Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTELLIGENT PARKING ASSIST SYSTEM

INTELLIGENT PARKING ASSIST SYSTEM > "CHK" message(s) are displayed on the SIGNAL CHECK screen.

for Preparation Click here


DESCRIPTION

On the SIGNAL CHECK screen, it is possible to check if the state of signals sent to the parking assist ECU is normal (Click here).

HINT:
  1. On the SIGNAL CHECK screen, "OK" (blue) is displayed for items with a normal inspection result or input state.
  2. On the SIGNAL CHECK screen, "CHK" (red) is displayed for items with an abnormal inspection result or input state.
  3. Displayed items may differ depending on vehicle specifications.


Item
Signal Input Method
Detail
DTC Output when Abnormal Result is Displayed
Signal Receiver
CAN
CAN communication
CAN communication condition
DTC is output
-
IPA SW
Vehicle wire harness
Parking assist pre support switch signal input
DTC is not output
Parking assist pre support switch
BCTY
CAN communication
CAN communication condition with main body ECU (multiplex network body ECU)
DTC is output
Main body ECU (multiplex network body ECU)
EPS TYPE
-
Brush information for EPS currently selected at individual setting screen
DTC is not output
-
HT SENS
Vehicle wire harness
Height control sensor signal input
DTC is output
Rear height control sensor sub-assembly RH
HT INIT
-
Height control sensor vehicle height difference setting status
DTC is output
-
STR
CAN communication
Steering angle sensor signal input
DTC is output
Spiral with sensor cable sub-assembly
HANDLE
CAN communication
Steering position signal input
DTC is output
Main body ECU (multiplex network body ECU)

WIRING DIAGRAM


E188891E01


INSPECTION PROCEDURE

NOTICE:
  1. When "System initializing" message is displayed on the navigation receiver assembly after the battery terminal disconnected, correct the steering angle neutral point (Click here).
  2. Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the intelligent parking assist system may be needed (Click here).

1.CHECK DISPLAY CHECK MODE


    E188837
  1. Check which items display "CHK" (red) on the SIGNAL CHECK screen.

    Result:
    Result
    Proceed to
    "IPA SW" displays "CHK" (red).
    A
    "HT INIT" displays "CHK" (red).
    B
    Both "HT SENS" and "HT INIT" display "CHK" (red).
    C
    Any of "CAN", "BCTY", "STR" and "HANDLE" displays "CHK" (red).
    C



B
ADJUST HEIGHT CONTROL SENSOR VEHICLE HEIGHT DIFFERENCE SETTING (Click here)

C
CHECK DTC OUTPUT (Click here)
A


2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - PARKING ASSIST PRE SUPPORT SWITCH)
  1. Disconnect the L65 connector from the parking assist ECU.

  1. Disconnect the L56 connector from the parking assist pre support switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L65-11 (ISSW) - L56-6 (IG)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT PARKING ASSIST PRE SUPPORT SWITCH
  1. Remove the parking assist pre support switch (Click here).



    E159999E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (E) - 6 (IG)
    Parking assist pre support switch pushed in
    Below 1 Ω
    Parking assist pre support switch not pushed
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (Parking Assist Pre Support Switch)



NG
REPLACE PARKING ASSIST PRE SUPPORT SWITCH (Click here)
OK

REPLACE PARKING ASSIST ECU (Click here)