Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Smart Key System)

WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Smart Key System) > No Answer-Back

for Preparation Click here


DESCRIPTION

In some cases, wireless door lock control functions are normal but the hazard warning light and/or wireless door lock buzzer answer-back function does not operate. In such cases, hazard warning light and wireless door lock buzzer signal outputs from the main body ECU (multiplex network body ECU) may be malfunctioning.

WIRING DIAGRAM


B281171E20


INSPECTION PROCEDURE

NOTICE:
The wireless door lock control system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (Click here).

1.READ VALUE USING TECHSTREAM (ANSWER-BACK OPERATION)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Customize Setting / Wireless Door Lock.

  1. Select the setting by referring to the table below.

    Display
    Default
    Content
    Setting
    Relevant ECU
    Hazard Answer Back
    ON
    When the doors are locked by wireless operation, the hazard warning lights flash once.
    When the doors are unlocked by wireless operation, the hazard warning lights flash twice.
    OFF or ON
    Main body ECU (Multiplex network body ECU)
    Wireless Buzzer Resp
    ON
    Wireless door lock buzzer response
    OFF or ON
    Main body ECU (Multiplex network body ECU)
    Wireless Buzzer Vol
    Level 7
    Wireless door lock buzzer volume
    Level 7, Level 6, Level 5, Level 4, Level 3, Level 2, Level 1 or Level 0
    Main body ECU (Multiplex network body ECU)

    Result:
    Result
    Proceed to
    Both items are ON and not set to Level 0
    A
    Either item is OFF or set to Level 0
    B



B
PERFORM CUSTOMIZE FUNCTION (Click here)
A


2.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS
  1. Check the wireless door lock control function using the electrical key transmitter sub-assembly.

    Result:
    Result
    Proceed to
    Wireless door lock/unlock operates normally.
    A
    Wireless door lock/unlock does not operate normally.
    B



B
GO TO PROBLEM SYMPTOMS TABLE (Click here)
A


3.READ VALUE USING TECHSTREAM (DOOR UNLOCK DETECTION SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. Read the Data List according to the display on the Techstream.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Door Lock Pos
    Front door RH unlock detection switch signal/LOCK or UNLOCK
    LOCK: Front door RH locked
    UNLOCK: Front door RH unlocked
    -
    FL Door Lock Pos
    Front door LH unlock detection switch signal/LOCK or UNLOCK
    LOCK: Front door LH locked
    UNLOCK: Front door LH unlocked
    -
    RR-Door Lock Pos SW*1
    Rear door RH and LH unlock detection switch signal/ON or OFF
    ON: Rear door RH or LH unlocked
    OFF: Rear door RH and LH locked
    -
    RL-Door Lock Pos SW*2
    Rear door RH and LH unlock detection switch signal/ON or OFF
    ON: Rear door RH or LH unlocked
    OFF: Rear door RH and LH locked
    -

    1. *1: When checking RR- Door Lock Pos SW, make sure to check it with the rear door LH locked.
    2. *2: When checking RL- Door Lock Pos SW, make sure to check it with the rear door RH locked.

    OK:
    The Techstream should display as shown in the table according to door lock operation.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for Driver door)
    B
    NG (for Front Passenger door)
    C
    NG (for Rear LH door)
    D
    NG (for Rear RH door)
    E



B
GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit) (Click here)

C
GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit) (Click here)

D
GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit) (Click here)

E
GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit) (Click here)
A


4.CHECK WIRELESS ANSWER-BACK OPERATION
  1. Check the wireless answer-back operation using the electrical key transmitter sub-assembly.

    Result:
    Result
    Proceed to
    Only wireless door lock buzzer answer-back does not occur.
    A
    Only hazard warning light answer-back does not occur.
    B



B
Go to step 10
A


5.PERFORM ACTIVE TEST USING TECHSTREAM (WIRELESS DOOR LOCK BUZZER)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Active Test.

  1. Perform the Active Test according to the display on the Techstream.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Wireless Buzzer
    Wireless door lock buzzer
    OFF/ON
    -

    Result:
    Result
    Proceed to
    Wireless door lock buzzer does not turn on/off.
    A
    Wireless door lock buzzer turns on/off.
    B



B
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
A


6.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the A28 wireless door lock buzzer and 3C instrument panel junction block assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A28-1 (B) - 3C-34
    Always
    Below 1 Ω
    A28-2 (E) - Body ground
    Always
    Below 1 Ω
    A28-1 (B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


  1. Remove the instrument panel junction block assembly (Click here).


    B217457E23


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3C-34 - MB-21 (BZR)
    Always
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK


8.REPLACE WIRELESS DOOR LOCK BUZZER
  1. Temporarily replace the wireless door lock buzzer with a new one (Click here).


NEXT


9.CHECK WIRELESS DOOR LOCK BUZZER OPERATION
  1. Check the operation of the wireless answer-back function.

    OK:
    Wireless answer-back function operates normally.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (WIRELESS DOOR LOCK BUZZER WAS DEFECTIVE) 

10.HAZARD WARNING LIGHTS OPERATION
  1. Check that the hazard warning light blinks when the hazard warning signal switch is pressed.

    OK:
    Hazard warning light signal is normal.



NG
GO TO LIGHTING SYSTEM (Proceed to Hazard Warning Switch Circuit) (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)