Home › Vehicle Interior › HEATING / AIR CONDITIONING › CONDENSER › from 2020.08
RM2070E _58 Vehicle Interior _061946 HEATING / AIR CONDITIONING _0301846 CONDENSER A

HEATING / AIR CONDITIONING  CONDENSER  INSTALLATION  


PROCEDURE

Hide 88450 1.INSTALL CONDENSER ASSEMBLY WITH RECEIVER

a.

Install the hybrid radiator assembly to the condenser assembly with receiver with the 4 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


b.
E223851

Install the condenser assembly with receiver as shown in the illustration.

HINT:

If the condenser is replaced with a new one, add compressor oil to the new condenser.


Compressor Oil:

ND-11 or equivalent


NOTICE:

Do not use any compressor oil other than ND-OIL 11 or equivalent. If any compressor oil other than ND-OIL 11 or equivalent is used, compressor motor insulation performance may decrease, resulting in leakage of electric power.



Hide 16712 2.INSTALL NO. 2 FAN SHROUD

Hide 53208A 3.INSTALL HOOD LOCK SUPPORT SUB-ASSEMBLY

Hide 88710E 4.CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY

a.

Remove the vinyl tape from the pipe and the connecting part of the condenser assembly with receiver.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the pipe joint.

NOTICE:

Keep the O-ring and O-ring fitting surface clean from dirt or any foreign objects.



c.

Install the O-ring to the air conditioner tube and accessory assembly.

Compressor Oil:

ND-OIL 11 or equivalent


NOTICE:
·

Keep the O-ring and O-ring fitting surface clean from dirt or any foreign objects.

·

Do not use any compressor oil other than ND-OIL 11 or equivalent. If any compressor oil other than ND-OIL 11 or equivalent is used, compressor motor insulation performance may decrease, resulting in leakage of electric power.




d.

Install the air conditioner tube and accessory assembly on the condenser assembly with receiver with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 88711 5.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

a.

Remove the vinyl tape from the hose and the connecting part of the condenser assembly with receiver.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the hose joint.

NOTICE:

Keep the O-ring and O-ring fitting surface clean from dirt or any foreign objects.


Compressor Oil:

ND-OIL 11 or equivalent



c.

Install the O-ring to the No. 1 cooler refrigerant discharge hose.

NOTICE:
·

Keep the O-ring and O-ring fitting surface clean from dirt or any foreign objects.

·

Do not use any compressor oil other than ND-OIL 11 or equivalent. If any compressor oil other than ND-OIL 11 or equivalent is used, compressor motor insulation performance may decrease, resulting in leakage of electric power.




d.

Install the No. 1 cooler refrigerant discharge hose on the condenser assembly with receiver with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide G9225K 6.CONNECT NO. 1 INVERTER COOLING HOSE

a.

Using pliers, grip the claws of the clip and slide the clip to connect the No. 1 inverter cooling hose.

NOTICE:

To prevent entry of foreign matter, do not remove the vinyl tape from the No. 1 inverter cooling hose and condenser assembly with receiver until just before installing the No. 1 inverter cooling hose.



Hide G9229A 7.CONNECT NO. 5 INVERTER COOLING HOSE

a.

Using pliers, grip the claws of the clip and slide the clip to connect the No. 5 inverter cooling hose.

NOTICE:

To prevent entry of foreign matter, do not remove the vinyl tape from the No. 5 inverter cooling hose and condenser assembly with receiver until just before installing the No. 5 inverter cooling hose.



Hide 9.INSTALL FRONT BUMPER ASSEMBLY

Hide 10.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 64995 11.INSTALL DECK FLOOR BOX RH

Hide 64993 12.INSTALL REAR DECK FLOOR BOX

Hide 58412A 13.INSTALL NO. 2 DECK BOARD

Hide 58411A 14.INSTALL NO. 1 DECK BOARD

Hide 58410B 15.INSTALL DECK BOARD ASSEMBLY

Hide 17. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 21.ADJUST HOOD SUB-ASSEMBLY