Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › from 2020.08
RM2070E _54 Brake _061923 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0301683 ELECTRONICALLY CONTROLLED BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  Brake Warning Light Remains ON  


DESCRIPTION

The skid control ECU is connected to the combination meter sub-assembly via CAN communication.

If any of the following is detected, the brake warning light / red (malfunction) remains on:

·

The skid control ECU connector is disconnected from the skid control ECU.

·

The brake fluid level is insufficient.

·

The parking brake is applied.

·

EBD operation has been disabled.


WIRING DIAGRAM

C209426E14
0.625,0.583 1.031,0.729 0.406,0.146 10 false CANL 0.615,1.094 1.052,1.24 0.438,0.146 10 false CANH 4.49,2.729 4.896,2.875 0.406,0.146 10 false CANL 4.458,2.063 4.896,2.208 0.438,0.146 10 false CANH 6.198,2.729 6.604,2.875 0.406,0.146 10 false CA1L 6.198,2.052 6.635,2.198 0.438,0.146 10 false CA1H 1.125,0.542 1.552,0.729 0.427,0.188 10 false L201 1.198,0.333 1.417,0.521 0.219,0.188 10 false 13 1.125,1.083 1.615,1.302 0.49,0.219 10 false L201 1.198,0.875 1.396,1.094 0.198,0.219 10 false 14 4.969,1.958 5.146,2.104 0.177,0.146 10 false 19 4.969,2.646 5.146,2.792 0.177,0.146 10 false 20 6.208,3.958 6.458,4.104 0.25,0.146 10 false IG1 6.208,4.688 6.573,4.833 0.365,0.146 10 false LBL 5.917,4.615 6.146,4.802 0.229,0.188 10 false 36 2.135,3.313 2.406,3.458 0.271,0.146 10 false L27 2.458,3.313 4.844,3.594 2.385,0.281 10 false Combination Meter Sub-assembly 2.031,3.938 3.427,4.167 1.396,0.229 10 false from IG1 NO. 1 Relay 4.438,4.083 5.406,4.271 0.969,0.188 10 false ECU-IG NO. 2 5.771,8.177 7,8.563 1.229,0.385 10 false Brake Booster with Master Cylinder 0.51,5.646 0.938,5.854 0.427,0.208 10 false PKB 0.448,5.865 0.677,6.01 0.229,0.146 10 false 12 0.156,8.156 1.208,8.354 1.052,0.198 10 false Main Body ECU 1.188,7.135 1.396,7.323 0.208,0.188 10 false 2C 1.198,6.927 1.406,7.073 0.208,0.146 10 false 20 3.146,5.458 3.281,5.635 0.135,0.177 10 false 2 1.969,7.031 2.063,7.177 0.094,0.146 10 false 1 1.729,5.448 1.823,5.594 0.094,0.146 10 false 1 1.208,6.094 1.479,6.281 0.271,0.188 10 false A32 1.521,6.094 3.635,6.344 2.115,0.25 10 false Brake Fluid Level Warning Switch 1.552,7.448 1.823,7.594 0.271,0.146 10 false A25 1.854,7.448 3.229,7.656 1.375,0.208 10 false Parking Brake Switch 6.198,5.302 6.615,5.448 0.417,0.146 10 false GND 6.208,5.76 6.625,5.906 0.417,0.146 10 false GND2 6.208,6.219 6.625,6.365 0.417,0.146 10 false GND3 6.208,6.667 6.625,6.813 0.417,0.146 10 false GND4 6.208,7.115 6.625,7.26 0.417,0.146 10 false GND5 6.208,7.573 6.625,7.719 0.417,0.146 10 false GND6 5.427,8.188 5.719,8.354 0.292,0.167 10 false A58 1.906,5.448 2.063,5.583 0.156,0.135 10 false + 2.938,5.458 3.115,5.656 0.177,0.198 10 false E 5.927,5.219 6.167,5.396 0.24,0.177 10 false 28 5.927,5.646 6.177,5.844 0.25,0.198 10 false 27 5.927,6.094 6.156,6.281 0.229,0.188 10 false 26 5.927,6.552 6.177,6.74 0.25,0.188 10 false 25 5.938,6.99 6.198,7.156 0.26,0.167 10 false 24 5.938,7.458 6.229,7.656 0.292,0.198 10 false 23 5.927,3.844 6.167,4.01 0.24,0.167 10 false 16 5.917,2.646 6.146,2.854 0.229,0.208 10 false 38 5.927,1.958 6.156,2.167 0.229,0.208 10 false 37 2.146,7.031 2.302,7.167 0.156,0.135 10 false +

CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake booster with master cylinder (skid control ECU), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK DTC
a.

Check if a ABS, VSC and/or electronically controlled brake system DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).


Result:
Result Proceed to
DTC is not output A
DTC is output B



A

2.CHECK CAN COMMUNICATION SYSTEM

B

2.CHECK CAN COMMUNICATION SYSTEM
a.

Result:
Result Proceed to
DTC is not output A
DTC is output B



A

3.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

B

3.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU connector is securely connected.

OK:

The connector is securely connected.




OK

4.CHECK AUXILIARY BATTERY

NG

CONNECT CONNECTOR TO ECU CORRECTLY

4.CHECK AUXILIARY BATTERY
a.

Check the auxiliary battery voltage.

Standard Voltage:

11 to 14 V




OK

5.INSPECT SKID CONTROL ECU (IG1 TERMINAL)

NG

CHARGE OR REPLACE AUXILIARY BATTERY

5.INSPECT SKID CONTROL ECU (IG1 TERMINAL)
a.
U154753E02
1.344,1.865 1.042,2.823 true 0.198,0.188 0.385,0.344 0.188,0.156 10 false *a 0.271,0.875 0.563,1.031 0.292,0.156 10 false A58 0.948,2.844 1.26,3 0.313,0.156 10 false IG1

Disconnect the skid control ECU connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A58-16 (IG1) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



OK

6.INSPECT SKID CONTROL ECU (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

6.INSPECT SKID CONTROL ECU (GND TERMINAL)
a.
U154749E02
2.26,1.802 2.26,1 false 2.365,1.802 2.708,0.667 false 2.146,1.802 1.802,0.667 false 2.469,1.802 3.01,0.979 false 2.052,1.802 1.5,0.979 false 2.646,1.99 2.938,2.76 false 0.198,0.188 0.406,0.344 0.208,0.156 10 false *a 0.271,0.865 0.563,1.021 0.292,0.156 10 false A58 2.031,0.802 2.438,0.958 0.406,0.156 10 false GND4 1.552,0.49 1.958,0.646 0.406,0.156 10 false GND5 2.49,0.49 2.896,0.646 0.406,0.156 10 false GND3 2.813,0.802 3.219,0.958 0.406,0.156 10 false GND2 1.25,0.802 1.656,0.958 0.406,0.156 10 false GND6 2.771,2.781 3.125,2.938 0.354,0.156 10 false GND

Turn the power switch off (lock).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-28 (GND) - Body ground Always Below 1 Ω
A58-27 (GND2) - Body ground Always Below 1 Ω
A58-26 (GND3) - Body ground Always Below 1 Ω
A58-25 (GND4) - Body ground Always Below 1 Ω
A58-24 (GND5) - Body ground Always Below 1 Ω
A58-23 (GND6) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



OK

7.READ VALUE USING GTS (PARKING BRAKE SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

7.READ VALUE USING GTS (PARKING BRAKE SWITCH)
a.

Reconnect the skid control ECU connector.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Select the Data List on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Parking Brake SW Parking brake switch / ON or OFF ON: Parking brake applied
OFF: Parking brake released
-


e.

Using the GTS, check if the switch condition on the GTS changes according to parking brake operation.

OK:

The GTS displays ON or OFF according to parking brake operation.




OK

8.INSPECT COMBINATION METER SUB-ASSEMBLY

NG

9.INSPECT PARKING BRAKE SWITCH
8.INSPECT COMBINATION METER SUB-ASSEMBLY
a.

Turn the power switch off (lock).


b.

Perform the Active Test of the combination meter sub-assembly (meter CPU) using the GTS (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).


c.

Check the combination meter sub-assembly.

OK:

The brake warning light / red (malfunction) turns on or off in accordance with the GTS operation.


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (w/ Multi-information Display) C
NG (w/o Multi-information Display) D


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

REPLACE COMBINATION METER SUB-ASSEMBLY

D

9.INSPECT PARKING BRAKE SWITCH
a.
C211519E03
0.38,0.289 0.545,0.459 0.165,0.170 10 *a 1.766,1.947 0.844,2.799 false 0.746,2.804 0.874,2.974 0.128,0.170 10 +

Turn the power switch off (lock).


b.

Disconnect the parking brake switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (+) - Body ground Parking brake switch ON
(Switch pin free)
Below 1 Ω
1 (+) - Body ground Parking brake switch OFF
(Switch pin pushed in)
10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Parking Brake Switch)

Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

10.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - PARKING BRAKE SWITCH)

B

REPLACE PARKING BRAKE SWITCH

C

REPLACE PARKING BRAKE SWITCH

10.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - PARKING BRAKE SWITCH)
a.

Disconnect the main body ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-20 (PKB) - A25-1 (+) Always Below 1 Ω
2C-20 (PKB) - Body ground Always 10 kΩ or higher


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR