Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Headup Display Malfunction

for Preparation Click here


DESCRIPTION

This circuit is the power source circuit for the headup display (combination meter mirror ECU). This circuit provides two types of power sources; one is a constant power source, and the other is a IG power source.

WIRING DIAGRAM


E188177E04


INSPECTION PROCEDURE

HINT:
Before starting the following inspection, confirm the headup display (combination meter mirror ECU) position and illuminance, then perform the on-vehicle inspection (Click here).

1.SYSTEM CHECK
  1. Check the symptom of the headup display (combination meter mirror ECU).

    Result:
    Result
    Proceed to
    Headup display (combination meter mirror ECU) does not operate at all.
    A
    Cruise information display does not change.
    B



B
Go to step 3
A


2.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY CIRCUIT)


    E159387E32
  1. Disconnect the L111 connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L111-13 (12V) - Body ground
    Power switch on (IG)
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L111-16 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Headup Display (Combination Meter Mirror ECU))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HEADUP DISPLAY (COMBINATION METER MIRROR ECU) (Click here)  

3.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester ON.

  1. Enter the following menus: Body / Combination Meter / Data List.

  1. Check the values by referring to the table below.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Head Up Display Switch (Up)
    Headup display position up switch condition
    OFF: Headup display position up switch not pressed
    -
    ON: Headup display position up switch pressed
    -
    Head Up Display Switch (Down)
    Headup display position down switch condition
    OFF: Headup display position down switch not pressed
    -
    ON: Headup display position down switch pressed
    -
    Head Up Display Switch (Main)
    Headup display main switch condition
    OFF: Headup display main switch not pressed
    -
    ON: Headup display main switch pressed
    -

    OK:
    Each switch condition displayed on the intelligent tester changes with the actual switch operation.



B
Go to step 4
A

REPLACE COMBINATION METER ASSEMBLY (NO. 3 METER CIRCUIT PLATE) (Click here)  

4.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY - NO. 3 METER CIRCUIT PLATE)
  1. Disconnect the L111 and L57 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance :
    Tester Connection
    Condition
    Specified Condition
    L111-17 (BKR) - L106-5 (BKR)
    Always
    Below 1 Ω
    L111-17 (BKR) - Body ground
    Always
    10 kΩ or higher
    L111-18 (LAT) - L106-6 (LAT)
    Always
    Below 1 Ω
    L111-18 (LAT) - Body ground
    Always
    10 kΩ or higher
    L111-19 (CLKH) - L106-7 (CLKH)
    Always
    Below 1 Ω
    L111-19 (CLKH) - Body ground
    Always
    10 kΩ or higher
    L111-20 (CLKL) - L106-8 (CLKL)
    Always
    Below 1 Ω
    L111-20 (CLKL) - Body ground
    Always
    10 kΩ or higher
    L111-21 (SIH) - L106-9 (SIH)
    Always
    Below 1 Ω
    L111-21 (SIH) - Body ground
    Always
    10 kΩ or higher
    L111-22 (SIL) - L106-10 (SIL)
    Always
    Below 1 Ω
    L111-22 (SIL) - Body ground
    Always
    10 kΩ or higher
    L111-23 (WE) - L106-11 (WE)
    Always
    Below 1 Ω
    L111-23 (WE) - Body ground
    Always
    10 kΩ or higher
    L111-2 (STP1) - L106-14 (STP1)
    Always
    Below 1 Ω
    L111-2 (STP1) - Body ground
    Always
    10 kΩ or higher
    L111-3 (STP2) - L106-15 (STP2)
    Always
    Below 1 Ω
    L111-3 (STP2) - Body ground
    Always
    10 kΩ or higher
    L111-4 (STP3) - L106-16 (STP3)
    Always
    Below 1 Ω
    L111-4 (STP3) - Body ground
    Always
    10 kΩ or higher
    L111-5 (STP4) - L106-17 (STP4)
    Always
    Below 1 Ω
    L111-5 (STP4) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT TRIP SWITCH


    E192285E02
  1. Disconnect the L57 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (CH) - 12 (E)
    HUD/MODE switch pressed
    Below 1 Ω
    2 (CH) - 12 (E)
    Always
    10 kΩ or higher
    12 (E) - 14 (HDD)
    Down switch pressed
    Below 1 Ω
    12 (E) - 14 (HDD)
    Always
    10 kΩ or higher
    12 (E) - 15 (HDU)
    Up switch pressed
    Below 1 Ω
    12 (E) - 15 (HDU)
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (Trip Switch)



NG
CHECK AND REPLACE TRIP SWITCH (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (TRIP SWITCH - NO. 3 METER CIRCUIT PLATE)
  1. Disconnect the L27, L57, and L107 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance :
    Tester Connection
    Condition
    Specified Condition
    L57-1 (CS) - L27-2 (TC O)
    Always
    Below 1 Ω
    L57-1 (CS) - Body ground
    Always
    10 kΩ or higher
    L57-9 (HOUR) - L27-12 (HOUR)
    Always
    Below 1 Ω
    L57-9 (HOUR) - Body ground
    Always
    10 kΩ or higher
    L57-10 (MIN) - L27-13 (MIN)
    Always
    Below 1 Ω
    L57-10 (HOUR) - Body ground
    Always
    10 kΩ or higher
    L57-11 (RST) - L27-17 (RST)
    Always
    Below 1 Ω
    L57-11 (RST) - Body ground
    Always
    10 kΩ or higher
    L57-12 (E) - L107-2 (E)
    Always
    Below 1 Ω
    L57-12 (E) - Body ground
    Always
    10 kΩ or higher
    L57-15 (HDU) - L107-7 (HDS)
    Always
    Below 1 Ω
    L57-15 (HDU) - Body ground
    Always
    10 kΩ or higher
    L57-14 (HDD) - L107-4 (HUDD)
    Always
    Below 1 Ω
    L57-14 (HDD) - Body ground
    Always
    10 kΩ or higher
    L57-3 (TAIL) - L107-3 (HUDI)
    Always
    Below 1 Ω
    L57-3 (TAIL) - Body ground
    Always
    10 kΩ or higher
    L57-2 (CH) - L107-8 (HUDO)
    Always
    Below 1 Ω
    L57-2 (CH) - Body ground
    Always
    10 kΩ or higher
    L57-6 (NVI) - L107-9 (IIND)
    Always
    Below 1 Ω
    L57-6 (NVI) - Body ground
    Always
    10 kΩ or higher
    L57-7 (NVM) - L107-1 (NVSW)
    Always
    Below 1 Ω
    L57-7 (NVM) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.REPLACE HEADUP DISPLAY (COMBINATION METER MIRROR ECU)
  1. Replace the headup display (combination meter mirror ECU) with a new or a known good one (Click here).

    OK:
    The operation of the headup display (combination meter mirror ECU) returns to normal.



NG
REPLACE COMBINATION METER ASSEMBLY (NO. 3 METER CIRCUIT PLATE) (Click here)
OK

END