Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2017.12
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301639 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  Cruise Control Switch Circuit  


DESCRIPTION

The cruise control switch is used to turn the cruise control system on and off, as well as operate 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP and CANCEL. The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + (ACCEL) functions are operated with the same switch. The cruise control switch is an automatic return type switch which turns on only while operating it in the direction of each arrow and turns off after releasing it. The internal contact points of the cruise control switch turn on with switch operation. Then the hybrid vehicle control ECU reads the voltage value that has been changed by the switch operation to control SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL.

WIRING DIAGRAM

E229591E47
6.333,0.833 6.677,0.99 0.344,0.156 10 false CCS 6.344,1.521 6.531,1.677 0.188,0.156 10 false E1 5.99,1.5 6.229,1.719 0.24,0.219 10 false L5 6.042,1.313 6.229,1.469 0.188,0.156 10 false 6 5.063,3.073 5.167,3.229 0.104,0.156 10 false 1 5.052,3.969 5.156,4.125 0.104,0.156 10 false 2 3.979,3.063 4.083,3.219 0.104,0.156 10 false 3 3.99,3.948 4.104,4.104 0.115,0.156 10 false 4 5.99,0.615 6.177,0.771 0.188,0.156 10 false 28 5.99,0.823 6.24,1.052 0.25,0.229 10 false L5 4.979,3.281 5.313,3.469 0.333,0.188 10 false L52 4.958,4.177 5.229,4.333 0.271,0.156 10 false L52 3.906,3.271 4.219,3.49 0.313,0.219 10 false z10 4.552,3.188 4.875,3.344 0.323,0.156 10 false CCS 6.125,5.188 7.031,5.625 0.906,0.438 10 false Hybrid Vehicle Control ECU 4.552,4.083 4.875,4.24 0.323,0.156 10 false ECC 3.906,4.167 4.188,4.354 0.281,0.188 10 false z10 1.156,4.708 2.625,4.865 1.469,0.156 10 false Cruise Control Switch 3.25,4.792 4.146,5.135 0.896,0.344 10 false Cruise Control Switch Wire 3.115,4.302 3.438,4.458 0.323,0.156 10 false ECC 3.115,3.188 3.438,3.344 0.323,0.156 10 false CCS 3.5,3.188 3.656,3.344 0.156,0.156 10 false 3 3.49,4.302 3.625,4.458 0.135,0.156 10 false 1 2.875,3.76 3.438,3.917 0.563,0.156 10 false ON-OFF 2.115,3.76 2.583,3.917 0.469,0.156 10 false +/RES 1.344,3.76 1.74,3.917 0.396,0.156 10 false -/SET 0.531,3.76 1.115,3.917 0.583,0.156 10 false CANCEL 4.271,4.677 5.552,5.094 1.281,0.417 10 false Spiral with Sensor Cable Sub-assembly

PROCEDURE

1.READ VALUE ON GTS
E107091E35
2.146,0.156 2.417,0.344 0.271,0.188 10 false *c 2.781,1.26 3.021,1.458 0.24,0.198 10 false *a 1.958,1.688 2.344,1.885 0.385,0.198 10 false *b 1.031,1.313 1.271,1.51 0.24,0.198 10 false *d

a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Select the following menu items: Powertrain / Cruise Control / Data List.


e.

Check the Data List to confirm proper functioning of the cruise control switch.

Text in Illustration
*a ON-OFF
*b -/SET
*c +/RES
*d CANCEL

Cruise Control
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Cancel Switch CANCEL switch status ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
-SET Switch -SET switch status ON or OFF ON: -SET switch on
OFF: -SET switch off
-
+RES Switch +RES switch status ON or OFF ON: +RES switch on
OFF: +RES switch off
-
Cruise Main Switch Operation Condition Cruise control main switch (ON-OFF button) status ON or OFF ON: Cruise control main switch pushed
OFF: Cruise control main switch not pushed
-

OK:

When the cruise control switch is operated, the display changes as shown above.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT CRUISE CONTROL SWITCH
2.INSPECT CRUISE CONTROL SWITCH
a.

b.

Measure the resistance according to the value(s) in the table below.

E319149E01
5.344,1.125 5.969,0.323 5.969,0.323 6.135,0.323 false 0.281,0.125 0.594,0.323 0.313,0.198 10 false *a 4.76,0.5 5.073,0.698 0.313,0.198 10 false *c 6.198,0.24 6.51,0.438 0.313,0.198 10 false *1 6.208,1.208 6.521,1.406 0.313,0.198 10 false *b 5.146,2.417 5.458,2.615 0.313,0.198 10 false *d 3.979,2.052 4.292,2.25 0.313,0.198 10 false *e


Text in Illustration
*1 Cruise Control Switch (ON-OFF button) - -
*a Component without harness connected
(Cruise Control Switch)
*b ON-OFF
*c +/RES *d -/SET
*e CANCEL - -

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 3 Cruise control switch (ON-OFF button) released 1 MΩ or higher
Cruise control switch (ON-OFF button) pushed Below 2.5 Ω
+/RES 235 to 245 Ω
-/SET 617 to 643 Ω
CANCEL 1509 to 1571 Ω



OK

3.CHECK CRUISE CONTROL SWITCH WIRE (SPIRAL CABLE SUB-ASSEMBLY - CRUISE CONTROL SWITCH)

NG

3.CHECK CRUISE CONTROL SWITCH WIRE (SPIRAL CABLE SUB-ASSEMBLY - CRUISE CONTROL SWITCH)
a.

Disconnect the spiral with sensor cable sub-assembly connector.


U155127E02
0.229,1.427 0.531,1.583 0.302,0.156 9 false z10 0.083,0.042 0.438,0.292 0.354,0.25 10 false *a 0.094,2.26 0.531,2.479 0.438,0.219 10 false *b

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Specified Condition
z10-3 - 3 Below 2.5 Ω
z10-4 - 1 Below 2.5 Ω


Text in Illustration
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly)
*b Front view of wire harness connector
(to Cruise Control Switch)



OK

4.CHECK SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE CRUISE CONTROL SWITCH WIRE (SPIRAL CABLE SUB-ASSEMBLY - CRUISE CONTROL SWITCH)

4.CHECK SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY
NOTICE:

The spiral with sensor cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral with sensor cable sub-assembly may prevent the airbag from deploying. Be sure to read the pages shown in the brackets.


HINT:


a.

Remove the spiral with sensor cable sub-assembly.


E343931E01
3.083,3.448 3.5,3.698 0.417,0.25 3.667,1.083 4.083,1.333 0.417,0.25 3.01,4.396 3.208,4.094 false 3.542,4.458 3.281,4.094 false 1.896,0.115 2.208,0.313 0.313,0.198 10 false *a 3.76,1.125 4.073,1.323 0.313,0.198 10 false z10 3.167,3.5 3.479,3.698 0.313,0.198 10 false L52 2.833,4.469 3.24,4.667 0.406,0.198 10 false CCS 3.438,4.49 3.844,4.688 0.406,0.198 10 false ECC

b.

Measure the resistance according to the value(s) in the table below.


c.

After setting the spiral with sensor cable sub-assembly to the center position, rotate the spiral with sensor cable sub-assembly 2.5 times clockwise. Then while rotating the spiral with sensor cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
z10-3 - L52-1 (CCS) Always Below 1 Ω
z10-4 - L52-2 (ECC) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Spiral with Sensor Cable Sub-assembly)

HINT:

The spiral with sensor cable sub-assembly makes a maximum of approximately 5 rotations.




OK

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SPIRAL CABLE SUB-ASSEMBLY)

NG

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SPIRAL CABLE SUB-ASSEMBLY)
a.

Disconnect the hybrid vehicle control ECU connector.


b.

Disconnect the spiral with sensor cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
L52-1 (CCS) - L5-28 (CCS) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
L52-1 (CCS) or L5-28 (CCS) - Body ground Always 10 kΩ or higher



d.

Reconnect the spiral with sensor cable sub-assembly connector.


e.

Reconnect the hybrid vehicle control ECU connector.



OK

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - HYBRID VEHICLE CONTROL ECU)

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)
a.
U155030E02
1.438,1.615 1.083,2.25 true 0.156,0.104 0.406,0.313 0.25,0.208 10 false *a 0.563,1.531 0.917,1.698 0.354,0.167 10 false L52 0.938,2.281 1.271,2.448 0.333,0.167 10 false ECC

Disconnect the spiral with sensor cable sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
L52-2 (ECC) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly)


c.

Reconnect the spiral with sensor cable sub-assembly connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)