Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR DOOR WINDOW FRAME MOULDING › 2012.03–2013.08
RM2070E _59 Vehicle Exterior _061955 EXTERIOR PANELS / TRIM _0301938 REAR DOOR WINDOW FRAME MOULDING A

EXTERIOR PANELS / TRIM  REAR DOOR WINDOW FRAME MOULDING  INSTALLATION  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 75762A 2.INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING

HINT:

When installing the rear door front window frame moulding, heat the vehicle body and rear door front window frame moulding using a heat light.


Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Moulding 20 to 30°C (68 to 86°F)

NOTICE:

Do not heat the vehicle body or rear door front window frame moulding excessively.


a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove the double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Clean the rear door front window frame moulding (if reusing the rear door front window frame moulding).

i.

Using a heat light, heat the rear door front window frame moulding.


ii.

Remove the double-sided tape from the rear door front window frame moulding.


iii.

Wipe off any tape adhesive residue with cleaner.


iv.
B286824E02
0.563,0.625 0.344,0.938 true 0.25,3.281 0.542,2.802 true 1.063,1.927 0.604,1.667 true 0.531,0.458 0.708,0.646 0.177,0.188 10 false *1 1.083,1.917 1.281,2.083 0.198,0.167 10 false *2 0.125,3.292 0.323,3.458 0.198,0.167 10 false *3 2.031,0.25 2.208,0.438 0.177,0.188 10 false *1 2.042,1.771 2.24,1.938 0.198,0.167 10 false *2 2.042,2.99 2.24,3.156 0.198,0.167 10 false *3 1.729,1.052 1.875,1.219 0.146,0.167 10 false A 2.396,1.479 2.531,1.635 0.135,0.156 10 false C 2.375,4.031 2.51,4.188 0.135,0.156 10 false D 1.719,2.375 1.844,2.542 0.125,0.167 10 false B 2.396,2.792 2.531,2.958 0.135,0.167 10 false C 2.875,1.177 3.01,1.344 0.135,0.167 10 false E 1.719,3.604 1.854,3.771 0.135,0.167 10 false A 2.875,2.5 2.979,2.646 0.104,0.146 10 false F 2.896,3.729 3.031,3.875 0.135,0.146 10 false G

Apply new double-sided tape to the rear door front window frame moulding.

Text in Illustration
*1 Double-sided Tape (A)
*2 Double-sided Tape (B)
*3 Double-sided Tape (C)

Item Dimension
A 0.8 mm (0.0315 in.)
B 1.2 mm (0.0472 in.)
C 5.0 mm (0.197 in.)
D 15.0 mm (0.591 in.)
E 40.0 mm (1.57 in.)
F 410.0 mm (1.35 ft.)
G 450.0 mm (1.48 ft.)



c.
B275157E03
2.563,0.125 2.271,0.719 true 1.635,1.333 1.969,1.333 true 2.156,2.542 1.802,2.542 true 2.563,0.021 2.865,0.323 0.302,0.302 10 false *1 1.438,1.26 1.74,1.563 0.302,0.302 10 false *1 2.208,2.458 2.51,2.76 0.302,0.302 10 false *1

Install the rear door front window frame moulding.

Text in Illustration
*1 Double-sided Tape

i.

Using a heat light, heat the vehicle body and rear door front window frame moulding.


ii.

Remove the release paper from the face of the rear door front window frame moulding.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



iii.

Engage the clip and guide to install the rear door front window frame moulding.



Hide 75740 3.INSTALL REAR DOOR BELT MOULDING ASSEMBLY

Hide 68104 4.INSTALL REAR DOOR GLASS SUB-ASSEMBLY

Hide 67488C 5.INSTALL REAR DOOR REAR GUIDE SEAL

Hide 67408D 6.INSTALL REAR DOOR WINDOW GUIDE SUB-ASSEMBLY

Hide 68152C 7.INSTALL REAR DOOR GLASS RUN

Hide 67842E 8.INSTALL REAR DOOR SERVICE HOLE COVER

Hide 67628 9.INSTALL REAR DOOR TRIM BRACKET

Hide 67604 10.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

Hide 74262 11.INSTALL REAR DOOR ARMREST COVER

Hide 12.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

Hide 69284D 13.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG

Hide 14.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 20.INITIALIZE POWER WINDOW CONTROL SYSTEM