Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > DIAGNOSIS SYSTEM

for Preparation Click here



ECUS OR SENSORS WHICH COMMUNICATE THROUGH CAN COMMUNICATION SYSTEM
  1. V Bus

    1. ECM

    2. Brake booster with master cylinder assembly (Skid control ECU)

    3. Main body ECU (Multiplex network body ECU)

    4. Air conditioning amplifier assembly

    5. Power steering ECU assembly

    6. Smart key ECU assembly (Certification ECU)*1

    7. Airbag sensor assembly

    8. Spiral cable with sensor sub-assembly (Steering sensor)

    9. Power management control ECU

    10. Combination meter assembly

    11. Radio and display receiver assembly*2

      HINT:
      1. *1: w/ Smart key system
      2. *2: for Radio and display type

  2. Sub Bus 15

    1. ECM

    2. Power management control ECU

    3. Brake booster with master cylinder assembly (Skid control ECU)


CHECK FOR INSTALLED SYSTEMS (ECUS AND SENSORS) THAT ADOPT CAN COMMUNICATION
  1. The systems (ECUs and sensors) that adopt CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed on the vehicle.

    HINT:
    The names of ECUs and sensors shown on the Techstream display may differ from those shown in the DTC Table by ECU section that follows.


    ECU/Sensor Name
    Techstream Display
    Applicability
    ECM
    ECM (Engine)
    Installed on all vehicles
    Main body ECU (Multiplex network body ECU)
    Main Body
    Installed on all vehicles
    Brake booster with master cylinder assembly
    (Skid control ECU)
    Skid Control (ABS/VSC/TRAC)
    Installed on all vehicles
    Power steering ECU assembly
    Power Steering (EPS)
    Installed on all vehicles
    Air conditioning amplifier assembly
    Air Conditioning Amplifier
    Installed on all vehicles
    Airbag sensor assembly
    Airbag
    Installed on all vehicles
    Smart key ECU assembly
    (Certification ECU)
    Certification (Smart)
    Vehicles with smart key system
    Power management control ECU
    1. Hybrid Vehicle Control
    2. Power management2
    Installed on all vehicles
    Spiral cable with sensor sub-assembly (Steering sensor)
    Spiral cable (Steering Angle Sensor)
    Installed on all vehicles
    Combination meter assembly
    Combination Meter
    Installed on all vehicles
    Radio and display receiver assembly
    Display and Navigation (AVN1)
    Vehicles with radio and display receiver assembly


CAN BUS CHECK

HINT:
The ECUs and sensors that are properly connected to the CAN communication system can be displayed using the Techstream.

  1. Using the Techstream, select "CAN Bus Check" from "System Select".

    NOTICE:
    1. It may be possible to select buses that do not have ECUs or sensors from the bus selection pull down menu. This is not a malfunction. (This occurs when optional devices are not on a sub bus that is monitored by a gateway function equipped ECU.)
    2. In the bus selection pull down menu, all buses applicable to the model are displayed (e.g. LIN communication buses are also displayed). Therefore, refer to the wiring diagrams to check the names of sub buses for CAN communication (Click here).

    HINT:
    Different connection statuses are indicated by the background color of ECUs and sensors that are displayed.

    Explanation of CAN Bus Check (Communication Bus Check) screen 
    Bus Type
    Background Color
    Connection Status
    V Bus
    White
    Communication has been normal since the start of the CAN bus check.
    Yellow
    Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
    Red
    Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).
    Not displayed
    Communication stop has continued since the start of the CAN bus check.*1
    Sub bus
    (gateway function equipped ECU that does not have history of connected ECUs)*2
    White
    Communication has been normal since the start of the CAN bus check.
    Yellow
    Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
    Red
    Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).
    Not displayed
    Communication stop has continued since the start of the CAN bus check.*1
    Sub bus
    (gateway function equipped ECU that has history of connected ECUs)*3
    White
    Communication has been normal since the start of the CAN bus check.
    Yellow
    Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
    Red
    Currently not communicating (either of the following):
    1. Communication stop has continued since the start of the CAN bus check
    2. Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring
    Not displayed
    Either of the following:
    1. If a gateway function equipped ECU cannot communicate, the sub bus and ECUs connected to the sub bus will not be displayed.
    2. If no ECUs are connected to the sub bus, "There is no system found on the Communication Bus" will be displayed.

    HINT:
    1. Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
    2. *1: ECUs that are present in the vehicle but are not displayed on CAN Bus Check.
    3. *2: Gateway function equipped ECU that does not memorize the sub bus ECUs that are connected to it.
    4. *3: Gateway function equipped ECU that memorizes the sub bus ECUs that are connected to it.
    5. If none of the connected ECUs are displayed, or there is no response from the vehicle to the Techstream, check the DLC3 branch and the V bus main bus lines for a malfunction.

  2. Observe the connection response screen for approximately 2 minutes to check for a change in connection status of the connected ECUs and sensors.

    HINT:
    1. If an open occurs in one of the lines of a CAN branch (except DLC3), output from the other branch line (the line that is not open) will be unstable and it may interfere the response (display) of other ECUs and sensors.
    2. If the connection status changes during the inspection, repair the open in the branch line of the ECU or sensor that does not respond (is not detected) and then perform the CAN bus check again.


HOW TO INTERPRET CAN BUS CHECK (COMMUNICATION BUS CHECK) SCREEN
  1. When a communication stop is currently occurring, the probable malfunctioning part can be determined from the CAN bus check and by using the following methods.

    NOTICE:
    The following CAN bus wiring diagram is provided only as an example. This wiring diagram is different from the actual wiring diagram for this vehicle.

    HINT:
    1. When a communication stop is currently occurring, it is easier to determine the probable malfunctioning part from the CAN bus check rather than from communication DTCs.
    2. Wait for approximately 2 minutes after turning the ignition switch ON (or simulate the driving conditions that enable the malfunction to be reproduced) and select the CAN bus check. Then observe the communication status of each ECU on the screen.



  2. If a communication error of only 1 ECU or sensor is indicated on the CAN Bus Check screen, a communication stop of the ECU or sensor is suspected.
    Example: Open in both CAN branch lines of ECU B on the V bus


    C240692E01


    Text in Illustration 
    *a
    V Bus
    *b
    Sub Bus
    *c
    Terminating Resistor
    *d
    Location of malfunction
    *e
    Not displayed or background color changes to red or yellow
    *f
    CAN Bus Check screen

    HINT:
    When there are communication stops, ECUs are present in the vehicle even though they are not displayed on the CAN Bus Check screen.



  3. C240693E01
  4. If communication errors for multiple ECUs or sensors are indicated on the CAN Bus Check screen, then a communication stop of the ECU or sensor that shows a more serious communication stop (an ECU or a sensor which is not displayed) is suspected.
    Example: Open in a CAN branch line for ECU D on the V bus
    Text in Illustration 
    *a
    Background color periodically changes to yellow or red
    *b
    Not displayed or background color is yellow or red
    *c
    Not displayed
    Explanation of CAN Bus Check (Communication Bus Check) screen 
    Bus Type
    Background Color
    Connection Status
    V Bus
    White
    Communication has been normal since the start of the CAN bus check.
    Yellow
    Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
    Red
    Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).
    Not displayed
    Communication stop has continued since the start of the CAN bus check.*1
    Sub bus
    (gateway function equipped ECU that does not have history of connected ECUs)*2
    White
    Communication has been normal since the start of the CAN bus check.
    Yellow
    Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
    Red
    Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).
    Not displayed
    Communication stop has continued since the start of the CAN bus check.*1
    Sub bus
    (gateway function equipped ECU that has history of connected ECUs)*3
    White
    Communication has been normal since the start of the CAN bus check.
    Yellow
    Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
    Red
    Currently not communicating (either of the following):
    1. Communication stop has continued since the start of the CAN bus check
    2. Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring
    Not displayed
    Either of the following:
    1. If a gateway function equipped ECU cannot communicate, sub bus and ECUs connected to the sub bus will not be displayed.
    2. If no ECUs are connected to the sub bus, "There is no system found on the Communication Bus" will be displayed.

    HINT:
    1. Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
    2. *1: ECUs that are present in the vehicle but are not displayed on the CAN Bus Check screen.
    3. *2: Gateway function equipped ECU that does not memorize the sub bus ECUs that are connected to it.
    4. *3: Gateway function equipped ECU that memorizes the sub bus ECUs that are connected to it.
    5. The example of the CAN Bus Check screen in the illustration shows the result of electrical noise on the CAN bus which is caused by an open in a CAN branch line of ECU D (output from the other branch line is unstable) and the communication of ECU C is also unstable. In addition, in this example, ECU C is equipped with a gateway function. Therefore, communication is also unstable between the sub bus ECUs of ECU C and the V bus.
    6. The example in the illustration shows that ECU D is not displayed on the CAN Bus Check screen. This indicates a more significant communication stop. In this case, a communication stop of ECU D is suspected.



  5. C240694E01
  6. If a communication error is indicated on both the V bus and sub bus on the CAN Bus Check screen, suspect any communication stop displayed for the V bus first.
    Example: Open in both CAN branch lines of ECU C on the V bus
    Text in Illustration 
    *a
    Not displayed or background color changes to red

    HINT:
    1. In the CAN bus check, it is possible to confirm the communication status of ECUs connected to the V bus after connecting the Techstream to the DLC3. As for sub buses, it is possible to confirm which sub bus connected ECUs can communicate with a gateway function equipped ECU on the V bus.
    2. If a gateway function equipped ECU has a communication error, ECUs connected to the gateway function equipped ECU are also affected, and communication stops will be indicated.
    3. The CAN Bus Check screen in the illustration shows that ECU C has a gateway function and a communication stop in ECU C is suspected.



  7. C240695E01
  8. If the CAN Bus Check screen indicates a communication stop only in the sub bus, a communication stop in the sub bus is suspected.
    Example: Open in both CAN branch lines of ECU G on the sub bus
    Text in Illustration 
    *a
    Background color changes to red

    HINT:
    1. A communication error in a sub bus does not affect the V bus or other buses.
    2. When a gateway function equipped ECU has memorized the ECUs that are connected to the sub bus, if any of the ECUs connected to the gateway function equipped ECU has a communication error, the background color changes to yellow or red. (The displayed name will not disappear.)



  9. If both of the V bus main bus lines are open, ECUs or sensors that are located farther away from the DLC3 than the open part will be displayed as a communication stop on the CAN Bus Check screen.
    (In this case, ECU A and B are not displayed or their background color changes to red.)


    C240696E01


    Text in Illustration 
    *a
    V Bus
    *b
    Sub Bus
    *c
    Terminating Resistor
    *d
    Location of malfunction
    *e
    Not displayed or background color is red
    *f
    CAN Bus Check screen

    HINT:
    If a communication error occurs in an ECU, it is not displayed on the CAN Bus Check screen even though the ECU is present.



  10. If both of the sub bus main bus lines are open, ECUs that are located farther away from the gateway function equipped ECU than the open part will be displayed as a communication stop on the CAN Bus Check screen.
    (In this case, ECU I and J are not displayed or their background color changes to red.)


    C240697E01


    Text in Illustration 
    *a
    V Bus
    *b
    Sub Bus
    *c
    Terminating Resistor
    *d
    Location of malfunction
    *e
    Not displayed or background color is red
    *f
    CAN Bus Check screen
    *g
    Gateway function equipped ECU
    -
    -



  11. C240698E01
  12. When any of the following malfunctions occur, CAN communication cannot be established and almost all ECUs and sensors on the bus show a communication error on the CAN Bus Check screen.
    Text in Illustration 
    *a
    When any of the following malfunctions occur on the V bus
    *b
    When any of the following malfunctions occur on a sub bus
    *c
    Not displayed
    Details of Malfunction 
    Short between CAN lines (CANH and CANL)
    Short between a CAN line (CANH or CANL) and +B
    Short between a CAN line (CANH or CANL) and ground
    Open in a CAN main bus line

    HINT:
    1. When a malfunction occurs on the V bus, almost all ECUs and sensors on the V bus and sub bus indicate a communication error (almost all ECUs are not displayed). As communication with the gateway function equipped ECU that is connected to the V bus stops, communication from the ECUs connected to the sub bus that is monitored by the gateway function equipped ECU also stops (these ECUs are not displayed).
    2. When a malfunction occurs in a sub bus, almost all ECUs connected to the sub bus indicate a communication error.
    3. A communication error in a sub bus does not affect the V bus or other buses.
    4. The malfunctioning part can be determined by checking for a short circuit between CAN bus lines or between a CAN bus line and ground or +B short using an electrical tester.


HOW TO INTERPRET COMMUNICATION DTCS (DTCS THAT START WITH U)


  1. If a CAN communication error cannot be reproduced, determine the suspected malfunctioning part using the DTCs stored in ECUs that are connected to the CAN buses by following the procedure below.

    HINT:
    Communication DTCs (DTCs that start with U) indicate a communication error between the ECU that stores the DTC and the ECU that is indicated by the DTC.




    1. If multiple ECUs store a communication DTC for a particular ECU, a communication stop of the ECU is suspected.


      C240699E01


      Text in Illustration 
      *a
      Items to be checked
      -
      -

      NOTICE:
      1. This DTC table is from another model, and is only used here to show an example of DTCs that are output when there is an open in a CAN branch line for the main body ECU. This table does not show DTCs applicable to this vehicle.
      2. Even though a DTC title may indicate a communication error with a specific ECU, the ECU name used in the DTC name on the Techstream may differ depending on the ECU that stores the DTC. (Regarding output DTCs, refer to step 6 and the DTC chart for each ECU.)

      HINT:
      As multiple ECUs indicate a communication stop with the main body ECU, the possibility of a communication stop of the main body ECU is high.



    2. If almost all of the communication DTCs of an ECU are stored, a communication stop of the ECU is suspected.


      C240700E01


      Text in Illustration 
      *a
      Items to be checked
      -
      -

      NOTICE:
      This DTC table is from another model, and is only used here to show an example of DTCs that are output when there is an open in a CAN branch line for the main body ECU. This table does not show DTCs applicable to this vehicle.

      HINT:
      If almost all of the DTCs of the main body ECU are stored, the possibility of a communication stop of the main body ECU is high.

    3. When a CAN communication error occurs, many DTCs are output. DTCs other than communication error DTCs (such as DTCs that start with C or B) and communication DTCs for the ABS system are important DTCs, however it may be easier to determine the malfunctioning part by examining the overall situation without considering these DTCs.



  2. To help determine the part of the sub bus that has a communication error, prioritize the communication stop DTCs stored in the gateway function equipped ECU.


    C240701E01


    Text in Illustration 
    *a
    Items to be checked
    *b
    ECM
    *c
    Gateway function equipped ECU
    *d
    Location of malfunction
    *e
    V Bus
    *f
    Sub Bus

    NOTICE:
    This DTC table is from another model, and is only used here to show the ECUs connected to both a V bus and a sub bus. It shows DTCs output when there is an open in the main bus lines for the ECM on the sub bus. This table does not show DTCs applicable to this vehicle.

    HINT:
    1. As gateway function equipped ECUs (sub bus monitor ECU) monitor signals from all ECUs that are connected to sub buses, gateway function equipped ECUs can detect ECUs with a communication stop more accurately.
    2. When there is a communication stop for the gateway function equipped ECU (gateway), communication with ECUs connected to other buses such as the V bus stops. Therefore, communication DTCs for ECUs connected to other buses are also stored.

  3. When any of the following malfunctions occurs, many DTCs are likely to be output from many ECUs. Because of this, it may be difficult to determine the probable malfunctioning part.

    1. Short between CAN lines (CANH and CANL)
    2. Short between a CAN line (CANH or CANL) and ground
    3. Short between a CAN line (CANH or CANL) and +B
    4. Open in a CAN branch line (CANH or CANL) of an ECU or sensor
    5. Open in a CAN main bus line (CANH or CANL) between 2 ECUs that have a terminating resistor


DTC TABLE BY ECU

HINT:
  1. In the CAN communication system, the CAN communication DTCs of each ECU can be displayed using the Techstream.
  2. If CAN communication system DTCs are output, trouble cannot be determined only by the DTCs. Perform troubleshooting according to How to Proceed with Troubleshooting (Click here).
  3. If system function temporarily returns to normal, DTCs may not be output again even though the following DTC check procedures are used.

  1. Power Management Control ECU / Techstream Display "Hybrid Control"

    HINT:
    1. This ECU uses the CAN communication system for DTC communication.
    2. *1: Refer to Hybrid Control System (Click here).
    3. *2: Refer to Hybrid Battery System (Click here).
    4. *3: w/o Smart Key System.
    5. *4: w/ Smart Key System.


    Power Management Control ECU / Techstream Display "Hybrid Control" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0100
    Lost Communication with ECM / PCM "A"
    The power management control ECU (HV CPU) does not receive data from the ECM for 0.58 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG) for 1 second or more.
    2. The power source voltage of the power management control ECU is 9.5 V or more.
    Turn the ignition switch ON (IG) and wait 1.58 seconds or more.
    1. Master warning light turns on.
    2. MIL illuminates.
    DTC is stored until it is cleared using the Techstream.
    U0110*1
    Lost Communication with Drive Motor Control Module "A"
    Either condition is met:
    1. The power management control ECU (HV CPU) does not receive data from the inverter with converter assembly (MG ECU) for 0.12 seconds or more.
    2. The power management control ECU (HV CPU) does not send data to the inverter with converter assembly (MG ECU) for 0.04 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG) for 0.1 seconds or more.
    2. The power source voltage of the power management control ECU is 9.5 V or more.
    Turn the ignition switch ON (IG) and wait 0.22 seconds or more.
    Master warning light turns on.
    DTC is stored until it is cleared using the Techstream.
    U0129
    Lost Communication with Brake System Control Module
    The power management control ECU (HV CPU) does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 2.34 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG) for 2.1 seconds or more.
    2. The power source voltage of the power management control ECU is 9.5 V or more.
    Turn the ignition switch ON (IG) and wait 4.44 seconds or more.
    1. Master warning light turns on.
    2. Brake warning light / yellow (minor malfunction) illuminates.
    DTC is stored until it is cleared using the Techstream.
    U0140*3
    Communication Error from Body ECU to HV ECU
    The power management control ECU (HV CPU) does not receive data from the multiplex network body ECU for 3.6 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG) for 1 second or more.
    2. The power source voltage of the power management control ECU is 9.5 V or more.
    Turn the ignition switch ON (IG) and wait 4.6 seconds or more.
    Master warning light turns on.
    DTC is stored until it is cleared using the Techstream.
    U0151
    Communication Error from Airbag ECU to HV ECU
    The power management control ECU (HV CPU) does not receive data from the airbag sensor assembly for 10.6 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG) for 1 second or more.
    2. The power source voltage of the power management control ECU is 9.5 V or more.
    Turn the ignition switch ON (IG) and wait 11.6 seconds or more.
    Master warning light turns on.
    DTC is stored until it is cleared using the Techstream.
    U0164
    Communication Error from A/C ECU to HV ECU
    The power management control ECU (HV CPU) does not receive data from the air conditioning amplifier assembly for 10.6 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG) for 1 second or more.
    2. The power source voltage of the power management control ECU is 9.5 V or more.
    Turn the ignition switch ON (IG) and wait 11.6 seconds or more.
    -
    DTC is stored until it is cleared using the Techstream.
    U029A*2
    Lost Communication with Hybrid Battery Pack Sensor Module
    The power management control ECU (HV CPU) does not receive data from the battery smart unit for 0.52 seconds or more.
    The ignition switch is turned ON (IG) for 0.5 seconds or more.
    Turn the ignition switch ON (IG) and wait 1.02 second or more.
    1. Master warning light turns on.
    2. MIL illuminates.
    DTC is stored until it is cleared using the Techstream.
    U0424*1
    Invalid Data Received from HVAC Control Module
    The power management control ECU (HV CPU) receives an abnormal operation value command from the air conditioning amplifier assembly for 3 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG) for 0.5 seconds or more.
    2. The power source voltage of the power management control ECU is 9.5 V or more.
    Turn the ignition switch ON (IG) and wait 3.5 seconds or more.
    -
    DTC is stored until it is cleared using the Techstream.
    U1107*4
    Lost Communication with Power Management Module
    The power management control ECU (HV CPU) does not receive data from the power management control ECU (power management CPU) for 3.6 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG) for 1 second or more.
    2. The power source voltage of the power management control ECU is 9.5 V or more.
    Turn the ignition switch ON (IG) and wait 4.6 seconds or more.
    Master warning light turns on.
    DTC is stored until it is cleared using the Techstream.

  2. Power Management Control ECU / Techstream Display "Power Source Control"

    HINT:
    1. This ECU uses the CAN communication system for DTC communication.
    2. *1: Refer to Smart Key System (for Start Function) (Click here).


    Power Management Control ECU / Techstream Display "Power Source Control" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0140
    Lost Communication with Main Body ECU
    The power management control ECU (power management CPU) does not receive data from the main body ECU (multiplex network body ECU) for 3.1 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG) for 10 seconds or more.
    2. The power source voltage of the power management control ECU is 10 V or more.
    Turn the ignition switch ON (IG) and wait 20 seconds or more.
    -
    DTC is stored until it is cleared using the Techstream.
    U0155
    Lost Communication with Combination Meter
    The power management control ECU (power management CPU) does not receive data from the combination meter assembly for 3.1 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG) for 10 seconds or more.
    2. The power source voltage of the power management control ECU is 10 V or more.
    Turn the ignition switch ON (IG) and wait 20 seconds or more.
    -
    DTC is stored until it is cleared using the Techstream.
    U0293*1
    Lost Communication with HV ECU
    The power management control ECU (power management CPU) does not receive data from the power management control ECU (HV CPU) for 3.1 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG) for 10 seconds or more.
    2. The power source voltage of the power management control ECU is 9.5 V or more.
    Turn the ignition switch ON (IG) and wait 13.1 seconds or more.
    -
    DTC is stored until it is cleared using the Techstream.

  3. Power Management Control ECU (w/ Cruise Control System) / Techstream Display "Cruise Control"

    HINT:
    This ECU uses the CAN communication system for DTC communication.


    Power Management Control ECU / Techstream Display "Cruise Control" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0122
    Lost Communication with Vehicle Dynamics Control Module
    While the cruise control system is on (the system has been switched on using the ON/OFF button on the cruise control switch), the power management control ECU (HV CPU) does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 2.62 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG) for 2.1 seconds or more.
    2. The power source voltage of the power management control ECU is 9.5 V or more.
    After turning the ignition switch ON (IG), turn the cruise control main switch on and wait for at least 4.72 seconds.
    1. Displays messages on the multi-information display.
    2. Master warning light turns on.
    DTC is stored until it is cleared using the Techstream.

  4. ECM / Techstream Display "Engine and ECT"

    HINT:
    This ECU uses the CAN communication system for DTC communication.


    ECM / Techstream Display "Engine and ECT" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0293
    Lost Communication with HV ECU
    The ECM does not receive data from the power management control ECU (HV CPU) for 0.576 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG) for 1 second or more.
    2. The power source voltage of the ECM is 10.5 V or more.
    Turn the ignition switch ON (IG) and wait 1.576 seconds or more.
    MIL illuminates.
    DTC is stored until it is cleared using the Techstream.

  5. Power Steering ECU Assembly / Techstream Display "EMPS"

    HINT:
    This ECU uses the CAN communication system for DTC communication.


    Power Steering ECU Assembly / Techstream Display "EMPS" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0129
    Lost Communication with Brake System Control Module
    The power steering ECU assembly cannot receive data from the brake booster with master cylinder assembly (skid control ECU) for 2.34 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG) for 2 seconds or more.
    2. The power source voltage of the power steering ECU assembly is 9 V or more.
    Turn the ignition switch ON (IG) and wait 4.3 seconds or more.
    EPS warning light illuminates.
    DTC remains stored only while malfunction is occurring.
    U0293
    Lost Communication with Hybrid Control Module
    The power steering ECU assembly cannot receive data from the power management control ECU (HV CPU) for 5 minutes or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG) for 2 seconds or more.
    2. The power source voltage of the power steering ECU assembly is 9 V or more.
    3. Vehicle speed is 20 km/h (12 mph) or more.
    Drive the vehicle at a speed of 20 km/h (12 mph) or more.
    EPS warning light illuminates.
    DTC remains stored only while malfunction is occurring.

  6. Brake Booster with Master Cylinder Assembly (Skid Control ECU) / Techstream Display "ABS/VSC/TRAC"

    HINT:
    This ECU uses the CAN communication system for DTC communication.


    Brake Booster with Master Cylinder Assembly (Skid Control ECU) / Techstream Display "ABS/VSC/TRAC" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0073
    Control Module Communication Bus OFF
    One of the following conditions is met:
    1. The brake booster with master cylinder assembly (skid control ECU) keeps sending data to an ECU or a sensor for 5 seconds or more because a reception completion cannot be received.
    2. The yaw rate sensor, acceleration sensor or steering sensor and brake booster with master cylinder assembly (skid control ECU) cannot communicate for 1 second or more.
    3. The following condition occurs 10 times in succession within 60 seconds:
      1. The yaw rate sensor, acceleration sensor or steering sensor cannot communicate with the brake booster with master cylinder assembly (skid control ECU) once or more within 5 seconds.
    4. The following condition occurs 10 times in succession:
      1. The brake booster with master cylinder assembly (skid control ECU) cannot send/ receive data (bus off) once or more within 0.1 seconds.
    Both conditions are met:
    1. The ignition switch is turned ON (IG) for 1 second or more.
    2. The power source voltage of the brake booster with master cylinder assembly (skid control ECU) is 10 to 17.4 V or more.
    Turn the ignition switch ON (IG) and wait 60 seconds or more.
    <When data can be sent to the combination meter>
    1. ABS warning light illuminates.
    2. Brake warning light / yellow (minor malfunction) illuminates.
    3. Slip warning light illuminates.
    DTC is stored until it is cleared using the Techstream.
    <When data cannot be sent to the combination meter>
    1. ABS warning light illuminates.
    2. Brake warning light / red (malfunction) illuminates.
    3. Slip warning light illuminates.
    U0123
    Lost Communication with Yaw Rate Sensor Module
    One of the following conditions is met:
    1. The brake booster with master cylinder assembly (skid control ECU) cannot receive data from the yaw rate sensor for 1 second or more.
    2. The following condition occurs 10 times in succession within 60 seconds:
      1. The brake booster with master cylinder assembly (skid control ECU) cannot communicate with the yaw rate sensor once or more within 5 seconds.
    Both conditions are met:
    1. The ignition switch is turned ON (IG) for 1 second or more.
    2. The power source voltage of the brake booster with master cylinder assembly (skid control ECU) is 10 to 17.4 V or more.
    Turn the ignition switch ON (IG) and wait 60 seconds or more.
    1. ABS warning light illuminates.
    2. Brake warning light / yellow (minor malfunction) illuminates.
    3. Slip warning light illuminates.
    DTC is stored until it is cleared using the Techstream.
    U0124
    Lost Communication with Lateral Acceleration Sensor Module
    One of the following conditions is met:
    1. The brake booster with master cylinder assembly (skid control ECU) cannot receive data from the acceleration sensor for 1 second or more.
    2. The following condition occurs 10 times in succession within 60 seconds:
      1. The brake booster with master cylinder assembly (skid control ECU) cannot communicate with the acceleration sensor once or more within 5 seconds.
    Both conditions are met:
    1. The ignition switch is turned ON (IG) for 1 second or more.
    2. The power source voltage of the brake booster with master cylinder assembly (skid control ECU) is 10 to 17.4 V or more.
    Turn the ignition switch ON (IG) and wait 60 seconds or more.
    1. ABS warning light illuminates.
    2. Brake warning light / yellow (minor malfunction) illuminates.
    3. Slip warning light illuminates.
    DTC is stored until it is cleared using the Techstream.
    U0126
    Lost Communication with Steering Angle Sensor Module
    One of the following conditions is met:
    1. The brake booster with master cylinder assembly (skid control ECU) cannot receive data from the spiral cable with sensor sub-assembly (steering sensor) for 1 second or more.
    2. The following condition occurs 10 times in succession within 60 seconds:
      1. The brake booster with master cylinder assembly (skid control ECU) cannot communicate with the steering sensor once or more within 5 seconds.
    Both conditions are met:
    1. The ignition switch is turned ON (IG) for 1 second or more.
    2. The power source voltage of the brake booster with master cylinder assembly (skid control ECU) is 10 to 17.4 V or more.
    Turn the ignition switch ON (IG) and wait 60 seconds or more.
    Slip warning light illuminates.
    DTC is stored until it is cleared using the Techstream.
    U0293
    Communication Error from HV ECU
    One of the following conditions is met:
    1. With the IG2 terminal voltage of the brake booster with master cylinder assembly (skid control ECU) 9.5 V or more, the brake booster with master cylinder assembly (skid control ECU) does not receive data from the power management control ECU (HV CPU) for 2 seconds or more.
    2. The following condition occurs 10 times in succession within 60 seconds:
      1. With the IG2 terminal voltage of the brake booster with master cylinder assembly (skid control ECU) 9.5 V or more, the brake booster with master cylinder assembly (skid control ECU) does not receive data from the power management control ECU (HV CPU) once or more within 5 seconds.
    Both conditions are met:
    1. The ignition switch is turned ON (IG) for 1 second or more.
    2. The power source voltage of the brake booster with master cylinder assembly (skid control ECU) is 10 to 17.4 V or more.
    Turn the ignition switch ON (IG) and wait 60 seconds or more.
    1. Brake warning light / yellow (minor malfunction) illuminates.
    2. Slip warning light illuminates.
    DTC is stored until it is cleared using the Techstream.

  7. Spiral Cable with Sensor Sub-assembly (Steering sensor) / Techstream Display "Spiral cable (Steering Angle Sensor)"

    HINT:
    The steering sensor is connected to the CAN communication system, but the steering sensor does not store or output CAN communication DTCs.

  8. Airbag Sensor Assembly / Techstream Display "Airbag"

    HINT:
    The airbag sensor assembly is connected to the CAN communication system, but the airbag sensor assembly does not store or output CAN communication DTCs.

  9. Multiplex Network Body ECU / Techstream Display "Main Body"

    HINT:
    1. This ECU uses the CAN communication system for DTC communication.
    2. *1: w/ Smart key system.


    Multiplex Network Body ECU / Techstream Display "Main Body" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0100
    Lost Communication with ECM / PCM "A"
    The main body ECU (multiplex network body ECU) does not receive data from the ECM for 10 seconds or more.
    Both conditions are met:
    1. Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse.
    2. The power source voltage of the main body ECU (main body ECU (multiplex network body ECU)) is 10 V or more.
    Turn the ignition switch ON (IG) and wait at least 20 seconds.
    -
    DTC is stored until it is cleared using the Techstream.
    U0101
    Lost Communication with ECT
    The main body ECU (multiplex network body ECU) does not receive data from the power management control ECU (HV CPU) for 10 seconds or more.
    Both conditions are met:
    1. Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse.
    2. The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more.
    Turn the ignition switch ON (IG) and wait at least 20 seconds.
    -
    DTC is stored until it is cleared using the Techstream.
    U0120*1
    Lost Communication With Starter / Generator Control Module
    The main body ECU (multiplex network body ECU) does not receive data from the power management control ECU (power management CPU) for 10 seconds or more.
    Both conditions are met:
    1. Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse.
    2. The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more.
    Turn the ignition switch ON (IG) and wait at least 20 seconds.
    -
    DTC is stored until it is cleared using the Techstream.
    U0151
    Communication Error from Airbag ECU to HV ECU
    The main body ECU (multiplex network body ECU) does not receive data from the airbag sensor assembly for 10 seconds or more.
    Both conditions are met:
    1. Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse.
    2. The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more.
    Turn the ignition switch ON (IG) and wait at least 20 seconds.
    -
    DTC is stored until it is cleared using the Techstream.
    U0155
    Lost Communication with Combination Meter
    The main body ECU (multiplex network body ECU) does not receive data from the combination meter assembly for 10 seconds or more.
    Both conditions are met:
    1. Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse.
    2. The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more.
    Turn the ignition switch ON (IG) and wait at least 20 seconds.
    -
    DTC is stored until it is cleared using the Techstream.
    U0164
    Communication Error from A/C ECU to HV ECU
    The main body ECU (multiplex network body ECU) does not receive data from the air conditioning amplifier assembly for 10 seconds or more.
    Both conditions are met:
    1. Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse.
    2. The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more.
    Turn the ignition switch ON (IG) and wait at least 20 seconds.
    -
    DTC is stored until it is cleared using the Techstream.
    U0293
    Communication Error from HV ECU
    The main body ECU (multiplex network body ECU) does not receive data from the power management control ECU (HV CPU) for 10 seconds or more.
    Both conditions are met:
    1. Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse.
    2. The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more.
    Turn the ignition switch ON (IG) and wait at least 20 seconds.
    -
    DTC is stored until it is cleared using the Techstream.
    U0327*1
    Software Incompatibility with Vehicle Security Control Module
    The main body ECU (multiplex network body ECU) does not receive data from the smart key ECU assembly (certification ECU) for 10 seconds or more.
    Both conditions are met:
    1. Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse.
    2. The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more.
    Turn the ignition switch ON (IG) and wait at least 20 seconds.
    -
    DTC is stored until it is cleared using the Techstream.

  10. Smart Key ECU Assembly (Certification ECU) (w/ Smart Key System) / Techstream Display "Smart Key"

    HINT:
    This ECU uses the CAN communication system for DTC communication.


    Smart Key ECU Assembly (Certification ECU) / Techstream Display "Smart Key" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0100
    Lost Communication with ECM
    The smart key ECU assembly (certification ECU) does not receive data from the ECM for 10 seconds or more.
    Both conditions are met:
    1. Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse.
    2. The power source voltage of the smart key ECU assembly (certification ECU) is 10 V or more.
    Turn the ignition switch ON (IG) and wait at least 20 seconds.
    -
    DTC is stored until it is cleared using the Techstream.
    U0142
    Lost Communication with Main Body ECU
    The smart key ECU assembly (certification ECU) does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG) for 10 second or more.
    2. The power source voltage of the smart key ECU assembly (certification ECU) is 10 V or more.
    Turn the ignition switch ON (IG) and wait at least 11 seconds.
    -
    DTC is stored until it is cleared using the Techstream.
    U0155
    Lost Communication with Combination Meter
    The smart key ECU assembly (certification ECU) does not receive data from the combination meter assembly for 10 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG) for 10 second or more.
    2. The power source voltage of the smart key ECU assembly (certification ECU) is 10 V or more.
    Turn the ignition switch ON (IG) and wait at least 11 seconds.
    -
    DTC is stored until it is cleared using the Techstream.
    U0293
    Lost Communication with HV ECU
    The smart key ECU assembly (certification ECU) does not receive data from the power management control ECU (HV CPU) for 10 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG) for 10 second or more.
    2. The power source voltage of the smart key ECU assembly (certification ECU) is 10 V or more.
    Turn the ignition switch ON (IG) and wait at least 11 seconds.
    -
    DTC is stored until it is cleared using the Techstream.

  11. Air Conditioning Amplifier Assembly / Techstream Display "Air Conditioner"

    HINT:
    This ECU uses the CAN communication system for DTC communication.


    Air Conditioning Amplifier Assembly / Techstream Display "Air Conditioner" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0101
    Lost Communication With TCM
    The air conditioning amplifier assembly does not receive data from the power management control ECU (HV CPU) for 5 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG).
    2. The power source voltage of the air conditioning amplifier assembly is 10 V or more.
    Turn the ignition switch ON (IG) and wait at least 5 seconds.
    -
    DTC is stored until it is cleared using the Techstream.
    U0142
    Lost Communication with Main Body ECU
    The air conditioning amplifier assembly does not receive data from the main body ECU (multiplex network body ECU) for 5 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG).
    2. The power source voltage of the air conditioning amplifier assembly is 10 V or more.
    Turn the ignition switch ON (IG) and wait at least 5 seconds.
    -
    DTC is stored until it is cleared using the Techstream.
    U0155
    Lost Communication with Combination Meter
    The air conditioning amplifier assembly does not receive data from the combination meter assembly for 5 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG).
    2. The power source voltage of the air conditioning amplifier assembly is 10 V or more.
    Turn the ignition switch ON (IG) and wait at least 5 seconds.
    -
    DTC is stored until it is cleared using the Techstream.
    U0293
    Lost Communication with HV ECU
    The air conditioning amplifier assembly does not receive data from the power management control ECU (HV CPU) for 5 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG).
    2. The power source voltage of the air conditioning amplifier assembly is 10 V or more.
    Turn the ignition switch ON (IG) and wait at least 5 seconds.
    -
    DTC is stored until it is cleared using the Techstream.

  12. Combination Meter Assembly / Techstream Display "Combination Meter"

    HINT:
    This ECU uses the CAN communication system for DTC communication.


    Combination Meter Assembly / Techstream Display "Combination Meter" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0100
    Lost Communication with ECM / PCM "A"
    The combination meter assembly does not receive data from the ECM for 2 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG).
    2. The power source voltage of the combination meter assembly is 9.5 V or more.
    Turn the ignition switch ON (IG) and wait at least 2 seconds.
    -
    DTC is stored until it is cleared using the Techstream.
    U0129
    Lost Communication with Skid Control ECU
    The combination meter assembly does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 2 seconds or 3 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG).
    2. The power source voltage of the combination meter assembly is 9.5 V or more.
    Turn the ignition switch ON (IG) and wait at least 3 seconds.
    -
    DTC is stored until it is cleared using the Techstream.
    U0131
    Lost Communication with Power Steering Control Module
    The combination meter assembly does not receive data from the power steering ECU assembly for 3 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG).
    2. The power source voltage of the combination meter assembly is 9.5 V or more.
    Turn the ignition switch ON (IG) and wait at least 3 seconds.
    EPS warning light illuminates.
    DTC is stored until it is cleared using the Techstream.
    U0142
    Lost Communication with Main Body ECU
    The combination meter assembly does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG).
    2. The power source voltage of the combination meter assembly is 9.5 V or more.
    Turn the ignition switch ON (IG) and wait at least 3 seconds.
    Tire pressure warning light illuminates.
    DTC is stored until it is cleared using the Techstream.
    U0151
    Lost Communication with Airbag ECU
    The combination meter assembly does not receive data from the airbag sensor assembly for 10 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG).
    2. The power source voltage of the combination meter assembly is 9.5 V or more.
    Turn the ignition switch ON (IG) and wait at least 10 seconds.
    SRS warning light illuminates.
    DTC is stored until it is cleared using the Techstream.

  13. Radio and Display Receiver Assembly (for Radio and Display Type) / Techstream Display "Navigation System"

    HINT:
    This ECU uses the CAN communication system for DTC communication.


    Radio and Display Receiver Assembly (for Radio and Display Type) / Techstream Display "Navigation System" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0073
    Sending Malfunction (Navigation to APGS)
    The radio and display receiver assembly does not send/receive data for 10 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned to ACC for 1 second or more.
    2. The power source voltage of the radio and display receiver assembly is 9.5 V or more.
    Turn the ignition switch to ACC and wait at least 11.08 seconds.
    -
    DTC is stored until it is cleared using the Techstream.
    U0100
    Lost Communication with ECM / PCM "A"
    The radio and display receiver assembly does not receive data from the power management control ECU for 12 seconds or more.
    All conditions are met:
    1. The ignition switch is turned ON (IG) for 1 second or more.
    2. The power source voltage of the radio and display receiver assembly is 9.5 V or more.
    Turn the ignition switch ON (IG) and wait at least 13 seconds.
    -
    DTC is stored until it is cleared using the Techstream.
    U0129
    Lost Communication with Brake System Control Module
    The radio and display receiver assembly does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 1 second or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG) for 1 second or more.
    2. The power source voltage of the radio and display receiver assembly is 9.5 V or more.
    Turn the ignition switch ON (IG) and wait at least 2 seconds.
    -
    DTC is stored until it is cleared using the Techstream.
    U0140
    Lost Communication with Body Control Module
    The radio and display receiver assembly does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG) for 1 second or more.
    2. The power source voltage of the radio and display receiver assembly is 9.5 V or more.
    Turn the ignition switch ON (IG) and wait at least 11 seconds.
    -
    DTC is stored until it is cleared using the Techstream.
    U0155
    Meter ECU Communication
    The radio and display receiver assembly does not receive data from the combination meter assembly for 30 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG) for 1 second or more.
    2. The power source voltage of the radio and display receiver assembly is 9.5 V or more.
    Turn the ignition switch ON (IG) and wait at least 31 seconds.
    -
    DTC is stored until it is cleared using the Techstream.
    U0293
    Lost Communication with HV ECU
    The radio and display receiver assembly does not receive data from the power management control ECU (HV CPU) for 4 seconds or more.
    Both conditions are met:
    1. The ignition switch is turned ON (IG) for 1 second or more.
    2. The power source voltage of the radio and display receiver assembly is 9.5 V or more.
    Turn the ignition switch ON (IG) and wait at least 5 seconds.
    -
    DTC is stored until it is cleared using the Techstream.


DTC COMBINATION TABLE (OPEN IN CAN BRANCH OF V BUS, PAST COMMUNICATION ERROR)
  1. Regarding the past communication error of ECUs and sensors connected to the V bus (in this case, normal was displayed when performing the CAN bus check, but communication DTCs are output), the probable CAN branch that had a malfunction can be determined based on the following DTC combination table.

    HINT:
    1. Based on the table below and DTCs output from ECUs connected via CAN communication, the probable part for which communication stop occurred can be determined.
    2. Regarding an open in a CAN branch and a communication stop that is currently occurring, the malfunctioning part can be confirmed easily by performing the CAN bus check using the Techstream because the ECU or sensor connected to the CAN branch does not respond (the ECU or sensor name will not be displayed on the screen).
    3. If an open in a CAN main bus line, a short between the CAN bus lines (CANH and CANL) or a +B or ground short in the CAN bus occurs, DTCs of almost all ECUs (or sensors) on the CAN bus may be output, or a message indicating a communication error may be displayed on the Techstream screen. In this case, check the resistance of the CAN bus (steps 7 to 9) first (Click here).
    4. If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed.



    V Bus (Open in one CAN branch line)
    Trouble Mode
    Output ECU
    Output DTC
    Center Airbag Sensor Communication Stop Mode (Click here)
    Air Conditioning Amplifier Communication Stop Mode (Click here)
    Audio Receiver Assembly Communication Stop Mode (Click here)
    Main Body ECU Communication Stop Mode (Click here)
    Skid Control ECU Communication Stop Mode (Click here)
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0101
    -
    ○
    -
    -
    -
    U0142
    -
    ○
    -
    ○
    -
    U0155
    -
    ○
    -
    -
    -
    U0293
    -
    ○
    -
    -
    -
    Radio and Display Receiver Assembly*5
    U0073
    X
    X
    ○
    X
    X
    U0100
    -
    -
    ○
    -
    -
    U0129
    X
    X
    ○
    X
    ○
    U0140
    -
    -
    ○
    ○
    -
    U0155
    -
    -
    ○
    -
    -
    U0293
    -
    -
    ○
    -
    -
    Multiplex Network Body ECU
    U0100
    -
    -
    -
    ○
    -
    U0101
    -
    -
    -
    ○
    -
    U0120*2
    X
    X
    X
    ○
    X
    U0151
    ○
    -
    -
    ○
    -
    U0155
    -
    -
    -
    ○
    -
    U0164
    -
    ○
    -
    ○
    -
    U0293
    -
    -
    -
    ○
    -
    U0327*2
    -
    -
    -
    ○
    -
    V Bus
    Brake Booster with Master Cylinder Assembly (Skid Control ECU)
    U0073
    X
    X
    X
    X
    ○*1
    U0123
    ○
    X
    X
    X
    ○
    U0124
    ○
    X
    X
    X
    ○
    U0126
    X
    X
    X
    X
    ○
    U0293
    -
    -
    -
    -
    ○
    Power Management Control ECU (HV CPU)
    U0100
    -
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    ○
    U0140*3
    -
    -
    -
    ○
    -
    U0151
    ○
    -
    -
    -
    -
    U0164
    -
    ○
    -
    -
    -
    U1107*2
    X
    X
    X
    X
    X
    Power Management Control ECU
    (Cruise Control)*4
    U0122
    X
    X
    X
    X
    ○
    Power Management Control ECU
    (Power Management CPU)
    U0140
    X
    X
    X
    X
    X
    U0155
    X
    X
    X
    X
    X
    U0293
    X
    X
    X
    X
    X
    Power Steering ECU Assembly
    U0129
    -
    -
    -
    -
    ○
    U0293
    X
    X
    X
    X
    X
    ECM
    U0293
    -
    -
    -
    -
    -
    Smart Key ECU Assembly (Certification ECU)*2
    U0100
    -
    -
    -
    -
    -
    U0142
    -
    -
    -
    ○
    -
    U0155
    -
    -
    -
    -
    -
    U0293
    X
    X
    X
    X
    X
    Combination Meter Assembly
    U0100
    -
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    ○
    U0131
    -
    -
    -
    -
    -
    U0142
    X
    X
    X
    ○
    X
    U0151
    ○
    -
    -
    -
    -
    Spiral Cable with Sensor Sub-assembly (Steering Sensor)
    -
    -
    -
    -
    -
    -
    DLC3
    -
    -
    -
    -
    -
    -
    Sub Bus 15
    ECM
    U0293
    -
    -
    -
    -
    -
    Brake Booster with Master Cylinder Assembly (Skid Control ECU)
    U0073
    -
    -
    -
    -
    -
    U0123
    -
    -
    -
    -
    -
    U0124
    -
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    -
    U0293
    -
    -
    -
    -
    -
    Power Management Control ECU (HV CPU)
    U0100
    -
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    -
    U0140*3
    -
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    -
    U0164
    -
    -
    -
    -
    -
    U1107*2
    -
    -
    -
    -
    -
    Power Management Control ECU
    (Cruise Control)*4
    U0122
    -
    -
    -
    -
    -


    V Bus (Open in one CAN branch line)
    Trouble Mode
    Output ECU
    Output DTC
    Power Management Control ECU Communication Stop Mode (Click here)
    Power Steering ECU Communication Stop Mode (Click here)
    Certification ECU Communication Stop Mode (Click here)
    Steering Angle Sensor Communication Stop Mode (Click here)
    DLC3
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0101
    ○
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    -
    U0293
    -
    -
    -
    -
    -
    Radio and Display Receiver Assembly*5
    U0073
    X
    X
    X
    X
    X
    U0100
    ○
    -
    -
    -
    -
    U0129
    X
    X
    X
    X
    X
    U0140
    -
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    -
    U0293
    ○
    -
    -
    -
    -
    Multiplex Network Body ECU
    U0100
    -
    -
    -
    -
    -
    U0101
    ○
    -
    -
    -
    -
    U0120*2
    ○
    X
    X
    X
    X
    U0151
    -
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    -
    U0164
    -
    -
    -
    -
    -
    U0293
    ○
    -
    -
    -
    -
    U0327*2
    -
    -
    ○
    -
    -
    V Bus
    Brake Booster with Master Cylinder Assembly (Skid Control ECU)
    U0073
    X
    X
    X
    X
    X
    U0123
    X
    X
    X
    X
    X
    U0124
    X
    X
    X
    X
    X
    U0126
    X
    X
    X
    ○
    X
    U0293
    ○
    -
    -
    -
    -
    Power Management Control ECU (HV CPU)
    U0100
    -
    -
    -
    -
    -
    U0129
    ○
    -
    -
    -
    -
    U0140*3
    ○
    -
    -
    -
    -
    U0151
    ○
    -
    -
    -
    -
    U0164
    ○
    -
    -
    -
    -
    U1107*2
    ○
    X
    X
    X
    X
    Power Management Control ECU
    (Cruise Control)*4
    U0122
    ○
    X
    X
    X
    X
    Power Management Control ECU
    (Power Management CPU)
    U0140
    ○
    X
    X
    X
    X
    U0155
    ○
    X
    X
    X
    X
    U0293
    ○
    X
    X
    X
    X
    Power Steering ECU Assembly
    U0129
    X
    ○
    -
    -
    -
    U0293
    ○
    ○
    X
    X
    X
    ECM
    U0293
    -
    -
    -
    -
    -
    Smart Key ECU Assembly (Certification ECU)*2
    U0100
    -
    -
    ○
    -
    -
    U0142
    -
    -
    ○
    -
    -
    U0155
    -
    -
    ○
    -
    -
    U0293
    ○
    X
    ○
    X
    X
    Combination Meter Assembly
    U0100
    ○
    -
    -
    -
    -
    U0129
    X
    -
    -
    -
    -
    U0131
    -
    ○
    -
    -
    -
    U0142
    X
    X
    X
    X
    X
    U0151
    -
    -
    -
    -
    -
    Spiral Cable with Sensor Sub-assembly (Steering Sensor)
    -
    -
    -
    -
    -
    -
    DLC3
    -
    -
    -
    -
    -
    -
    Sub Bus 15
    ECM
    U0293
    -
    -
    -
    -
    -
    Brake Booster with Master Cylinder Assembly (Skid Control ECU)
    U0073
    -
    -
    -
    -
    -
    U0123
    -
    -
    -
    -
    -
    U0124
    -
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    -
    U0293
    -
    -
    -
    -
    -
    Power Management Control ECU (HV CPU)
    U0100
    -
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    -
    U0140*3
    -
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    -
    U0164
    -
    -
    -
    -
    -
    U1107*2
    -
    -
    -
    -
    -
    Power Management Control ECU
    (Cruise Control)*4
    U0122
    -
    -
    -
    -
    -

    HINT:
    1. ○: Set
    2. X: Not set or may be set according to the malfunctioning part when one line of a CAN branch is open.
    3. -: DTC is not output.
    4. *1: DTC U0123, U0124, U0126 and U0293 are not stored when DTC U0073 has already been stored.
    5. *2: w/ Smart key system
    6. *3: w/o Smart key system
    7. *4: w/ Cruise control system
    8. *5: for Radio and display receiver type
    9. If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed.



    V Bus (Open in both CAN branch lines)
    Trouble Mode
    Output ECU
    Output DTC
    Center Airbag Sensor Communication Stop Mode (Click here)
    Air Conditioning Amplifier Communication Stop Mode (Click here)
    Audio Receiver Assembly Communication Stop Mode (Click here)
    Main Body ECU Communication Stop Mode (Click here)
    Skid Control ECU Communication Stop Mode (Click here)
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    -
    -
    V Bus
    Air Conditioning Amplifier Assembly
    U0101
    -
    ○
    -
    -
    -
    U0142
    -
    ○
    -
    ○
    -
    U0155
    -
    ○
    -
    -
    -
    U0293
    -
    ○
    -
    -
    -
    Radio and Display Receiver Assembly*5
    U0073
    -
    -
    ○
    -
    -
    U0100
    -
    -
    ○
    -
    -
    U0129
    -
    -
    ○
    -
    ○
    U0140
    -
    -
    ○
    ○
    -
    U0155
    -
    -
    ○
    -
    -
    U0293
    -
    -
    ○
    -
    -
    Multiplex Network Body ECU
    U0100
    -
    -
    -
    ○
    -
    U0101
    -
    -
    -
    ○
    -
    U0120*2
    -
    -
    -
    ○
    -
    U0151
    ○
    -
    -
    ○
    -
    U0155
    -
    -
    -
    ○
    -
    U0164
    -
    ○
    -
    ○
    -
    U0293
    -
    -
    -
    ○
    -
    U0327*2
    -
    -
    -
    ○
    -
    Brake Booster with Master Cylinder Assembly (Skid Control ECU)
    U0073
    -
    -
    -
    -
    ○*1
    U0123
    ○
    -
    -
    -
    ○
    U0124
    ○
    -
    -
    -
    ○
    U0126
    -
    -
    -
    -
    ○
    U0293
    -
    -
    -
    -
    ○
    Power Management Control ECU (HV CPU)
    U0100
    -
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    ○
    U0140*3
    -
    -
    -
    ○
    -
    U0151
    ○
    -
    -
    -
    -
    U0164
    -
    ○
    -
    -
    -
    U1107*2
    -
    -
    -
    -
    -
    Power Management Control ECU
    (Cruise Control)*4
    U0122
    -
    -
    -
    -
    ○
    Power Management Control ECU
    (Power Management CPU)
    U0140
    -
    -
    -
    ○
    -
    U0155
    -
    -
    -
    -
    -
    U0293
    -
    -
    -
    -
    -
    Power Steering ECU Assembly
    U0129
    -
    -
    -
    -
    ○
    U0293
    -
    -
    -
    -
    -
    ECM
    U0293
    -
    -
    -
    -
    -
    V Bus
    Smart Key ECU Assembly (Certification ECU)*2
    U0100
    -
    -
    -
    -
    -
    U0142
    -
    -
    -
    ○
    -
    U0155
    -
    -
    -
    -
    -
    U0293
    -
    -
    -
    -
    -
    Combination Meter Assembly
    U0100
    -
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    ○
    U0131
    -
    -
    -
    -
    -
    U0142
    -
    -
    -
    ○
    -
    U0151
    ○
    -
    -
    -
    -
    Spiral Cable with Sensor Sub-assembly (Steering Sensor)
    -
    -
    -
    -
    -
    -
    DLC3
    -
    -
    -
    -
    -
    -
    Sub Bus 15
    ECM
    U0293
    -
    -
    -
    -
    -
    Brake Booster with Master Cylinder Assembly (Skid Control ECU)
    U0073
    -
    -
    -
    -
    -
    U0123
    -
    -
    -
    -
    -
    U0124
    -
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    -
    U0293
    -
    -
    -
    -
    -
    Power Management Control ECU (HV CPU)
    U0100
    -
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    -
    U0140*3
    -
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    -
    U0164
    -
    -
    -
    -
    -
    U1107*2
    -
    -
    -
    -
    -
    Power Management Control ECU
    (Cruise Control)*4
    U0122
    -
    -
    -
    -
    -


    V Bus (Open in both CAN branch lines)
    Trouble Mode
    Output ECU
    Output DTC
    Power Management Control ECU Communication Stop Mode (Click here)
    Power Steering ECU Communication Stop Mode (Click here)
    Certification ECU Communication Stop Mode (Click here)
    Steering Angle Sensor Communication Stop Mode (Click here)
    DLC3
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0101
    ○
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    -
    U0293
    -
    -
    -
    -
    -
    V Bus
    Radio and Display Receiver Assembly*5
    U0073
    -
    -
    -
    -
    -
    U0100
    ○
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    -
    U0140
    -
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    -
    U0293
    ○
    -
    -
    -
    -
    Multiplex Network Body ECU
    U0100
    -
    -
    -
    -
    -
    U0101
    ○
    -
    -
    -
    -
    U0120*2
    ○
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    -
    U0164
    -
    -
    -
    -
    -
    U0293
    ○
    -
    -
    -
    -
    U0327*2
    -
    -
    ○
    -
    -
    Brake Booster with Master Cylinder Assembly (Skid Control ECU)
    U0073
    -
    -
    -
    -
    -
    U0123
    -
    -
    -
    -
    -
    U0124
    -
    -
    -
    -
    -
    U0126
    -
    -
    -
    ○
    -
    U0293
    ○
    -
    -
    -
    -
    Power Management Control ECU (HV CPU)
    U0100
    -
    -
    -
    -
    -
    U0129
    ○
    -
    -
    -
    -
    U0140*3
    ○
    -
    -
    -
    -
    U0151
    ○
    -
    -
    -
    -
    U0164
    ○
    -
    -
    -
    -
    U1107*2
    ○
    -
    -
    -
    -
    Power Management Control ECU (Cruise Control)*4
    U0122
    ○
    -
    -
    -
    -
    Power Management Control ECU
    (Power Management CPU)
    U0140
    ○
    -
    -
    -
    -
    U0155
    ○
    -
    -
    -
    -
    U0293
    ○
    -
    -
    -
    -
    Power Steering ECU Assembly
    U0129
    -
    ○
    -
    -
    -
    U0293
    ○
    ○
    -
    -
    -
    ECM
    U0293
    -
    -
    -
    -
    -
    Smart Key ECU Assembly (Certification ECU)*2
    U0100
    -
    -
    ○
    -
    -
    U0142
    -
    -
    ○
    -
    -
    U0155
    -
    -
    ○
    -
    -
    U0293
    ○
    -
    ○
    -
    -
    V Bus
    Combination Meter Assembly
    U0100
    ○
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    -
    U0131
    -
    ○
    -
    -
    -
    U0142
    -
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    -
    Spiral Cable with Sensor Sub-assembly (Steering Sensor)
    -
    -
    -
    -
    -
    -
    DLC3
    -
    -
    -
    -
    -
    -
    Sub Bus 15
    ECM
    U0293
    -
    -
    -
    -
    -
    Brake Booster with Master Cylinder Assembly (Skid Control ECU)
    U0073
    -
    -
    -
    -
    -
    U0123
    -
    -
    -
    -
    -
    U0124
    -
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    -
    U0293
    -
    -
    -
    -
    -
    Power Management Control ECU (HV CPU)
    U0100
    -
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    -
    U0140*3
    -
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    -
    U0164
    -
    -
    -
    -
    -
    U1107*2
    -
    -
    -
    -
    -
    Power Management Control ECU
    (Cruise Control)*4
    U0122
    -
    -
    -
    -
    -

    HINT:
    1. ○: Set
    2. -: DTC is not output.
    3. *1: DTC U0123, U0124, U0126 and U0293 are not stored when DTC U0073 has already been stored.
    4. *2: w/ Smart key system
    5. *3: w/o Smart key system
    6. *4: w/ Cruise control system
    7. *5: for Radio and display receiver type



    V Bus (Open in one CAN main bus line)
    V Bus (Open in both CAN main bus lines)
    Trouble Mode
    Trouble Mode
    Output ECU
    Output DTC
    ECM Communication Stop Mode (Click here)
    CAN J/C LH to CAN J/C RH
    Combination Meter ECU Communication Stop Mode (Click here)
    ECM Communication Stop Mode (Click here)
    CAN J/C LH to CAN J/C RH
    Combination Meter ECU Communication Stop Mode (Click here)
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0101
    -
    ○
    -
    -
    ○
    -
    U0142
    -
    ○
    -
    -
    ○
    -
    U0155
    -
    -
    ○
    -
    -
    ○
    U0293
    ○
    ○
    -
    ○
    ○
    -
    Radio and Display Receiver Assembly*4
    U0073
    X
    X
    X
    X
    X
    X
    U0100
    ○
    ○
    -
    ○
    ○
    -
    U0129
    X
    ○
    X
    -
    ○
    -
    U0140
    -
    ○
    -
    -
    ○
    -
    U0155
    -
    -
    ○
    -
    -
    ○
    U0293
    -
    ○
    -
    -
    ○
    -
    Multiplex Network Body ECU
    U0100
    ○
    X
    -
    ○
    -
    -
    U0101
    -
    X
    -
    -
    -
    -
    U0120*1
    X
    X
    X
    X
    X
    X
    U0151
    -
    ○
    -
    -
    ○
    -
    U0155
    -
    ○
    ○
    -
    ○
    ○
    U0164
    -
    ○
    -
    -
    ○
    -
    U0293
    -
    X
    -
    -
    -
    -
    U0327*1
    -
    ○
    -
    -
    ○
    -
    Brake Booster with Master Cylinder Assembly (Skid Control ECU)
    U0073
    X
    X
    X
    X
    X
    X
    U0123
    X
    ○
    X
    -
    ○
    -
    U0124
    X
    ○
    X
    -
    ○
    -
    U0126
    X
    ○
    X
    -
    ○
    -
    U0293
    -
    X
    -
    -
    -
    -
    Power Management Control ECU (HV CPU)
    U0100
    -
    -
    -
    -
    -
    -
    U0129
    -
    X
    -
    -
    -
    -
    U0140*2
    -
    X
    -
    -
    -
    -
    U0151
    -
    ○
    -
    -
    ○
    -
    U0164
    -
    ○
    -
    -
    ○
    -
    U1107*1
    X
    X
    X
    X
    X
    X
    Power Management Control ECU
    (Cruise Control)*3
    U0122
    X
    X
    X
    X
    X
    X
    Power Management Control ECU
    (Power Management CPU)
    U0140
    X
    X
    X
    X
    X
    X
    U0155
    X
    X
    X
    X
    X
    X
    U0293
    X
    X
    X
    X
    X
    X
    V Bus
    Power Steering ECU Assembly
    U0129
    -
    X
    -
    -
    -
    -
    U0293
    X
    X
    X
    -
    -
    -
    ECM
    U0293
    -
    -
    -
    -
    -
    -
    Smart Key ECU Assembly (Certification ECU)*1
    U0100
    ○
    ○
    -
    ○
    ○
    -
    U0142
    -
    ○
    -
    -
    ○
    -
    U0155
    -
    -
    ○
    -
    -
    ○
    U0293
    X
    X
    X
    X
    X
    X
    Combination Meter Assembly
    U0100
    -
    ○
    ○
    ○
    ○
    ○
    U0129
    -
    ○
    ○
    -
    ○
    ○
    U0131
    -
    ○
    ○
    -
    ○
    ○
    U0142
    X
    ○
    ○
    -
    ○
    ○
    U0151
    -
    -
    ○
    -
    -
    ○
    Spiral Cable with Sensor Sub-assembly (Steering Sensor)
    -
    -
    -
    -
    -
    -
    -
    DLC3
    -
    -
    -
    -
    -
    -
    -
    Sub Bus 15
    ECM
    U0293
    -
    -
    -
    -
    -
    -
    Brake Booster with Master Cylinder Assembly (Skid Control ECU)
    U0073
    -
    -
    -
    -
    -
    -
    U0123
    -
    -
    -
    -
    -
    -
    U0124
    -
    -
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    -
    -
    U0293
    -
    -
    -
    -
    -
    -
    Power Management Control ECU (HV CPU)
    U0100
    -
    -
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    -
    -
    U0140*2
    -
    -
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    -
    -
    U0164
    -
    -
    -
    -
    -
    -
    U1107*1
    -
    -
    -
    -
    -
    -
    Power Management Control ECU
    (Cruise Control)*3
    U0122
    -
    -
    -
    -
    -
    -

    HINT:
    1. ○: Set
    2. X: Not set or may be set according to the malfunctioning part when one line of a CAN branch is open.
    3. -: DTC is not output.
    4. *1: w/ Smart key system
    5. *2: w/o Smart key system
    6. *3: w/ Cruise control system
    7. *4: for Radio and display receiver type
    8. If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed.



    V Bus (CAN bus line short circuit)
    V Bus (CAN bus line short to GND)
    Trouble Mode
    Trouble Mode
    Output ECU
    Output DTC
    CANH to CANL
    CANH to GND
    CANL to GND
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0101
    ○
    ○
    ○
    U0142
    ○
    ○
    ○
    U0155
    ○
    ○
    ○
    U0293
    ○
    ○
    ○
    Radio and Display Receiver Assembly*4
    U0073
    ○
    ○
    ○
    U0100
    ○
    ○
    ○
    U0129
    ○
    ○
    ○
    U0140
    ○
    ○
    ○
    U0155
    ○
    ○
    ○
    U0293
    ○
    ○
    ○
    Multiplex Network Body ECU
    U0100
    ○
    ○
    ○
    U0101
    ○
    ○
    ○
    U0120*1
    ○
    ○
    ○
    U0151
    ○
    ○
    ○
    U0155
    ○
    ○
    ○
    U0164
    ○
    ○
    ○
    U0293
    ○
    ○
    ○
    U0327*1
    ○
    ○
    ○
    Brake Booster with Master Cylinder Assembly (Skid Control ECU)
    U0073
    ○
    ○
    ○
    U0123
    ○
    ○
    ○
    U0124
    ○
    ○
    ○
    U0126
    ○
    ○
    ○
    U0293
    ○
    ○
    ○
    Power Management Control ECU (HV CPU)
    U0100
    -
    -
    -
    U0129
    ○
    ○
    ○
    U0140*2
    ○
    ○
    ○
    U0151
    ○
    ○
    ○
    U0164
    ○
    ○
    ○
    U1107*1
    ○
    ○
    ○
    Power Management Control ECU
    (Cruise Control)*3
    U0122
    ○
    ○
    ○
    V Bus
    Power Management Control ECU
    (Power Management CPU)
    U0140
    ○
    ○
    ○
    U0155
    ○
    ○
    ○
    U0293
    ○
    ○
    ○
    Power Steering ECU Assembly
    U0129
    ○
    ○
    ○
    U0293
    ○
    ○
    ○
    ECM
    U0293
    -
    -
    -
    Smart Key ECU Assembly (Certification ECU)*1
    U0100
    ○
    ○
    ○
    U0142
    ○
    ○
    ○
    U0155
    ○
    ○
    ○
    U0293
    ○
    ○
    ○
    Combination Meter Assembly
    U0100
    ○
    ○
    ○
    U0129
    ○
    ○
    ○
    U0131
    ○
    ○
    ○
    U0142
    ○
    ○
    ○
    U0151
    ○
    ○
    ○
    Spiral Cable with Sensor Sub-assembly (Steering Sensor)
    -
    -
    -
    -
    DLC3
    -
    -
    -
    -
    Sub Bus 15
    ECM
    U0293
    -
    -
    -
    Brake Booster with Master Cylinder Assembly (Skid Control ECU)
    U0073
    -
    -
    -
    U0123
    -
    -
    -
    U0124
    -
    -
    -
    U0126
    -
    -
    -
    U0293
    -
    -
    -
    Power Management Control ECU (HV CPU)
    U0100
    -
    -
    -
    U0129
    -
    -
    -
    U0140*2
    -
    -
    -
    U0151
    -
    -
    -
    U0164
    -
    -
    -
    U1107*1
    -
    -
    -
    Power Management Control ECU
    (Cruise Control)*3
    U0122
    -
    -
    -

    HINT:
    1. ○: Set
    2. -: DTC is not output.
    3. *1: w/ Smart key system
    4. *2: w/o Smart key system
    5. *3: w/ Cruise control system
    6. *4: for Radio and display receiver type
    7. If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed.


DTC COMBINATION TABLE (OPEN IN CAN BRANCH OF SUB BUS 15, PAST COMMUNICATION ERROR)
  1. Regarding the past communication error of ECUs connected to the sub bus 15 (in this case, normal was displayed when performing the communication bus check, but communication DTCs are output), the probable area that had a malfunction can be determined based on the following DTC combination table.

    HINT:
    1. Based on the table below and DTCs output from ECUs connected via CAN communication, the probable part for which communication stop occurred can be determined.
    2. Regarding an open in a CAN branch and a communication stop that is currently occurring, the malfunctioning part can be confirmed easily by performing the CAN bus check using the Techstream because the ECU or sensor connected to the CAN branch does not respond (the ECU or sensor name will not be displayed on the screen).
    3. If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed.



    Sub Bus 15 (Open in one CAN branch line)
    Sub Bus 15 (Open in both CAN branch lines)
    Sub Bus 15 (Open in one CAN main bus line)
    Trouble Mode
    Trouble Mode
    Trouble Mode
    Output ECU
    Output DTC
    Brake Booster with Master Cylinder Assembly (Skid Control ECU) (Click here)
    Brake Booster with Master Cylinder Assembly (Skid Control ECU) (Click here)
    Power Management Control ECU (HV CPU) (Click here)
    CAN J/C LH to Power Management Control ECU (HV CPU)
    CAN J/C LH to ECM
    ECM (Click here)
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0101
    -
    -
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    -
    -
    U0293
    -
    -
    -
    -
    -
    -
    V Bus
    Radio and Display Receiver Assembly*4
    U0073
    -
    -
    -
    -
    -
    -
    U0100
    -
    -
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    -
    -
    U0140
    -
    -
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    -
    -
    U0293
    -
    -
    -
    -
    -
    -
    Multiplex Network Body ECU
    U0100
    -
    -
    -
    -
    -
    -
    U0101
    -
    -
    -
    -
    -
    -
    U0120*1
    -
    -
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    -
    -
    U0164
    -
    -
    -
    -
    -
    -
    U0293
    -
    -
    -
    -
    -
    -
    U0327*1
    -
    -
    -
    -
    -
    -
    Brake Booster with Master Cylinder Assembly (Skid Control ECU)
    U0073
    -
    -
    -
    -
    -
    -
    U0123
    -
    -
    -
    -
    -
    -
    U0124
    -
    -
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    -
    -
    U0293
    -
    -
    -
    -
    -
    -
    Power Management Control ECU (HV CPU)
    U0100
    -
    -
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    -
    -
    U0140*2
    -
    -
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    -
    -
    U0164
    -
    -
    -
    -
    -
    -
    U0293
    -
    -
    -
    -
    -
    -
    U1107*1
    -
    -
    -
    -
    -
    -
    Power Management Control ECU
    (Cruise Control)*3
    U0122
    -
    -
    -
    -
    -
    -
    Power Management Control ECU
    (Power Management CPU)
    U0140
    -
    -
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    -
    -
    U0293
    -
    -
    -
    -
    -
    -
    Power Steering ECU Assembly
    U0129
    -
    -
    -
    -
    -
    -
    U0293
    -
    -
    -
    -
    -
    -
    ECM
    U0293
    -
    -
    -
    -
    -
    -
    V Bus
    Smart Key ECU Assembly (Certification ECU)*1
    U0100
    -
    -
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    -
    -
    U0293
    -
    -
    -
    -
    -
    -
    Combination Meter Assembly
    U0100
    -
    -
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    -
    -
    U0131
    -
    -
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    -
    -
    Spiral Cable with Sensor Sub-assembly (Steering Sensor)
    -
    -
    -
    -
    -
    -
    -
    DLC3
    -
    -
    -
    -
    -
    -
    -
    Sub Bus 15
    ECM
    U0293
    -
    -
    ○
    ○
    ○
    -
    Brake Booster with Master Cylinder Assembly (Skid Control ECU)
    U0073
    ○
    ○
    -
    -
    -
    -
    U0123
    -
    -
    -
    -
    -
    -
    U0124
    -
    -
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    -
    -
    U0293
    -
    -
    ○
    ○
    -
    -
    Power Management Control ECU (HV CPU)
    U0100
    -
    -
    -
    -
    -
    ○
    U0129
    ○
    ○
    -
    -
    -
    ○
    U0140*2
    -
    -
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    -
    -
    U0164
    -
    -
    -
    -
    -
    -
    U1107*1
    -
    -
    -
    -
    -
    -
    Power Management Control ECU
    (Cruise Control)*3
    U0122
    -
    -
    -
    -
    -
    -

    HINT:
    1. ○: Set
    2. -: DTC is not output.
    3. *1: w/ Smart key system
    4. *2: w/o Smart key system
    5. *3: w/ Cruise control system
    6. *4: for Radio and display receiver type
    7. If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed.



    Sub Bus 15 (Open in both CAN main bus lines)
    Trouble Mode
    Output ECU
    Output DTC
    Power Management Control ECU (HV CPU) (Click here)
    CAN J/C LH to Power Management Control ECU (HV CPU)
    CAN J/C LH to ECM
    ECM (Click here)
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0101
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    U0293
    -
    -
    -
    -
    Radio and Display Receiver Assembly*4
    U0073
    -
    -
    -
    -
    U0100
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    U0140
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    U0293
    -
    -
    -
    -
    Multiplex Network Body ECU
    U0100
    -
    -
    -
    -
    U0101
    -
    -
    -
    -
    U0120*1
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    U0164
    -
    -
    -
    -
    U0293
    -
    -
    -
    -
    U0327*1
    -
    -
    -
    -
    Brake Booster with Master Cylinder Assembly (Skid Control ECU)
    U0073
    -
    -
    -
    -
    U0123
    -
    -
    -
    -
    U0124
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    U0293
    -
    -
    -
    -
    Power Management Control ECU (HV CPU)
    U0100
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    U0140*2
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    U0164
    -
    -
    -
    -
    U1107*1
    -
    -
    -
    -
    Power Management Control ECU
    (Cruise Control)*3
    U0122
    -
    -
    -
    -
    Power Management Control ECU
    (Power Management CPU)
    U0140
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    U0293
    -
    -
    -
    -
    V Bus
    Power Steering ECU Assembly
    U0129
    -
    -
    -
    -
    U0293
    -
    -
    -
    -
    ECM
    U0293
    -
    -
    -
    -
    Smart Key ECU Assembly (Certification ECU)*1
    U0100
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    U0293
    -
    -
    -
    -
    Combination Meter Assembly
    U0100
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    U0131
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    Spiral Cable with Sensor Sub-assembly (Steering Sensor)
    -
    -
    -
    -
    -
    DLC3
    -
    -
    -
    -
    -
    Sub Bus 15
    ECM
    U0293
    ○
    ○
    ○
    -
    Brake Booster with Master Cylinder Assembly (Skid Control ECU)
    U0073
    -
    -
    -
    -
    U0123
    -
    -
    -
    -
    U0124
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    U0293
    ○
    ○
    -
    -
    Power Management Control ECU (HV CPU)
    U0100
    -
    -
    -
    ○
    U0129
    -
    -
    -
    ○
    U0140*2
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    U0164
    -
    -
    -
    -
    U1107*1
    -
    -
    -
    -
    Power Management Control ECU
    (Cruise Control)*3
    U0122
    -
    -
    -
    -

    HINT:
    1. ○: Set
    2. -: DTC is not output.
    3. *1: w/ Smart key system
    4. *2: w/o Smart key system
    5. *3: w/ Cruise control system
    6. *4: for Radio and display receiver type
    7. If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed.



    Sub Bus 15 (CAN bus line short circuit)
    Sub Bus 15 (CAN bus line short to GND)
    Trouble Mode
    Trouble Mode
    Output ECU
    Output DTC
    CANH to CANL
    CANH to GND
    CANL to GND
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0101
    -
    -
    -
    U0142
    -
    -
    -
    U0155
    -
    -
    -
    U0293
    -
    -
    -
    Radio and Display Receiver Assembly*4
    U0073
    -
    -
    -
    U0100
    -
    -
    -
    U0129
    -
    -
    -
    U0140
    -
    -
    -
    U0155
    -
    -
    -
    U0293
    -
    -
    -
    Multiplex Network Body ECU
    U0100
    -
    -
    -
    U0101
    -
    -
    -
    U0120*1
    -
    -
    -
    U0151
    -
    -
    -
    U0155
    -
    -
    -
    U0164
    -
    -
    -
    U0293
    -
    -
    -
    U0327*1
    -
    -
    -
    Brake Booster with Master Cylinder Assembly (Skid Control ECU)
    U0073
    -
    -
    -
    U0123
    -
    -
    -
    U0124
    -
    -
    -
    U0126
    -
    -
    -
    U0293
    -
    -
    -
    Power Management Control ECU (HV CPU)
    U0100
    -
    -
    -
    U0129
    -
    -
    -
    U0140*2
    -
    -
    -
    U0151
    -
    -
    -
    U0164
    -
    -
    -
    U1107*1
    -
    -
    -
    Power Management Control ECU
    (Cruise Control)*3
    U0122
    -
    -
    -
    Power Management Control ECU
    (Power Management CPU)
    U0140
    ○
    ○
    ○
    U0155
    ○
    ○
    ○
    U0293
    ○
    ○
    ○
    Power Steering ECU Assembly
    U0129
    -
    -
    -
    U0293
    -
    -
    -
    ECM
    U0293
    -
    -
    -
    V Bus
    Smart Key ECU Assembly (Certification ECU)*1
    U0100
    -
    -
    -
    U0142
    -
    -
    -
    U0155
    -
    -
    -
    U0293
    -
    -
    -
    Combination Meter Assembly
    U0100
    -
    -
    -
    U0129
    -
    -
    -
    U0131
    -
    -
    -
    U0142
    -
    -
    -
    U0151
    -
    -
    -
    Spiral Cable with Sensor Sub-assembly (Steering Sensor)
    -
    -
    -
    -
    DLC3
    -
    -
    -
    -
    Sub Bus 15
    ECM
    U0293
    ○
    ○
    ○
    Brake Booster with Master Cylinder Assembly (Skid Control ECU)
    U0073
    ○
    ○
    ○
    U0123
    -
    -
    -
    U0124
    -
    -
    -
    U0126
    -
    -
    -
    U0293
    -
    -
    -
    Power Management Control ECU (HV CPU)
    U0100
    ○
    ○
    ○
    U0129
    ○
    ○
    ○
    U0140*2
    -
    -
    -
    U0151
    -
    -
    -
    U0164
    -
    -
    -
    U1107*1
    -
    -
    -
    Power Management Control ECU (HV CPU)
    (Cruise Control)*3
    U0122
    -
    -
    -

    HINT:
    1. ○: Set
    2. -: DTC is not output.
    3. *1: w/ Smart key system
    4. *2: w/o Smart key system
    5. *3: w/ Cruise control system
    6. *4: for Radio and display receiver type
    7. If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed.


CAN BUS WAVEFORMS

C230845E02

HINT:
  1. This waveform is measured between terminals CANH and GND, and terminals CANL and GND of the DLC3. (Use this as a reference for diagnosis of CAN communication lines.)
  2. When malfunctions in multiple ECUs are suspected based on the CAN Bus Check and DTCs checked using the Techstream, check the resistance of the CAN bus using an ohmmeter first (Click here). If no problems are found, check the following waveforms.
  3. If a waveform is not similar to one of the following 3 patterns (Group 1), then an open in a CAN main bus line, an open in a CAN branch line, or a short between a CAN line (CANH or CANL) and ground is suspected (Group 2).
  4. Wiggle the connector and wire harness to check if the waveform changes.



  1. CAN bus waveforms (Group 1)



      C227926E01
    1. Normal waveform



    2. C239096E01
    3. Open in both of the lines (CANH and CANL) of a CAN branch

      HINT:
      1. Waveforms (waveforms shown using dotted lines) are not present from an ECU or sensor connected to a CAN branch with an open circuit in both lines. (Waveforms from other ECUs or sensors are normal.)
      2. Because this waveform is similar to a normal waveform, instead of using the waveform, the malfunctioning part can be narrowed down by performing a CAN bus check.



    4. C227930E01
    5. Short between the CAN bus lines (CANH and CANL)

      HINT:
      1. Waveforms disappear.
      2. If the malfunction is in an ECU, disconnecting the ECU will change the waveform. If the waveform does not change, a malfunction in the wire harness is suspected.



  2. CAN bus waveforms (reference) (Group 2)

    NOTICE:
    The following CAN bus waveforms can be used only as reference. The actual measured waveform may differ significantly depending on the location of the open or short circuit.




      C227931E01
    1. Open in a CAN branch line (CANH)

      HINT:
      1. An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.
      2. Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.



    2. C227932E01
    3. Open in a CAN branch line (CANL)

      HINT:
      1. An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.
      2. Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.



    4. C227927E01
    5. Open in a CAN main bus line (CANH)

      HINT:
      1. Waveforms of ECUs or sensors that are nearer to the DLC3 than the open part are almost normal.
      2. Waveforms of ECUs or sensors that are on the opposite side of the DLC3 from the open part are abnormal.
      3. An open in a CAN main bus line can be confirmed by measuring the resistance between the CANH and CANL terminals of any CAN branch.



    6. C227928E01
    7. Short between a CAN bus line (CANH) and ground

      HINT:
      1. Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connector or when disconnecting ECUs or sensors.
      2. A short to ground in the CANH line can be confirmed by measuring the resistance between CANH and ground using an ohmmeter.



    8. C227929E01
    9. Short between a CAN bus line (CANL) and ground

      HINT:
      1. Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connector or when disconnecting ECUs or sensors.
      2. A short to ground in the CANL line can be confirmed by measuring the resistance between CANL and ground using an ohmmeter.


DATA SENDING/RECEIVING TABLE
  1. Data sending/receiving table

    HINT:
    If Data List items related to sent/received data are not displayed properly, the part for which communication is interrupted can be determined using the table below.

    Data content
    Data Detected and Sent by
    Data Received by
    (Can be Checked in Data List)
    Data Received by
    (Cannot be Checked in Data List)
    Relevant Data List Item
    [Selected System]
    Accelerator position
    Power management control ECU (HV CPU)
    -
    Combination meter assembly
    Accelerator Degree [Hybrid Control]
    Engine speed
    ECM
    -
    1. Airbag sensor assembly
    2. Air conditioning amplifier assembly
    3. Main body ECU (Multiplex network body ECU)
    4. Combination meter assembly
    Engine Speed [Engine and ECT]
    Engine coolant temperature
    ECM
    1. Air conditioning amplifier assembly
    2. Combination meter assembly
    -
    1. Coolant Temp [Engine and ECT]
    2. Engine Coolant Temp [Air Conditioner]
    3. Coolant Temperature [Combination Meter]
    Vehicle speed
    Brake booster with master cylinder assembly (Skid control ECU)
    1. Power management control ECU (HV CPU)
    2. Combination meter assembly*3
    3. Power steering ECU assembly
    1. Airbag sensor assembly
    2. Radio and display receiver assembly
    1. Vehicle Speed [ABS/VSC/TRAC]
    2. Vehicle Spd [Hybrid Control]
    3. Vehicle Speed Meter [Combination Meter]
    4. Meter Vehicle Velocity [EMPS]
    Combination meter assembly*3
    -
    1. Power management control ECU (Power management CPU)
    2. Air conditioning amplifier assembly
    3. Main body ECU (Multiplex network body ECU)
    4. Smart key ECU assembly (Certification ECU)
    Vehicle Speed Meter [Combination Meter]
    Shift position
    Power management control ECU (HV CPU)
    Radio and display receiver assembly
    1. Power management control ECU (Power management CPU)
    2. Airbag sensor assembly
    3. Main body ECU (Multiplex network body ECU)
    4. Combination meter assembly*2
    5. Air conditioning amplifier assembly
    1. Shift Sensor Shift Pos [Hybrid Control]
    2. Reverse Signal [Navigation System]
    Ambient temperature
    Air conditioning amplifier assembly
    1. Power management control ECU (HV CPU)
    2. ECM
    3. Combination meter assembly
    Main body ECU (Multiplex network body ECU)
    1. Ambient Temp Sensor [Air Conditioner]
    2. Ambient Temperature [Hybrid Control]
    3. Ambient Temp for A/C [Engine and ECT]
    4. Ambient Temperature [Combination Meter]
    Driver door courtesy
    Main body ECU (Multiplex network body ECU)
    -
    1. Power management control ECU (HV CPU)
    2. Power management control ECU (Power management CPU)
    3. Smart key ECU assembly (Certification ECU)
    4. Combination meter assembly*2
    FL Door Courtesy SW [Main Body]
    Steering angle sensor
    Spiral cable with sensor sub-assembly (Steering sensor)
    Brake booster with master cylinder assembly (Skid control ECU)
    Airbag sensor assembly
    Steering Angle Sensor [ABS/VSC/TRAC]
    Yaw rate sensor
    Airbag sensor assembly (built-in type yaw rate sensor)
    Brake booster with master cylinder assembly (Skid control ECU)
    -
    1. Yaw Rate Sensor [ABS/VSC/TRAC]
    2. Yaw Rate Sensor2 [ABS/VSC/TRAC]
    Deceleration sensor
    Airbag sensor assembly (built-in type yaw rate sensor)
    Brake booster with master cylinder assembly (Skid control ECU)
    Power management control ECU (HV CPU)
    1. Deceleration Sensor [ABS/VSC/TRAC]
    2. Deceleration Sensor2 [ABS/VSC/TRAC]
    Power management control ECU (HV CPU) power source voltage
    Power management control ECU (HV CPU)*1
    -
    -
    +B [Hybrid Control]
    Power management control ECU (Power Management CPU) power source state
    Power management control ECU (Power management CPU)*1
    -
    -
    Power Supply Condition [Power Source Control]
    ECM power source voltage
    ECM*1
    -
    -
    Battery Voltage [Engine and ECT]
    Brake pedal stroke sensor
    Brake booster with master cylinder assembly (Skid control ECU)*1
    -
    -
    1. Stroke Sensor [ABS/VSC/TRAC]
    2. Stroke Sensor2 [ABS/VSC/TRAC]
    Power steering ECU assembly power source voltage
    Power steering ECU assembly*1
    -
    -
    IG Power Supply [EMPS]
    Intensity of light received by the solar sensor
    Air conditioning amplifier assembly*1
    -
    -
    Solar Sensor (D Side) [Air Conditioner]
    Combination meter assembly power source voltage
    Combination meter assembly*1
    -
    -
    +B Voltage Value [Combination Meter]
    Radio and display receiver assembly power source voltage
    Radio and display receiver assembly*1
    -
    -
    Battery Voltage [Navigation System]
    Driver door touch sensor
    Smart key ECU assembly (Certification ECU)*1
    -
    -
    D-Door Touch Sensor [Smart Key]

    *1: Whether the ECU that sends data is functioning or not can be judged by using the Techstream to check items such as switches or sensors that send signals to the ECU via direct lines.
    *2: Although the received contents cannot be checked in the Data List, whether or not the data is received normally can be checked by observing the combination meter.
    *3: The combination meter assembly receives a vehicle speed signal from the brake booster with master cylinder assembly (skid control ECU)*1 and sends the signal to other ECUs.

  2. Details of relevant Data List items (Selected system: Hybrid Control)

    NOTICE:
    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    HINT:
    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch ON (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Data List.

    4. Check the results by referring to the following table.

      Hybrid Control 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Vehicle Spd
      Vehicle speed/
      Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
      Vehicle stopped:
      0 km/h (0 mph)
      While driving at a constant speed:
      No significant fluctuation
      -
      +B
      Auxiliary battery voltage/
      Min.: 0.00 V, Max.: 65.53 V
      Constant:
      10.00 to 15.00 V
      Auxiliary battery condition
      Accelerator Degree
      Accelerator pedal depressed angle/
      Min.: 0.0%, Max.: 100.0%
      Accelerator pedal depressed:
      Changes with accelerator pedal pressure
      Accelerator pedal sensor assembly
      Ambient Temperature
      Ambient air temperature/
      Min.: -40°C (-40°F), Max.: 215°C (419°F)
      Ignition switch ON (IG):
      Same as ambient air temperature
      Ambient temperature sensor
      Shift Sensor Shift Pos
      Shift position/
      P/R/N/D/B
      Matches currently selected shift position:
      P, R, N, D or B
      Shift lever position sensor

  3. Details of relevant Data List items (Selected system: Power Source Control)

    NOTICE:
    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    HINT:
    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch ON (IG).

    3. Turn the Techstream on.

    4. Enter the following menus: Body Electrical / Power Source Control / Data List.

    5. Check the results by referring to the following table.

      Power Source Control 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Power Supply Condition
      Power supply state/IG2 ON, ST ON, All OFF, IG1 ON or ACC ON
      All OFF: Ignition switch off (ACC and IG)
      ACC ON: Ignition switch to ACC
      IG1 ON: Ignition switch ON (IG) (IG1 relay on)
      IG2 ON: Ignition switch ON (IG) (IG2 relay on)
      ST ON: Sending hybrid control system start request signal
      Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time).

  4. Details of relevant Data List items (Selected system: Engine and ECT)

    NOTICE:
    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    HINT:
    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    HINT:
    Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in N or P, the A/C switch should be off and all accessory switches should be off.


    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch ON (IG).

    3. Turn the Techstream on.

    4. Put the engine in inspection mode (maintenance mode) (Click here).

    5. Warm up the engine.

    6. Turn the A/C switch off.

    7. Turn the ignition switch off.

    8. Turn the ignition switch ON (IG).

    9. Turn the Techstream on.

    10. Enter the following menus: Powertrain / Engine and ECT / Data List.

    11. According to the display on the Techstream, read the Data List.

      Engine and ECT 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Engine Speed
      Engine speed/
      Min.: 0 rpm, Max.: 16383 rpm
      950 to 1050 rpm: Idling
      When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
      Coolant Temp
      Coolant temperature/
      Min.: -40°C (-40°F), Max.: 140°C (284°F)
      75 to 100°C (167 to 212°F): After warming up
      This is the engine coolant temperature.

      HINT:
      1. After warming up the engine, the engine coolant temperature is 75 to 100°C (167 to 212°F).
      2. After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.
      3. If the value is -40°C (-40°F), or 135°C (275°F), the sensor circuit is open or shorted.
      4. Check if the engine overheats when the value indicates 135°C (275°F).

      Battery Voltage
      Auxiliary battery voltage/
      Min.: 0 V, Max.: 65.535 V
      11 to 16 V: Ignition switch ON (IG)
      If 11 V or less, characteristics of some electrical components may change.
      Ambient Temp for A/C
      Ambient temperature for A/C/
      Min.: -40°C (-40°F), Max.: 215°C (419°F)
      -
      -

  5. Details of relevant Data List items (Selected system: ABS/VSC/TRAC)

    NOTICE:
    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    HINT:
    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


    1. Warm up the engine.

    2. Turn the ignition switch off.

    3. Connect the Techstream to the DLC3.

    4. Turn the ignition switch ON (IG).

    5. Turn the Techstream on.

    6. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

    7. According to the display on the Techstream, read the Data List.

      ABS/VSC/TRAC 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Stroke Sensor
      Brake pedal stroke sensor assembly / Min.: 0.00 V, Max.: 5.00 V
      When brake pedal released: 0.65 to 1.35 V
      Reading increases when brake pedal is depressed
      Stroke Sensor2
      Brake pedal stroke sensor assembly 2 / Min.: 0.00 V, Max.: 5.00 V
      When brake pedal released: 3.65 to 4.35 V
      Reading decreases when brake pedal is depressed
      Deceleration Sensor
      Acceleration sensor 1 / Min.: -18.525 m/s2, Max.: 18.387 m/s2
      -
      During deceleration/acceleration: Changes continuously
      Deceleration Sensor2
      Acceleration sensor 2 / Min.: -18.525 m/s2, Max.: 18.387 m/s2
      -
      During deceleration/acceleration: Changes continuously
      Yaw Rate Sensor
      Yaw rate sensor 1 / Min.: -128 degrees/s, Max.: 127 degrees/s
      Vehicle stationary: 0 degrees/s
      Turning right: -128 to 0 degrees/s
      Turning left: 0 to 127 degrees/s
      -
      Yaw Rate Sensor2
      Yaw rate sensor 2 / Min.: -128 degrees/s, Max.: 127 degrees/s
      Vehicle stationary: 0 degrees/s
      Turning right: -128 to 0 degrees/s
      Turning left: 0 to 127 degrees/s
      -
      Steering Angle Sensor
      Steering angle sensor / Min.: -3276.8 degrees, Max.: 3276.7 degrees
      Turning left: Increases
      Turning right: Decreases
      -
      Vehicle Speed
      Maximum wheel speed sensor / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
      Vehicle stopped: 0 km/h (0 mph)
      When driving at constant speed: No large fluctuations

  6. Details of relevant Data List items (Selected system: EMPS)

    NOTICE:
    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    HINT:
    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


    1. Turn the ignition switch off.

    2. Connect the Techstream to the DLC3.

    3. Turn the ignition switch ON (IG).

    4. Turn the Techstream on.

    5. Enter the following menus: Chassis / EMPS / Data List.

    6. According to the display on the Techstream, read the Data List.

      EMPS 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Meter Vehicle Velocity
      Vehicle speed from meter/
      Min.: 0.0 km/h (0.0 mph)
      Max.: 300.0 km/h (186.4 mph)
      0 km/h (0 mph)
      Ignition switch ON (READY) and vehicle stopped
      No significant fluctuation
      Ignition switch ON (READY) and vehicle driven at a constant speed
      IG Power Supply
      ECU power source voltage/
      Min.: 0.0000 V
      Max.: 20.1531 V
      9 to 16 V
      Ignition switch ON

  7. Details of relevant Data List items (Selected system: Navigation System)

    NOTICE:
    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    HINT:
    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch ON (READY).

    3. Turn the Techstream on.

    4. Enter the following menus: Body Electrical / Navigation System / Data List.

    5. According to the display on the Techstream, read the Data List.

      Navigation System 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Battery Voltage
      Auxiliary battery voltage/ Min.: 0 V, Max.:24 V
      11 to 15.5 V
      -
      Reverse Signal
      Reverse signal/ON or OFF
      ON: Reverse selected
      OFF: Reverse not selected
      -

  8. Details of relevant Data List items (Selected system: Smart Key)

    NOTICE:
    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    HINT:
    1. Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
    2. When using the Techstream with the ignition switch off to troubleshoot:
      Connect the Techstream to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the Techstream and vehicle begins.


    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch ON (IG).

    3. Turn the Techstream on.

    4. Enter the following menus: Body Electrical / Smart Key / Data List.

    5. Read the Data List according to the display on the Techstream.

      Smart Key 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      D-Door Touch Sensor
      Driver door touch sensor (unlock sensor) / ON or OFF
      ON: Driver door touch sensor (unlock sensor) touched
      OFF: Driver door touch sensor (unlock sensor) not touched
      1. Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).
      2. Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.

  9. Details of relevant Data List items (Selected system: Combination Meter)

    NOTICE:
    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    HINT:
    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


    1. Warm up the engine.

    2. Turn the ignition switch off.

    3. Connect the Techstream to the DLC3.

    4. Turn the ignition switch ON (IG).

    5. Turn the Techstream on.

    6. Enter the following menus: Body Electrical / Combination Meter / Data List.

      Combination Meter 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Vehicle Speed Meter
      Vehicle speed/Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
      Almost the same as actual vehicle speed
      -
      Coolant Temperature
      Engine coolant temperature/-40 to 127.5°C (-40 to 261.5°F)
      After warming up: 75 to 100°C (167 to 212°F)
      1. After warming up the engine, the engine coolant temperature is 75 to 100°C (167 to 212°F).
      2. After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.
      +B Voltage Value
      Auxiliary battery voltage/Min.: 0 V, Max.: 25.5 V
      11 to 16 V
      -
      Ambient Temperature
      Outside temperature/Min.: -40°C (-40°F), Max.: 87.5°C (189.5°F)
      Almost the same as actual outside temperature
      The temperature displayed on the multi-information display is -40 to 50°C (-40 to 122°F)

  10. Details of relevant Data List items (Selected system: Air Conditioner)

    NOTICE:
    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    HINT:
    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch ON (IG).

    3. Turn the Techstream on.

    4. Enter the following menus: Body Electrical / Air Conditioner / Data List.

    5. Check the value(s) by referring to the table below.

      Air Conditioner 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Ambient Temp Sensor
      Ambient temperature sensor (thermistor assembly) /
      Min.: -23.30°C (-9.94°F)
      Max.: 65.95°C (150.71°F)
      Actual ambient temperature displayed
      -
      Solar Sensor (D Side)
      Solar sensor /
      Min.: 0
      Max.: 255
      Solar sensor value increases as brightness increases
      -
      Engine Coolant Temp
      Engine coolant temperature sensor /
      Min.: 1.30°C (34.34°F)
      Max.: 90.55°C (194.99°F)
      Actual engine coolant temperature displayed
      -

  11. Details of relevant Data List items (Selected system: Main Body (Main Body ECU (Multiplex Network Body ECU))

    NOTICE:
    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    HINT:
    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch ON (IG).

    3. Turn the Techstream on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. Read the Data List according to the display on the Techstream.

      Main Body 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      FL Door Courtesy SW
      Front door courtesy light switch LH signal/ON or OFF
      ON: Front door LH open
      OFF: Front door LH closed
      -