Home › Suspension › REAR SUSPENSION › REAR COIL SPRING

REAR COIL SPRING > INSTALLATION

for Preparation Click here



1. INSTALL REAR LOWER COIL SPRING INSULATOR LH
  1. Install the rear lower coil spring insulator LH onto the rear axle beam assembly.



2. INSTALL REAR LOWER COIL SPRING INSULATOR RH

HINT:
Perform the same procedure as the LH side.



3. INSTALL REAR UPPER COIL SPRING INSULATOR LH


    C110329E04
  1. Install the rear upper coil spring insulator LH so that its gap fits onto the end of rear coil spring LH.
    Text in Illustration 
    *a
    Fit



4. INSTALL REAR UPPER COIL SPRING INSULATOR RH

HINT:
Perform the same procedure as the LH side.



5. INSTALL REAR COIL SPRING LH
  1. Support the spring seat of the rear axle beam assembly using 2 jacks and 2 wooden blocks.

  1. Remove the 2 bolts while holding the 2 nuts and separate the rear axle beam assembly from the rear shock absorber assemblies LH and RH.

    NOTICE:
    Since stopper nuts are used, turn the bolts.

  1. Slowly lower the rear axle beam assembly using 2 jacks and 2 wooden blocks.



    C233115
  1. Install the rear coil spring LH onto the rear axle beam assembly.
    Text in Illustration 
    V100144
    Paint Mark

    NOTICE:
    The paint mark of the rear coil spring LH should be towards the underside and rear side of the vehicle.

  1. Slowly jack up the rear axle beam assembly using 2 jacks and 2 wooden blocks, and temporarily install the rear axle beam assembly and rear coil spring LH with the 2 bolts and 2 nuts.



6. INSTALL REAR COIL SPRING RH

HINT:
Perform the same procedure as the LH side.



7. INSTALL REAR FLEXIBLE HOSE LH
  1. Install the rear flexible hose LH onto the rear axle beam assembly with a new clip.

    NOTICE:
    Install the clip as far as it will go.

  1. Using a union nut wrench, install the rear flexible hose LH to the brake tube while holding the rear flexible hose LH with a wrench.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    1. Do not bend or damage the brake line.
    2. Do not allow any foreign matter such as dirt and dust to enter the brake line from the connecting points.
    3. Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



8. INSTALL REAR FLEXIBLE HOSE RH

HINT:
Perform the same procedure as the LH side.



9. INSTALL SKID CONTROL SENSOR WIRE LH
  1. Install the skid control sensor wire LH to the rear axle beam assembly with the nut.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



10. INSTALL SKID CONTROL SENSOR WIRE RH

HINT:
Perform the same procedure as the LH side.



11. CONNECT SKID CONTROL SENSOR WIRE LH


    C235058
  1. Install the skid control sensor wire connector to the connector cover.



    C235580
  1. Engage the 3 claws to secure the connector cover.

  1. Connect the skid control sensor wire connector to the rear axle hub and bearing assembly.



12. CONNECT SKID CONTROL SENSOR WIRE RH

HINT:
Perform the same procedure as the LH side.



13. INSTALL REAR WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



14. STABILIZE SUSPENSION
  1. Lower the vehicle from the jack.

  1. Bounce the vehicle up and down several times to stabilize the suspension.



15. FULLY TIGHTEN REAR AXLE BEAM ASSEMBLY


    C249972E01
  1. Suspend the jack on the spring seat of the rear axle beam assembly and adjust the length of the rear shock absorber assembly to the reference value.
    Text in Illustration 
    *A
    LH Side
    *B
    RH Side

    Length of shock absorber:
    220 mm (8.66 in.)

  1. Fully tighten the 2 bolts.

    Torque:
    90 N*m{ 918 kgf*cm , 66 ft.*lbf }



16. FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY LH
  1. Fully tighten the rear shock absorber assembly (lower side) with the bolt.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

    NOTICE:
    Since a stopper nut is used, turn the bolt.



17. FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY RH

HINT:
Perform the same procedure as the LH side.



18. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL



19. BLEED BRAKE LINE
(Click here)


20. INSPECT REAR WHEEL ALIGNMENT
(Click here)


21. CHECK SPEED SENSOR SIGNAL
(Click here)