Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

AIRBAG SYSTEM > SRS Warning Light Remains ON

for Preparation Click here


DESCRIPTION

The SRS warning light is located on the combination meter assembly.
When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off to ON (IG), and then goes off automatically.
If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.
When terminals TC and CG of the DLC3 are connected, the DTC is displayed by blinking of the SRS warning light.
The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the airbag sensor assembly in case the source voltage drops.
When the auxiliary battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage. In addition, when the voltage drops, the SRS warning light will illuminate.
A malfunction in this circuit is not stored in the airbag sensor assembly. The SRS warning light automatically goes off when the source voltage returns to normal.
The signal to illuminate the SRS warning light is transmitted from the airbag sensor assembly to the combination meter assembly through the CAN communication system.

WIRING DIAGRAM


C249367E04


INSPECTION PROCEDURE

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK SRS WARNING LIGHT OPERATION
  1. Check the SRS warning light operation approximately 6 seconds after the ignition switch is turned to ON (IG).

    Result:
    SRS Warning Light Illumination
    Proceed to
    Remains on
    A
    Goes off and then comes on again
    B



B
Go to step 6
A


2.CHECK AUXILIARY BATTERY VOLTAGE
  1. Measure the voltage of the auxiliary battery.

    Standard Voltage:
    11 to 14 V



NG
INSPECT CHARGING SYSTEM AND AUXILIARY BATTERY (Click here)
OK


3.CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Check that the connector is properly connected to the airbag sensor assembly.

    OK:
    The connector is properly connected.

    HINT:
    If the connector is not connected securely, reconnect the connector and proceed to the next inspection.

  1. Disconnect the connector from the airbag sensor assembly.

  1. Check that the terminal of the connector is not damaged.

    OK:
    The terminal is not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


4.CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - BODY GROUND)


    C126715E09
  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the ignition switch to ON (IG).

  1. Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G18-21 (IG2) - Body ground
    Ignition switch ON (IG)
    8 to 16 V

  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G18-25 (E1) - Body ground
    Always
    Below 1 Ω
    G18-26 (E2) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Airbag Sensor Assembly)



NG
REPLACE WIRE HARNESS
OK


5.CHECK SRS WARNING LIGHT
  1. Turn the ignition switch to ON (IG).

  1. Check the SRS warning light condition.

    OK:
    After the primary check period, the SRS warning light goes off for approximately 10 seconds and turns back on.

    HINT:
    The primary check period is approximately 6 seconds after the ignition switch is turned to ON (IG).



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE AIRBAG SENSOR ASSEMBLY (Click here)  

6.CHECK CAN COMMUNICATION SYSTEM
  1. Use the Techstream to check if the CAN communication system is functioning normally.

    HINT:
    1. Refer to Bus Check for the CAN communication system (Click here).
    2. The airbag sensor assembly is connected to the CAN communication system. Therefore, before starting troubleshooting, make sure to check that there is no trouble in the CAN communication system.

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


7.CHECK AUXILIARY BATTERY VOLTAGE
  1. Measure the voltage of the auxiliary battery.

    Standard Voltage:
    11 to 14 V



NG
INSPECT CHARGING SYSTEM AND AUXILIARY BATTERY (Click here)
OK


8.CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Check that the connector is properly connected to the airbag sensor assembly.

    OK:
    The connector is properly connected.

    HINT:
    If the connector is not connected securely, reconnect the connector and proceed to the next inspection.

  1. Disconnect the connector from the airbag sensor assembly.

  1. Check that the terminal of the connector is not damaged.

    OK:
    The terminal is not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


9.CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - BODY GROUND)


    C126715E09
  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the ignition switch to ON (IG).

  1. Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G18-21 (IG2) - Body ground
    Ignition switch ON (IG)
    8 to 16 V

  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G18-25 (E1) - Body ground
    Always
    Below 1 Ω
    G18-26 (E2) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Airbag Sensor Assembly)



NG
REPLACE WIRE HARNESS
OK


10.CHECK CONNECTOR
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Check that the connector is properly connected to the combination meter assembly.

    OK:
    The connector is properly connected.

    HINT:
    If the connector is not connected securely, reconnect the connector and proceed to the next inspection.

  1. Disconnect the connector from the combination meter assembly.

  1. Check that the terminal of the connector is not damaged.

    OK:
    The terminal is not deformed or damaged.



NG
REPAIR OR REPLACE CONNECTOR
OK


11.CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)


    C241761E07
  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the ignition switch to ON (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G1-21 (IG+) - Body ground
    Ignition switch ON (IG)
    11 to 14 V
    G1-1 (B) - Body ground
    Ignition switch off
    11 to 14 V

  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G1-20 (ET) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly)



NG
REPAIR OR REPLACE WIRE HARNESS
OK


12.CHECK SRS WARNING LIGHT
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Connect the connector to the combination meter assembly.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the ignition switch to ON (IG).

  1. Check the SRS warning light condition.

    OK:
    After the primary check period, the SRS warning light goes off for approximately 10 seconds and turns back on.

    HINT:
    The primary check period is approximately 6 seconds after the ignition switch is turned to ON (IG).



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE AIRBAG SENSOR ASSEMBLY (Click here)