR GRILLE
Engage the 16 claws to install the No. 1 lower radiator grille.
81482C
9.INSTALL FOG LIGHT COVER LH
Engage the 7 claws to install the fog light cover LH.
81481E
10.INSTALL FOG LIGHT COVER RH
Use the same procedure as for the LH side.
52128B
11.INSTALL FRONT BUMPER HOLE COVER LH
Engage the hook.
| *1 | Hook |
Engage the 2 claws and install the front bumper hole cover LH.
52127C
12.INSTALL FRONT BUMPER HOLE COVER RH
Use the same procedure as for the LH side.
53879A
13.INSTALL FRONT FENDER LINER RETAINER
Engage the claw and install the front fender liner retainer.
Use the same procedure for the RH side and LH side.
53101
14.INSTALL RADIATOR GRILLE SUB-ASSEMBLY
Engage the 14 claws and guide to install the radiator grille.
Install the 4 clips.
Install the 2 screws.
75301A
15.INSTALL FRONT BUMPER EMBLEM SUB-ASSEMBLY
Engage the 2 pins and 4 claws.
Install the front bumper emblem sub-assembly with the 2 screws.
82113
16.INSTALL NO. 3 ENGINE ROOM WIRE
Engage the 8 clamps to install the No. 3 engine room wire.
17.INSTALL HEADLIGHT CLEANER HOSE (w/ Headlight Cleaner System)
Engage the 9 clamps to install the headlight cleaner hose.
53395E
18.INSTALL HOOD TO FRONT END PANEL SEAL
Wipe off any tape adhesive residue with cleaner.
Engage the 2 clips to install a new hood to front end panel seal.
| *1 | Double-sided Tape |
52114A
19.INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET
Engage the 2 claws.
Install the front bumper extension mounting bracket with the 2 screws.
81220
20.INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)
81210A
21.INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)
Use the same procedure as for the LH side.
81520
22.INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY LH
81510
23.INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY RH
Use the same procedure as for the LH side.
89348
24.INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (w/ Intelligent Parking Assist System)
89341A
25.INSTALL NO. 1 ULTRASONIC SENSOR (w/ Intelligent Parking Assist System)
89348D
26.INSTALL ULTRASONIC SENSOR CLIP (w/ Intelligent Parking Assist System)
85208A
27.INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)
85207A
28.INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)
Use the same procedure as for the LH side.
85045
29.INSTALL HEADLIGHT CLEANER WASHER NOZZLE LH (w/ Headlight Cleaner System)
85044
30.INSTALL HEADLIGHT CLEANER WASHER NOZZLE RH (w/ Headlight Cleaner System)
Use the same procedure as for the LH side.
76851E
31.INSTALL FRONT SPOILER