SMART KEY SYSTEM (for Start Function) > Power Source Mode does not Change to ON (READY) |
| Problem Symptom | Data List Item | Active Test Item |
| Power source mode does not change to ON (READY) | Power Source Control
Smart Key
| - |
| 1.CHECK HYBRID CONTROL SYSTEM (READY ON) |
Place the electrical key transmitter sub-assembly on the driver seat.
Depress the brake pedal.
Confirm that the smart warning light is displayed, and then press the power switch and check that the hybrid system turns on (READY).
|
| ||||
| OK | ||
| ||
| 2.CHECK AUXILIARY BATTERY |
Measure the auxiliary battery voltage with the power switch off.
| NEXT | |
| 3.CHECK FOR DTC (ALL) |
Using the Techstream, confirm the output of DTCs for all systems.
|
| ||||
| OK | |
| 4.CHECK WAVE ENVIRONMENT |
If the problem occurs in certain locations or times of day, the possibility of wave interference is high.
| NEXT | |
| 5.CHECK POWER SWITCH CONDITION |
Get into the vehicle while carrying an electrical key transmitter sub-assembly.
Move the shift lever to P.
With the brake pedal released, check that pressing the power switch causes the power source mode to change.
| Result | Proceed to |
| Off → on (ACC) → on (IG) → off | A |
| Power source mode does not change to on (ACC) and on (IG) | B |
| Power source mode changes to on (IG) but not to on (ACC) | C |
| Power source mode changes to on (ACC) but not to on (IG) | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 6.READ VALUE USING TECHSTREAM (STEERING UNLOCK SWITCH) |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Steering Unlock Switch | State of steering unlock sensor signal output from steering lock actuator assembly/ON or OFF | ON: Steering unlocked OFF: Steering locked |
|
|
| ||||
| OK | |
| 7.READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH1) |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Stop Light Switch1 | State of brake pedal/ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released |
|
|
| ||||
| OK | |
| 8.READ VALUE USING TECHSTREAM (L CODE CHECK) |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Body Electrical / Smart Key / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| L Code Check | w/o ID Code Box (Immobiliser Code ECU): Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly)/OK or NG w/ ID Code Box (Immobiliser Code ECU): Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator assembly)/OK or NG | OK: Verification result normal NG: Verification result abnormal |
|
|
| ||||
| OK | |
| 9.READ VALUE USING TECHSTREAM (STARTER REQUEST SIGNAL) |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Body Electrical / Smart Key / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Engine Start Condition | Status of hybrid control system start permission signal determined by steering lock ECU (steering lock actuator assembly) and sent to certification ECU (smart key ECU assembly)/ OK or NG | OK: Hybrid control system start permitted NG: Hybrid control system start prohibited |
|
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | ||
| ||
| 10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SOURCE AND BODY GROUND) |
![]() |
Disconnect the A65 stop light switch assembly connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A65-1 (B) - A65-3 (GND) | Engine switch off | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
| A65-3 (GND) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Stop Light Switch Assembly) |
|
| ||||
| OK | |
| 11.INSPECT STOP LIGHT SWITCH ASSEMBLY |
![]() |
Reconnect the A65 stop light switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A65-2 (OUT) - A65-3 (GND) | Engine switch off, brake pedal not depressed | Below 1 V |
| A65-2 (OUT) - A65-3 (GND) | Engine switch off, brake pedal depressed | 11 to 14 V |
| *a | Component with harness connected (Stop Light Switch Assembly) |
|
| ||||
| OK | |
| 12.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY) |
Disconnect the A65 connector from the stop light switch assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A39-23 (STP) - A65-2 (OUT) | Always | Below 1 Ω |
| A39-23 (STP) or A65-2 (OUT) - Body ground | Always | 10 kΩ or higher |
Reconnect the A65 stop light switch assembly connector.
![]() |
Disconnect the A39 connector from the power management control ECU.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A39-23 (STP) - Body ground | Brake pedal released | 1 V or less |
| Brake pedal depressed | 9 V or higher |
| *a | Front view of wire harness connector (to Power Management Control ECU) |
|
| ||||
| OK | ||
| ||
| 13.CHECK STEERING LOCK ACTUATOR ASSEMBLY |
Replace the steering lock ECU (steering lock actuator assembly) with a new one (Click here).
Perform the registration procedures (Refer to the Service Bulletin).
| NEXT | |
| 14.CHECK HYBRID CONTROL SYSTEM (READY ON) |
Place the electrical key transmitter sub-assembly on the driver seat.
Depress the brake pedal.
Confirm that the smart warning light is displayed, and then press the power switch and check that the hybrid system turns on (READY).
|
| ||||
| OK | ||
| ||
| 15.READ VALUE USING TECHSTREAM (S CODE CHECK) |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Body Electrical / Smart Key / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| S Code Check | Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU)/OK or NG | OK: Verification result normal NG: Verification result abnormal |
|
|
| ||||
| OK | |
| 16.CHECK ENGINE IMMOBILISER SYSTEM |
![]() |
Measure the voltage according to the value(s) in the table below.
| *a | Component with harness connected (Power Management Control ECU) |
Waveform 1

| *a | Approximately 160 ms | *b | Approximately 270 ms |
| Item | Content |
| Tester Connection | G58-20 (IMO) - G57-6 (E1) |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected |
Waveform 2

| *a | Approximately 160 ms | *b | Approximately 270 ms |
| Item | Content |
| Tester Connection | G58-21 (IMI) - G57-6 (E1) |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected |
|
| ||||
| OK | |
| 17.READ VALUE USING TECHSTREAM (STARTER REQUEST SIGNAL) |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Starter Request Signal | Hybrid control system start request signal status/ON or OFF | ON: With the shift lever in P and brake pedal depressed, the power switch is pressed and held OFF: After approx. 1 sec. has elapsed, the power switch is released |
|
|
| ||||
| OK | ||
| ||
| 18.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Replace the certification ECU (smart key ECU assembly) with a new one (Click here).
Perform the registration procedures (Click here).
| NEXT | |
| 19.CHECK HYBRID CONTROL SYSTEM (READY ON) |
Place the electrical key transmitter sub-assembly on the driver seat.
Depress the brake pedal.
Confirm that the smart warning light is displayed, and then press the power switch and check that the hybrid system turns on (READY).
|
| ||||
| OK | ||
| ||
| 20.CHECK AND REPLACE HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ID CODE BOX (IMMOBILISER CODE ECU)) |
Disconnect the G58 connector from the power management control ECU.
Disconnect the G49 connector from the ID code box (immobiliser code ECU).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G58-20 (IMO) - G49-3 (EFII) | Always | Below 1 Ω |
| G58-21 (IMI) - G49-4 (EFIO) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 21.REPLACE POWER MANAGEMENT CONTROL ECU |
Replace the power management control ECU with a new one (Click here).
| NEXT | |
| 22.CHECK HYBRID CONTROL SYSTEM (READY ON) |
Place the electrical key transmitter sub-assembly on the driver seat.
Depress the brake pedal.
Confirm that the smart warning light is displayed, and then press the power switch and check that the hybrid system turns on (READY).
|
| ||||
| OK | ||
| ||