Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM

DYNAMIC RADAR CRUISE CONTROL SYSTEM > Distance Control Switch Circuit

for Preparation Click here


DESCRIPTION

The distance control switch sets the vehicle-to-vehicle distance control mode. The distance control switch is installed in the steering pad switch assembly*1 or steering pad switch RH*2. The vehicle-to-vehicle distance set value can be changed by operating the steering pad switch assembly (distance control switch)*1 or steering pad switch RH (distance control switch)*2 while the dynamic radar cruise control system is operating.
  1. *1: Before October, 2010
  2. *2: From October, 2010

WIRING DIAGRAM


Before October, 2010

E169168E12


From October, 2010

E169168E24


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (DISTANCE CONTROL SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Cruise / Data List / Distance Control Switch.

  1. Check the Data List proper functioning of the distance control switch.

    Radar Cruise:

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Distance Control Switch
    Distance control switch signal/ON or OFF
    ON: Distance control switch on
    OFF: Distance control switch off
    -

    OK:
    When the distance control switch is operated, the display changes as shown above.

  1. Proceed to the next step based on the inspection result.

    Result:
    Result
    Proceed to
    OK
    A
    NG (Before October, 2010)
    B
    NG (From October, 2010)
    C



B
Go to step 2

C
Go to step 3
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT STEERING PAD SWITCH ASSEMBLY
  1. Remove the steering pad switch assembly (Click here).



  1. Disconnect the z9 connector from the spiral cable.


    A219719E02


    Text in Illustration 
    *1
    Component without harness connected
    (Steering Pad Switch Assembly)
    *2
    Distance Control Switch

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    z9-4 - z9-6
    Distance control switch ON
    Below 2.5 Ω
    z9-4 - z9-6
    Distance control switch OFF
    10 kΩ or higher

  1. Reinstall the steering pad switch assembly (Click here).

  1. Proceed to the next step based on the inspection result.

    Result:
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 4
A

REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)  

3.INSPECT STEERING PAD SWITCH RH
  1. Remove the steering pad switch RH (Click here).



  1. Disconnect the z9 connector from the spiral cable.


    E257610E01


    Text in Illustration 
    *1
    Component without harness connected
    (Steering Pad Switch RH)
    *2
    Distance Control Switch

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    z9-4 - z9-6
    Distance control switch ON
    Below 2.5 Ω
    z9-4 - z9-6
    Distance control switch OFF
    10 kΩ or higher

  1. Reinstall the steering pad switch RH (Click here).



NG
REPLACE STEERING PAD SWITCH RH (Click here)
OK


4.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

NOTICE:
The spiral with sensor cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral with sensor cable sub-assembly may cause airbag deployment. Be sure to read the page shown in the brackets.



    E144333E64
  1. Remove the spiral with sensor cable sub-assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z9-4 - L52-11 (DIST)
    The spiral with sensor cable sub-assembly is centered
    Below 1 Ω
    The spiral with sensor cable sub-assembly position is 2.5 rotations to the left
    The spiral with sensor cable sub-assembly position is 2.5 rotations to the right
    z9-6 - L52-2 (ECC)
    The spiral with sensor cable sub-assembly is centered
    Below 1 Ω
    The spiral with sensor cable sub-assembly position is 2.5 rotations to the left
    The spiral with sensor cable sub-assembly position is 2.5 rotations to the right

    Text in Illustration 
    *1
    Component without harness connected
    (Spiral with Sensor Cable Sub-assembly)

HINT:
The spiral with sensor cable sub-assembly makes a maximum of approximately 5 rotations.

  1. Install the spiral with sensor cable sub-assembly (Click here).



NG
REPLACE SPIRAL WITH CABLE SUB-ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU)


    E187993E04
  1. Disconnect the driving support ECU connector.

  1. Disconnect the spiral with sensor cable sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L60-6 (SPSW) - L52-11 (DIST)
    Always
    Below 1 Ω
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Spiral with Sensor Cable Sub-assembly)
    *2
    Front view of wire harness connector
    (to Driving Support ECU)

  1. Reconnect the driving support ECU connector.

  1. Reconnect the spiral with sensor cable sub-assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU)
OK


6.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - BODY GROUND)


    E171248E12
  1. Disconnect the spiral with sensor cable sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    L52-2 (ECC) - Body ground
    Always
    Below 1 Ω
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Spiral with Sensor Cable Sub-assembly)

  1. Reconnect the spiral with sensor cable sub-assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - BODY GROUND)
OK

REPLACE DRIVING SUPPORT ECU (Click here)