Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Door Unlock Detection Switch Circuit

for Preparation Click here


DESCRIPTION

The main body ECU (multiplex network body ECU) detects the condition of each door unlock detection switch.

WIRING DIAGRAM


E212453E07


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. Read the display on the Techstream.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Door Lock Pos
    Front door RH unlock detection switch signal/LOCK or UNLOCK
    LOCK: Front door RH locked
    UNLOCK: Front door RH unlocked
    -
    FL Door Lock Pos
    Front door LH unlock detection switch signal/LOCK or UNLOCK
    LOCK: Front door LH locked
    UNLOCK: Front door LH unlocked
    -
    RR-Door Lock Pos SW*1
    Rear door RH unlock detection switch signal/ON or OFF
    ON: Rear door LH locked and rear door RH unlocked
    ON: Rear door LH unlocked and rear door RH locked
    ON: Rear door LH and rear door RH unlocked
    OFF: Rear door LH and rear door RH locked
    -
    RL-Door Lock Pos SW*1
    Rear door LH unlock detection switch/ON or OFF
    ON: Rear door LH locked and rear door RH unlocked
    ON: Rear door LH unlocked and rear door RH locked
    ON: Rear door LH and rear door RH unlocked
    OFF: Rear door LH and rear door RH locked
    -

    1. *1: w/ Smart Key System

    Result:

    Result
    Proceed to
    OK
    A
    Front door unlock detection switch LH does not operate
    B
    Front door unlock detection switch RH does not operate
    C
    Rear door unlock detection switch LH and rear door unlock detection switch RH do not operate
    D



B
Go to step 2

C
Go to step 4

D
Go to step 6
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT FRONT DOOR LOCK ASSEMBLY LH
  1. Remove the front door lock assembly LH (Click here).

  1. Inspect the front door lock assembly LH (Click here).

    OK:
    Front door lock assembly LH is normal.



NG
REPLACE FRONT DOOR LOCK ASSEMBLY LH (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK ASSEMBLY LH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
  1. Disconnect the G59 main body ECU (multiplex network body ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J6-8 (LSSR) - G59-7 (LSFL)
    Always
    Below 1 Ω
    J6-8 (LSSR) - Body ground
    Always
    10 kΩ or higher
    J6-7 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

4.INSPECT FRONT DOOR LOCK ASSEMBLY RH
  1. Remove the front door lock assembly RH (Click here).

  1. Inspect the front door lock assembly RH (Click here).

    OK:
    Front door lock assembly RH is normal.



NG
REPLACE FRONT DOOR LOCK ASSEMBLY RH (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK ASSEMBLY RH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
  1. Disconnect the G59 main body ECU (multiplex network body ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H6-7 (LSSR) - G59-18 (LSFR)
    Always
    Below 1 Ω
    H6-7 (LSSR) - Body ground
    Always
    10 kΩ or higher
    H6-8 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

6.INSPECT REAR DOOR LOCK ASSEMBLY LH
  1. Remove the rear door lock assembly LH (Click here).

  1. Inspect the rear door lock assembly LH (Click here).

    OK:
    Rear door lock assembly LH is normal.



NG
REPLACE REAR DOOR LOCK ASSEMBLY LH (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (REAR DOOR LOCK ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)
  1. Disconnect the 3D instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L3-6 (LSSR) - 3D-24
    Always
    Below 1 Ω
    L3-6 (LSSR) - Body ground
    Always
    10 kΩ or higher
    L3-9 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT REAR DOOR LOCK ASSEMBLY RH
  1. Remove the rear door lock assembly RH (Click here).

  1. Inspect the rear door lock assembly RH (Click here).

    OK:
    Rear door lock assembly RH is normal.



NG
REPLACE REAR DOOR LOCK ASSEMBLY RH (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (REAR DOOR LOCK ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)
  1. Disconnect the 3D instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K3-6 (LSSR) - 3D-25
    Always
    Below 1 Ω
    K3-6 (LSSR) - Body ground
    Always
    10 kΩ or higher
    K3-9 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly (Click here).

  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.



  1. Measure the resistance according to the value(s) in the table below.


    E173023E18


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3D-24 - MB-5 (LSR)
    Always
    Below 1 Ω
    3D-25 - MB-5 (LSR)
    Always
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)