DTC P0300 Random / Multiple Cylinder Misfire Detected |
DTC P0301 Cylinder 1 Misfire Detected |
DTC P0302 Cylinder 2 Misfire Detected |
DTC P0303 Cylinder 3 Misfire Detected |
DTC P0304 Cylinder 4 Misfire Detected |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0300 | Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip detection logic).
|
|
| P0301 P0302 P0303 P0304 | Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic).
|
| Engine Speed | Duration |
| Idling | 4.5 minutes or more |
| 1000 | 4.5 minutes or more |
| 2000 | 2.5 minutes or more |
| 3000 | 1.5 minutes or more |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0300, P0301, P0302, P0303 and/or P0304 are output | A |
| DTC P0300, P0301, P0302, P0303 and/or P0304 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK PCV HOSE CONNECTIONS |
Check the PCV hose connections (Click here).
|
| ||||
| OK | |
| 3.READ VALUE USING INTELLIGENT TESTER (MISFIRE RPM AND MISFIRE LOAD) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Misfire RPM and Misfire Load.
Read and note the Misfire RPM and Misfire Load values.
| NEXT | |
| 4.READ VALUE USING INTELLIGENT TESTER (CYLINDER #1 (TO #4) MISFIRE COUNT) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Put the engine in inspection mode (maintenance mode) (Click here).
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Cylinder #1 (to #4) Misfire Count.
Start the engine and allow the engine to idle.
Read each value for Cylinder #1 (to #4) Misfire Count displayed on the intelligent tester. If no misfire counts occur in any cylinders, perform steps [A] and [B], and then check the misfire counts again.
Drive the vehicle with the Misfire RPM and Misfire Load noted in the read value using the intelligent tester (Misfire RPM and Misfire Load) procedures above [A].
Read Cylinder #1 (to #4) Misfire Count or the DTCs displayed on the tester [B].
| Misfire Count | Proceed to |
| Most misfires occur in only 1 or 2 cylinders | A |
| 3 cylinders or more have equal misfire counts | B |
|
| ||||
| A | |
| 5.INSPECT SPARK PLUG |
Inspect the spark plug of the misfiring cylinder .
|
| ||||
| OK | |
| 6.CHECK FOR SPARK (SPARK TEST) |
Perform spark test (Click here).
| NEXT | |
| 7.CHECK CYLINDER COMPRESSION PRESSURE |
Measure the cylinder compression pressure of the misfiring cylinder .
|
| ||||
| OK | |
| 8.CHECK ECM TERMINAL VOLTAGE (#10, #20, #30 AND/OR #40) |
![]() |
Disconnect the ECM connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D28-85 (#10) - D28-109 (E01) | Power switch on (IG) | 11 to 14 V |
| D28-84 (#20) - D28-109 (E01) | Power switch on (IG) | 11 to 14 V |
| D28-83 (#30) - D28-109 (E01) | Power switch on (IG) | 11 to 14 V |
| D28-82 (#40) - D28-109 (E01) | Power switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector (to ECM) |
Reconnect the ECM connector.
|
| ||||
| OK | |
| 9.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER |
Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).
|
| ||||
| OK | |
| 10.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks (Click here).
|
| ||||
| OK | |
| 11.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 12.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
Read the Coolant Temp twice, when the engine is both cold and warmed up.
| Tester Display | Condition | Specified Condition |
| Coolant Temp | Cold engine | Same as ambient air temperature |
| Warm engine | Between 75 and 100°C (167 and 212°F) |
|
| ||||
| OK | |
| 13.READ VALUE USING INTELLIGENT TESTER (MAF) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF, Coolant Temp and Engine Speed.
Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.
Read MAF with the engine speed at 2500 rpm.
| Tester Display | Condition | Specified Condition |
| MAF | Park (P) has been selected A/C: off Engine Speed: 2500 rpm | Between 4.5 gm/sec. and 8.5 gm/sec. |
|
| ||||
| OK | |
| 14.ADJUST VALVE TIMING |
![]() |
| *1 | Top |
| *2 | Alignment Mark |
| *3 | No. 1 Cylinder at TDC Compression |
| NEXT | |
| 15.CHECK WHETHER DTC OUTPUT RECURS (DTC P0300, P0301, P0302, P0303 OR P0304) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the power switch off and wait for 30 seconds.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P0300, P0301, P0302, P0303 or P0304 is output) | B |
|
| ||||
| A | ||
| ||
| 16.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks (Click here).
|
| ||||
| OK | |
| 17.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 18.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
Read the Coolant Temp twice, when the engine is both cold and warmed up.
| Tester Display | Condition | Specified Condition |
| Coolant Temp | Cold engine | Same as ambient air temperature |
| Warm engine | Between 75 and 100°C (167 and 212°F) |
|
| ||||
| OK | |
| 19.READ VALUE USING INTELLIGENT TESTER (MAF) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF, Coolant Temp and Engine Speed.
Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.
Read MAF with the engine speed at 2500 rpm.
| Tester Display | Condition | Specified Condition |
| MAF | Park (P) has been selected A/C: off Engine Speed: 2500 rpm | Between 4.5 gm/sec. and 8.5 gm/sec. |
|
| ||||
| OK | |
| 20.INSPECT SPARK PLUG |
Inspect the spark plug of the misfiring cylinder .
|
| ||||
| OK | |
| 21.CHECK FOR SPARK (SPARK TEST) |
Perform spark test (Click here).
| NEXT | |
| 22.CHECK CYLINDER COMPRESSION PRESSURE |
Measure the cylinder compression pressure of the misfiring cylinder .
|
| ||||
| OK | |
| 23.CHECK ECM TERMINAL VOLTAGE (#10, #20, #30 AND/OR #40) |
![]() |
Disconnect the ECM connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D28-85 (#10) - D28-109 (E01) | Power switch on (IG) | 11 to 14 V |
| D28-84 (#20) - D28-109 (E01) | Power switch on (IG) | 11 to 14 V |
| D28-83 (#30) - D28-109 (E01) | Power switch on (IG) | 11 to 14 V |
| D28-82 (#40) - D28-109 (E01) | Power switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector (to ECM) |
Reconnect the ECM connector.
|
| ||||
| OK | |
| 24.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER |
Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).
|
| ||||
| OK | |
| 25.ADJUST VALVE TIMING |
![]() |
| *1 | Top |
| *2 | Alignment Mark |
| *3 | No. 1 Cylinder at TDC Compression |
| NEXT | |
| 26.CHECK WHETHER DTC OUTPUT RECURS (DTC P0300, P0301, P0302, P0303 OR P0304) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the power switch off and wait for 30 seconds.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0300, P0301, P0302, P0303 or P0304
Check the DTC judgment result.
| Result | Proceed to |
| ABNORMAL (DTC P0300, P0301, P0302, P0303 or P0304 is output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | |
| 27.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION) |
Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM (Click here).
| NEXT | |
| 28.CHECK WHETHER DTC OUTPUT RECURS (DTC P0300, P0301, P0302, P0303 OR P0304) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the power switch off and wait for 30 seconds.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
| ABNORMAL (DTC P0300, P0301, P0302, P0303 or P0304 is output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | |
| 29.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM) |
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D5-5 (VG) - D28-94 (VG) | Always | Below 1 Ω |
| D5-4 (E2G) - D28-117 (E2G) |
| Tester Connection | Condition | Specified Condition |
| D5-5 (VG) or D28-94 (VG) - Body ground | Always | 10 kΩ or higher |
Reconnect the mass air flow meter sub-assembly connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 30.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY |
Replace the mass air flow meter sub-assembly (Click here).
| NEXT | |
| 31.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the power switch off and wait for 30 seconds.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P0300, P0301, P0302, P0303 or P0304 is output) | B |
|
| ||||
| A | ||
| ||
| 32.CHECK FUEL LINE |
Check the fuel lines for leaks or blockage.
|
| ||||
| OK | ||
| ||