The skid control ECU receives signals from the yaw rate and acceleration sensor (airbag ECU assembly) via the CAN communication system.
The airbag ECU assembly has a built-in yaw rate and acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).
If there are any problems in the bus lines between the yaw rate and acceleration sensor (airbag ECU assembly) and the CAN communication system, DTCs U0123 (Lost Communication With Yaw Rate Sensor Module) and U0124 (Lost Communication With Lateral Acceleration Sensor Module) are output.
These DTCs are also output when calibration has not been completed.
DTC C1279 will be cleared when the yaw rate and acceleration sensor (airbag ECU assembly) sends a yaw rate and/or acceleration signal or when Test Mode ends. DTC C1279 is output only in Test Mode.
| DTC Code | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1234 | 711 | While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor self-check (Sensor 1 (GL1) malfunction). | Yaw rate sensor (Airbag ECU assembly) internal malfunction |
| ↑ | 712 | While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor self-check (Sensor 2 (GL2) malfunction). | ↑ |
| ↑ | 713 | While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor self-check (Zero point calibration malfunction). | ↑ |
| ↑ | 714 | While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor self-check (Two-value comparison malfunction). | ↑ |
| C1243 | 561 | An acceleration sensor malfunction occurs 16 times or more when the vehicle speed drops from above 30 km/h (19 mph) to 0 km/h (0 mph). | Acceleration sensor (Airbag ECU assembly) internal stuck malfunction |
| ↑ | 562
563 564 565 |
A stuck acceleration sensor value is determined. | ↑ |
| C1244 | 571 | Either of the following is detected:
1.
Difference between GL1 and GL2 does not become less than 0.4 G for 60 seconds or more after reaching 0.6 G when the vehicle is stopped. 2.
A malfunction signal from the acceleration sensor is received. |
·
Acceleration sensor (Airbag ECU assembly) installed improperly ·
Acceleration sensor (Airbag ECU assembly) |
| C1245 | 581 | Difference between longitudinal G calculated from the acceleration sensor value and that calculated from the vehicle speed exceeds 0.35 G for 60 seconds or more. | ·
Acceleration sensor (Airbag ECU assembly) installed improperly ·
Acceleration sensor (Airbag ECU assembly) |
| C1381 | 601 | While acceleration sensor communication is enabled, a supply voltage malfunction signal is received from the sensor for 10 seconds. | ·
Acceleration sensor (Airbag ECU assembly) supply voltage shut down ·
Acceleration sensor (Airbag ECU assembly) ·
Brake booster with master cylinder (Skid control ECU) |
| C1279 | - | Detected only during Test Mode. | ·
Sensor installation ·
Acceleration sensor (Airbag ECU assembly) |
When replacing the yaw rate and acceleration sensor (airbag ECU assembly), perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION).
When U0123 and/or U0124 is output together with C1234, C1243, C1244, C1245, and/or C1381, inspect and repair the trouble areas indicated by U0123 and/or U0124 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>U0073).
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the power switch off (lock).
Turn the power switch on (ready).
Drive the vehicle at a speed of 30 km/h (19 mph) or more, turn the steering wheel, and decelerate (depress the brake pedal) the vehicle.
Turn the power switch on (IG) again and check that no CAN communication system DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM for with Central Gateway ECU or Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM for without Central Gateway ECU).
Check if DTC C1210 (Zero Point Calibration of Yaw Rate Sensor undone) or C1336 (Zero Point Calibration of Deceleration Sensor undone) is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs (C1210, C1336 and CAN communication system DTC) are not output | A |
| CAN communication system DTC is output (w/ Central Gateway ECU) | B |
| CAN communication system DTC is output (w/o Central Gateway ECU) | C |
| DTCs (C1210 and/or C1336) are output | D |
A
B
C
D
Turn the power switch off (lock).
Check that the yaw rate and acceleration sensor (airbag ECU assembly) has been installed properly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION).
The airbag ECU assembly is tightened to the specified torque.
The airbag ECU assembly is not tilted.
OK
NG
(See pageVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION)
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the yaw rate and acceleration sensor (airbag ECU assembly) connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L16-21 (IG2) - Body ground | Power switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag ECU Assembly)) |
OK
NG
Turn the power switch off (lock).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L16-25 (E1) - Body ground | Always | Below 1 Ω |
| L16-26 (E2) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag ECU Assembly)) |
Check the yaw rate and acceleration sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).
OK
NG