ELECTRONICALLY CONTROLLED BRAKE SYSTEM > TEST MODE PROCEDURE |
| WARNING LIGHT AND INDICATOR LIGHT INITIAL CHECK |
Release the parking brake.
When the ignition switch is turned to ON (IG), check that the ABS warning, brake warning / red (malfunction), brake warning / yellow (minor malfunction) and slip indicator lights come on until the ignition switch is turned to ON (READY).
| Trouble Area | See Procedure |
| ABS warning light circuit (Remains on) |
Click here
|
| ABS warning light circuit (Does not come on) |
Click here
|
| Brake warning light / red (malfunction) circuit (Remains on) |
Click here
|
| Brake warning light / red (malfunction) circuit (Does not come on) |
Click here
|
| Brake warning light / yellow (minor malfunction) circuit (Remains on) |
Click here
|
| Brake warning light / yellow (minor malfunction) circuit (Does not come on) |
Click here
|
| Slip indicator light circuit (Remains on) |
Click here
|
| Slip indicator light circuit (Does not come on) |
Click here
|
| SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (When Using the Techstream) |
Procedure to enter Test Mode
Turn the ignition switch off.
Check that the steering wheel is centered.
Check that the parking brake is released.
Check that the shift lever is in P.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Turn the Techstream on.
Switch the skid control ECU to Test Mode using the Techstream. Enter the following menus: Chassis / ABS/VSC/TRAC / Utility / Signal Check.
Check that the ABS warning, brake warning / yellow (minor malfunction) and slip indicator lights come on for several seconds and then blink in the Test Mode pattern.
Check the ABS sensors.
Acceleration Sensor Check
Keep the vehicle stationary on a level surface for 2 second or more.
Master Cylinder Pressure Sensor Check
Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and quickly and continuously depress the brake pedal with a force greater than 98 N (10 kgf, 22.0 lbf) for 1 second.
Check that the ABS warning light stays on for 3 seconds.
Speed Sensor Check
Drive the vehicle straight-ahead.
Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds and check that the ABS warning light goes off.
Stop the vehicle.
End of Sensor Check
When the sensor checks have completed, the ABS warning light goes off while driving, and blinks in the Test Mode pattern while the vehicle is stopped.
Reading Sensor Check DTCs
Read the DTC(s) by following the Techstream screen.
Turn the ignition switch off and disconnect the Techstream.
Sensor Check DTCs
| DTC No. | Detection Item | Trouble Area |
| C1271 | Low Output Signal of Front Speed Sensor RH |
|
| C1272 | Low Output Signal of Front Speed Sensor LH |
|
| C1273 | Low Output Signal of Rear Speed Sensor RH |
|
| C1274 | Low Output Signal of Rear Speed Sensor LH |
|
| C1275 | Abnormal Change in Output Signal of Front Speed Sensor RH |
|
| C1276 | Abnormal Change in Output Signal of Front Speed Sensor LH |
|
| C1277 | Abnormal Change in Output Signal of Rear Speed Sensor RH |
|
| C1278 | Abnormal Change in Output Signal of Rear Speed Sensor LH |
|
| C1279 | Acceleration Sensor Output Voltage Malfunction |
|
| C1281 | Master Cylinder Pressure Sensor Output Malfunction |
|
| DTC No. | Detection Item | Trouble Area |
| C1346 | Stroke Sensor Zero Point Learning Malfunction |
|
| SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (When not Using the Techstream) |
Procedure to enter Test Mode
Turn the ignition switch off.
Check that the steering wheel is centered.
Check that the parking brake is released.
Check that the shift lever is in P.
![]() |
Using SST, connect terminals TS and CG of the DLC3.
| *a | Front view of DLC3 |
Turn the ignition switch to ON (IG).
Check that the ABS warning, brake warning / yellow (minor malfunction) and slip indicator lights come on for several seconds and then blink in the Test Mode pattern.
Check the ABS sensors.
Acceleration Sensor Check
Keep the vehicle stationary on a level surface for 2 second or more.
Master Cylinder Pressure Sensor Check
Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and quickly and continuously depress the brake pedal with a force greater than 98 N (10 kgf, 22.0 lbf) for 1 second.
Check that the ABS warning light stays on for 3 seconds.
Speed Sensor Check
Drive the vehicle straight-ahead.
Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds and check that the ABS warning light goes off.
Stop the vehicle.
End of Sensor Check
When the sensor checks have completed, the ABS warning light goes off while driving, and blinks in the Test Mode pattern while the vehicle is stopped.
Reading Sensor Check DTCs
![]() |
Using SST, connect terminals TC and CG of the DLC3.
| *a | Front view of DLC3 |
Count the number of blinks of the ABS warning, brake warning / yellow (minor malfunction) and slip indicator lights.
After performing the check, disconnect SST from terminals TS and CG, and TC and CG of the DLC3 and turn the ignition switch off.
Sensor Check DTCs
| DTC No. | Detection Item | Trouble Area |
| 71 | Low Output Signal of Front Speed Sensor RH |
|
| 72 | Low Output Signal of Front Speed Sensor LH |
|
| 73 | Low Output Signal of Rear Speed Sensor RH |
|
| 74 | Low Output Signal of Rear Speed Sensor LH |
|
| 75 | Abnormal Change in Output Signal of Front Speed Sensor RH |
|
| 76 | Abnormal Change in Output Signal of Front Speed Sensor LH |
|
| 77 | Abnormal Change in Output Signal of Rear Speed Sensor RH |
|
| 78 | Abnormal Change in Output Signal of Rear Speed Sensor LH |
|
| 79 | Acceleration Sensor Output Voltage Malfunction |
|
| 81 | Master Cylinder Pressure Sensor Output Malfunction |
|
| DTC No. | Detection Item | Trouble Area |
| 71 | Stroke Sensor Zero Point Learning Malfunction |
|