Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2020.08
RM2070E _58 Vehicle Interior _061940 METER / GAUGE / DISPLAY _0301792 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Odo/Trip Switch Malfunction  


DESCRIPTION

The combination meter sub-assembly and steering pad switch RH are connected via direct line. When the TRIP switch is operated, the display of the multi-information display changes or the displayed value is reset.

WIRING DIAGRAM

E449756E02
6.188,0.906 6.802,1.104 0.615,0.198 10 false 12 V 5.49,1.24 6.104,1.438 0.615,0.198 10 false ODO 4.969,2.104 7.042,2.521 2.073,0.417 10 false Combination Meter Sub-assembly 1.344,3.198 1.802,3.396 0.458,0.198 10 false TRIP 1.354,3.802 1.813,4 0.458,0.198 10 false EAU 1.281,4.885 2.802,5.5 1.521,0.615 10 false Spiral Cable with Sensor Sub-assembly 3.958,4.719 5.99,5.198 2.031,0.479 10 false Steering Pad Switch RH 5.198,1.24 5.813,1.438 0.615,0.198 10 false 24 4.979,1.927 5.594,2.125 0.615,0.198 10 false L27 1.146,3.198 1.604,3.396 0.458,0.198 10 false 9 1.146,3.802 1.604,4 0.458,0.198 10 false 4 4.448,4.125 4.906,4.323 0.458,0.198 10 false TRIP 1.292,4.708 1.75,4.906 0.458,0.198 10 false L52

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Drive Monitor Reset SW TRIP switch / OFF or ON OFF: TRIP switch on steering pad switch not pushed -
ON: TRIP switch on steering pad switch pushed


Result:
Result Proceed to
The Data List item changes correctly A
The Data List item do not change correctly B



A

REPLACE COMBINATION METER SUB-ASSEMBLY

B

2.INSPECT STEERING PAD SWITCH RH
2.INSPECT STEERING PAD SWITCH RH
a.

Remove the steering pad switch RH.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch RH.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH RH

3.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
a.

Remove the spiral cable with sensor sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable with sensor sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION

Result:
Proceed to
OK
NG




OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - COMBINATION METER SUB-ASSEMBLY AND BODY GROUND)

NG

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - COMBINATION METER SUB-ASSEMBLY AND BODY GROUND)
a.

Disconnect the L27 combination meter sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L52-9 (TRIP) - L27-24 (ODO) Always Below 1 Ω
L52-9 (TRIP) or L27-24 (ODO) - Body ground Always 10 kΩ or higher
L52-4 (EAU) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR