REAR AXLE BEAM > INSTALLATION |
| 1. TEMPORARILY TIGHTEN REAR AXLE BEAM ASSEMBLY |
Slowly jack up the rear axle beam assembly with an engine lifter using 2 wooden blocks and 2 attachments or equivalent tools and temporarily install the rear axle beam assembly to the body with the 2 bolts (B).

| *1 | Engine Lifter | *2 | Wooden Block |
| *3 | Attachment | - | - |
Temporarily tighten the rear axle beam assembly to the rear shock absorber assemblies LH and RH with the 2 bolts (A) and 2 nuts.
| 2. INSTALL REAR LOWER COIL SPRING INSULATOR LH |
Install the rear lower coil spring insulator LH onto the rear axle beam assembly.
| 3. INSTALL REAR LOWER COIL SPRING INSULATOR RH |
| 4. INSTALL REAR UPPER COIL SPRING INSULATOR LH |
![]() |
Install the rear upper coil spring insulator LH so that its gap fits onto the end of rear coil spring LH.
| *a | Fit |
| 5. INSTALL REAR UPPER COIL SPRING INSULATOR RH |
| 6. INSTALL REAR COIL SPRING LH |
Support the spring seat of the rear axle beam assembly using 2 jacks and 2 wooden blocks.
Remove the 2 bolts while holding the 2 nuts and separate the rear axle beam assembly from the rear shock absorber assemblies LH and RH.
Slowly lower the rear axle beam assembly using 2 jacks and 2 wooden blocks.
![]() |
Install the rear coil spring LH onto the rear axle beam assembly.
![]() | Paint Mark |
Slowly jack up the rear axle beam assembly using 2 jacks and 2 wooden blocks, and temporarily install the rear axle beam assembly and rear coil spring LH with the 2 bolts and 2 nuts.
| 7. INSTALL REAR COIL SPRING RH |
| 8. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH |
Install the rear axle hub and bearing assembly to the rear axle beam assembly with the 4 bolts.
| 9. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY RH |
| 10. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY |
Install the 2 rear brake drum sub-assemblies .
| 11. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY |
Install the new No. 1 parking brake cable clamp to the No. 3 parking brake cable assembly .
Install the No. 3 parking brake cable assembly with the bolt and a No. 1 parking brake cable clamp.
| 12. INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY |
| 13. INSTALL NO. 4 REAR BRAKE TUBE |
Install the No. 4 rear brake tube to the rear axle beam assembly with the nut.
Connect the rear flexible hose LH to the rear axle beam assembly with a new clip.
Using a union nut wrench, install the No. 4 rear brake tube to the rear flexible hose LH while holding the rear flexible hose LH with a wrench.
| 14. INSTALL NO. 3 REAR BRAKE TUBE |
| 15. INSTALL SKID CONTROL SENSOR WIRE LH |
Install the skid control sensor wire LH to the rear axle beam assembly with the nut.
| 16. INSTALL SKID CONTROL SENSOR WIRE RH |
| 17. CONNECT SKID CONTROL SENSOR WIRE LH |
![]() |
Install the skid control sensor wire connector to the connector cover.
![]() |
Engage the 3 claws to secure the connector cover.
Connect the skid control sensor wire connector to the rear axle hub and bearing assembly.
| 18. CONNECT SKID CONTROL SENSOR WIRE RH |
| 19. ADJUST REAR DRUM BRAKE SHOE CLEARANCE |
![]() |
Temporarily install the 2 wheel nuts.
![]() | Expand |
Remove the shoe adjusting hole plug, and turn the adjuster to expand the shoe until the drum locks.
![]() |
Hold the automatic adjust lever away from the adjuster, and contract the brake shoe by turning the adjust bolt using another screwdriver until the drum can rotate smoothly.
| *1 | Automatic Adjust Lever |
![]() | Contract |
Install the hole plug.
| 20. INSTALL REAR WHEEL |
| 21. STABILIZE SUSPENSION |
Lower the vehicle from the jack.
Bounce the vehicle up and down several times to stabilize the suspension.
| 22. FULLY TIGHTEN REAR AXLE BEAM ASSEMBLY |
![]() |
Suspend the jack on the spring seat of the rear axle beam assembly and adjust the length of the rear shock absorber assembly to the reference value.
| *A | LH Side |
| *B | RH Side |
Fully tighten the 2 bolts.
| 23. FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY LH |
Fully tighten the rear shock absorber assembly (lower side) with the bolt.
| 24. FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY RH |
| 25. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL |
| 26. BLEED BRAKE LINE |
| 27. INSPECT REAR WHEEL ALIGNMENT |
| 28. CHECK FOR SPEED SENSOR SIGNAL |