AUDIO AND VISUAL SYSTEM > Radio Broadcast cannot be Received or Poor Reception |
| 1.CHECK RADIO RECEIVER ASSEMBLY |
Check the radio automatic station search function.
Check the radio automatic station search function by activating it.
| Result | Proceed to |
| Automatic station search function stops on a station | A |
| Automatic station search function does not stop | B |
|
| ||||
| A | ||
| ||
| 2.CHECK OPTIONAL COMPONENTS |
Check optional components (sunshade film, telephone antenna, etc.).
Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.
| Result | Proceed to |
| Optional components are installed | A |
| Optional components are not installed | B |
|
| ||||
| A | ||
| ||
| 3.CHECK RADIO ANTENNA |
Preparation for check
Remove the roof antenna pole sub-assembly from the amplifier antenna assembly.
Check for noise
Turn the power switch on (ACC) with the radio receiver assembly connector connected.
Turn the radio on and tune into AM mode.
Place a screwdriver, thin wire, or other metal object on the amplifier antenna threaded installation portion for the roof antenna pole sub-assembly and check that noise can be heard from the speakers.
| Result | Proceed to |
| Noise does not occur | A |
| Noise occurs | B |
|
| ||||
| A | |
| 4.CONFIRM MODEL |
Check the type of connection between the antenna cord and radio receiver assembly.
| Result | Proceed to |
| for Plug Type Antenna Cord | A |
| for Connector Type Antenna Cord | B |
|
| ||||
| A | |
| 5.CHECK RADIO RECEIVER ASSEMBLY |
![]() |
Preparation for check
Remove the antenna plug from the radio receiver assembly.
Check for noise
Turn the power switch on (ACC) with the radio receiver assembly connector connected.
Turn the radio on and tune into AM mode.
Place a screwdriver, thin wire or other metal object on the radio receiver assembly antenna jack and check that noise can be heard from the speakers.
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - AMPLIFIER ANTENNA ASSEMBLY) |
![]() |
Disconnect the radio receiver assembly and amplifier antenna assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L34-8 (ANT) - L36-2 (B) | Always | Below 1 Ω |
| L34-8 (ANT) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Radio Receiver Assembly) |
| *2 | Front view of wire harness connector (to Amplifier Antenna Assembly) |
|
| ||||
| OK | |
| 7.INSPECT RADIO RECEIVER ASSEMBLY |
![]() |
Reconnect the radio receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L36-2 (B) - Body ground | Power switch on (IG) Radio switch on | 8 V or higher |
| *1 | Front view of wire harness connector (to Amplifier Antenna Assembly) |
|
| ||||
| OK | |
| 8.CHECK ANTENNA CORD |
Remove the antenna plug of the radio receiver assembly and antenna.
Measure the resistance between the antenna and radio receiver assembly to check for an open circuit in the antenna cord.
Measure the resistance between the antenna cord and body ground to check for a short circuit in the antenna cord.
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | ||
| ||
| 9.CHECK RADIO RECEIVER ASSEMBLY |
![]() |
Preparation for check
Remove the antenna connector from the radio receiver assembly.
Check for noise
Turn the power switch on (ACC) with the radio receiver assembly connector connected.
Turn the radio on and tune into AM mode.
Place a screwdriver, thin wire or other metal object on the radio receiver assembly antenna jack and check that noise can be heard from the speakers.
|
| ||||
| OK | |
| 10.INSPECT RADIO RECEIVER ASSEMBLY |
![]() |
Disconnect the radio receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| RA-5 (ANT+) - Body ground | Power switch on (ACC) Radio switch on | 8 V or higher |
| *1 | Component without harness connected (Radio Receiver Assembly) |
|
| ||||
| OK | |
| 11.CHECK ANTENNA CORD |
Remove the antenna connector of the radio receiver assembly and antenna.
Measure the resistance between the antenna and radio receiver assembly to check for an open circuit in the antenna cord.
Measure the resistance between the antenna cord and body ground to check for a short circuit in the antenna cord.
|
| ||||
| OK | |
| 12.REPLACE AMPLIFIER ANTENNA ASSEMBLY |
Replace the amplifier antenna assembly and check if radio broadcasts can be received normally (Click here).
|
| ||||
| OK | ||
| ||