Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM

DTC    P0505    Idle Control System Malfunction

for Preparation Click here


DESCRIPTION

The idle speed is controlled by the electronic throttle control system. The electronic throttle control system is comprised of: 1) the one valve type throttle body assembly; 2) a throttle actuator, which operates the throttle valve; 3) a throttle position sensor, which detects the opening angle of the throttle valve; 4) an accelerator pedal position sensor, which detects the accelerator pedal position; and 5) the ECM, which controls the electronic throttle control system. Based on the target idle speed, the ECM controls the throttle actuator to provide the proper throttle valve opening angle.

DTC No.
DTC Detection Condition
Trouble Area
P0505
Idling speed continues to vary greatly from target idling speed (2 trip detection logic)
  1. Electronic throttle control system
  2. Intake system
  3. PCV hose connections
  4. EGR valve assembly
  5. ECM

MONITOR DESCRIPTION

The ECM monitors the idling speed and idling air flow volume to conduct idle speed control. The ECM determines that the idle speed control system is malfunctioning if either of the following conditions is met:
  1. The difference between the target engine idling speed and actual engine idling speed exceeds the threshold and the IAC flow rate learned value is stuck at the upper or lower limit for 5 seconds or more.
  2. After driving at a vehicle speed of 6.25 mph (10 km/h) or more, the difference between the target and actual engine idling speed exceeds the threshold 5 times or more during a driving cycle, and then the system determines that the idle speed control flow rate learned value is stuck at the upper or lower limit, or that the IAC flow rate learned value has been changed by an amount that exceeds the threshold.

A121611E20


MONITOR STRATEGY


Related DTCs
P0505: Idle speed control function
Required Sensors/Components (Main)
Electronic throttle control system
Required Sensors/Components (Related)
Crankshaft position sensor
Engine coolant temperature sensor
Vehicle speed sensor
Frequency of Operation
Once per driving cycle
Duration
5 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
P0010 (Camshaft timing oil control valve assembly bank 1)
P0011 (VVT system bank 1 - advance)
P0012 (VVT system bank 1 - retard)
P0016 (VVT system bank 1 - misalignment)
P0031, P0032, P101D (Air fuel ratio sensor heater - sensor 1)
P0102, P0103 (Mass air flow meter)
P0107, P0108 (Manifold absolute pressure)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P014C, P014D (Air fuel ratio sensor - slow response)
P015A, P015B (Air fuel ratio sensor - delayed response)
P0171, P0172 (Fuel system)
P0301, P0302, P0303, P0304 (Misfire)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343 (Camshaft position sensor)
P0351, P0352, P0353, P0354 (Igniter)
P0401 (EGR system (closed))
P0451, P0452, P0453 (EVAP system)
P2195, P2196 (Air fuel ratio sensor - rationality)
P219A, P219C, P219D, P219E, P219F (Air fuel ratio sensor - imbalance)
P2237 (Air fuel ratio sensor - open)
P2238, P2252 (Air fuel ratio sensor - low impedance)
P2239, P2253 (Air fuel ratio sensor - high impedance)
Engine
Running

TYPICAL MALFUNCTION THRESHOLDS


Either of the following condition is met
1 or 2
1. Both of the following conditions A and B are met
-
A. Engine speed - Target engine speed
Less than -100 rpm, or more than 150 rpm
B. IAC flow rate learned value
0.5 L/sec. or less, or 6.1 L/sec. or more for 5 seconds or more
2. Both of the following conditions C and D are met
-
C. Frequency that both of the following conditions (a) and (b) are met
5 times or more
(a) Engine speed - Target engine speed
Less than -100 rpm, or more than 150 rpm
(b) Vehicle condition
Stopped after being driven at 6.25 mph (10 km/h) or more
D. Either of the following condition is met
(c) or (d)
(c) Amount of change IAC flow rate learning value
+1.837 L/sec. or more, or -3.08 L/sec. or less
(d) IAC flow rate learning value
0.5 L/sec. or less, or 6.1 L/sec. or more

CONFIRMATION DRIVING PATTERN


A299577E03

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the power switch off and wait for at least 30 seconds.
  5. Turn the power switch on (IG) and turn the Techstream on [A].
  6. Put the engine in inspection mode (maintenance mode) (Click here).
  7. Start the engine and idle the vehicle until the coolant temperature reaches 70°C (158°F) or higher with all the accessories switch off [B].
  8. Turn the power switch off and wait for at least 30 seconds.
  9. Disconnect the cable from the negative (-) auxiliary battery terminal.
  10. Reconnect the cable to the negative (-) auxiliary battery terminal.
  11. Turn the power switch on (IG) and turn the Techstream on.
  12. Put the engine in inspection mode (maintenance mode) (Click here).
  13. Start the engine and rev the engine for 5 seconds with Park (P) selected [C].
  14. Idle the engine for 5 minutes or more [D].

    HINT:
    In order to keep the idling stable, turn off the A/C and all other electric loads and do not perform any shift operations.

  15. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
  16. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  17. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  18. Input the DTC: P0505.
  19. Check the DTC judgment result.

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [F] through [I].

  20. Accelerate the vehicle to 10 km/h (6.25 mph) or more [F].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  21. Stop the vehicle and rev the engine for 5 seconds with Park (P) selected [G].
  22. Idle the engine for 20 seconds or more [H].
  23. Repeat the steps [F] through [H] 10 times.
  24. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [I].
  25. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  26. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  27. Input the DTC: P0505.
  28. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  29. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If a permanent DTC is not output, the system is normal.


INSPECTION PROCEDURE

HINT:
  1. The following conditions may also cause DTC P0505 to be stored:
    1. The floor carpet overlapping slightly onto the accelerator pedal, causing the accelerator pedal to be slightly depressed and therefore the throttle valve position to be slightly open.
    2. The accelerator pedal being not fully released.
  2. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
  3. Refer to "Data List / Active Test" [Engine Speed and ISC Learning Value] (Click here).

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0505)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC P0505 is output
    A
    DTC P0505 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0505 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK PCV HOSE CONNECTIONS
  1. Check the PCV hose connections.

    OK:
    PCV valve and hose are connected correctly and are not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


3.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks (Click here).

    OK:
    No leaks from the intake system.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the intake system (Click here).



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or more.

    HINT:
    The A/C switch and all accessory switches should be off.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Throttle Idle Position and MAP.

  1. Check that the Throttle Idle Position in ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.

    HINT:
    1. Do not leave the EGR valve open for 10 seconds or more during the Active Test.
    2. Be sure to return the EGR valve to step 0 when the Active Test is completed.
    3. Do not open the EGR valve 30 steps or more during the Active Test.

    OK:
    MAP and idling condition change in response to EGR step position when Throttle Idle Position is ON in Data List.


    Standard:

    -
    EGR Step Position (Active Test)
    0 Steps
    0 to 30 Steps
    Idling condition
    (Throttle Idle Position: ON)
    Steady idling
    Idling changes from steady to rough idling or engine stalls
    MAP
    (Data List)
    MAP value is 20 to 40 kPa (150 to 300 mmHg)
    (EGR valve is fully closed)
    MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed

    HINT:
    During Active Test, if the idling condition does not change in response to EGR step position, then there is probably a malfunction in the EGR valve.



OK
Go to step 6

NG
Go to step 5

5.INSPECT EGR VALVE ASSEMBLY
  1. Remove the EGR valve assembly (Click here).

  1. Check if the EGR valve is stuck open.

    OK:
    EGR valve is tightly closed.

    HINT:
    Perform "Inspection After Repair" after replacing the EGR valve assembly (Click here).



NG
REPLACE EGR VALVE ASSEMBLY (Click here)
OK


6.INSPECT THROTTLE BODY ASSEMBLY
  1. Check for contamination between the throttle valve and the housing and then check that the throttle valve moves smoothly.

    OK:
    Throttle valve is not contaminated with foreign objects and moves smoothly.

    HINT:
    Perform "Inspection After Repair" after replacing the throttle body assembly (Click here).



NG
REPLACE THROTTLE BODY ASSEMBLY (Click here)
OK


7.CONFIRM WHETHER DTC OUTPUT RECURS (DTC P0505)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Clear the DTC (Click here).

  1. Turn the power switch off and wait for at least 30 seconds.

  1. Turn the power switch on (IG) and turn the Techstream on.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

  1. Read the pending DTCs.

    Result:

    Result
    Proceed to
    DTC P0505 is output
    A
    DTC is not output
    B



B
END
A

REPLACE ECM (Click here)