DTC B1780 Front Occupant Classification Sensor LH Circuit Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1780 |
|
|

| 1.CHECK CONNECTORS |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Check that the connectors are properly connected to the occupant classification ECU and front occupant classification sensor LH.
Disconnect the connectors from the occupant classification ECU and front occupant classification sensor LH.
Check that the terminals of connectors are not damaged.
|
| ||||
| OK | |
| 2.CHECK FRONT SEAT WIRE RH (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| W2-1 (SGD1) - Body ground | Power switch on (IG) | Below 1 V |
| W2-7 (SIG1) - Body ground | Power switch on (IG) | Below 1 V |
| W2-11 (SVC1) - Body ground | Power switch on (IG) | Below 1 V |
| *1 | Front Occupant Classification Sensor LH |
| *2 | Occupant Classification ECU |
| *3 | Front Seat Wire RH |
| *4 | Front view of wire harness connector (to Occupant Classification ECU) |
| *5 | Connector B |
|
| ||||
| OK | |
| 3.CHECK FRONT SEAT WIRE RH (OPEN) |
Turn the power switch off.

Disconnect the cable from the negative (-) auxiliary battery terminal.
Using SST, connect terminals 1 (SVC1) and 3 (SGD1), and connect terminals 2 (SIG1) and 3 (SGD1) of connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| W2-7 (SIG1) - W2-1 (SGD1) | Always | Below 1 Ω |
| W2-11 (SVC1) - W2-1 (SGD1) | Always | Below 1 Ω |
| *1 | Front Occupant Classification Sensor LH | *2 | Occupant Classification ECU |
| *3 | Front Seat Wire RH | *4 | Front view of wire harness connector (to Occupant Classification ECU) |
| *5 | Front view of wire harness connector (to Front Occupant Classification Sensor LH) | *6 | Connector B |
| *7 | Connector C | - | - |
|
| ||||
| OK | |
| 4.CHECK FRONT SEAT WIRE RH (SHORT) |
![]() |
Disconnect SST from connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| W2-7 (SIG1) - W2-1 (SGD1) | Always | 1 MΩ or higher |
| W2-11 (SVC1) - W2-1 (SGD1) | Always | 1 MΩ or higher |
| W2-7 (SIG1) - W2-11 (SVC1) | Always | 1 MΩ or higher |
| *1 | Front Occupant Classification Sensor LH |
| *2 | Occupant Classification ECU |
| *3 | Front Seat Wire RH |
| *4 | Front view of wire harness connector (to Occupant Classification ECU) |
| *5 | Connector B |
|
| ||||
| OK | |
| 5.CHECK FRONT SEAT WIRE RH (SHORT TO GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| W2-1 (SGD1) - Body ground | Always | 1 MΩ or higher |
| W2-7 (SIG1) - Body ground | Always | 1 MΩ or higher |
| W2-11 (SVC1) - Body ground | Always | 1 MΩ or higher |
| *1 | Front Occupant Classification Sensor LH |
| *2 | Occupant Classification ECU |
| *3 | Front Seat Wire RH |
| *4 | Front view of wire harness connector (to Occupant Classification ECU) |
| *5 | Connector B |
|
| ||||
| OK | |
| 6.CHECK DTC |
Connect the connectors to the occupant classification ECU and front occupant classification sensor LH.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Clear the DTCs stored in the occupant classification ECU (Click here).
Clear the DTCs stored in the center airbag sensor assembly (Click here).
Turn the power switch off.
Turn the power switch on (IG).
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 7.REPLACE OCCUPANT CLASSIFICATION ECU |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Replace the occupant classification ECU (Click here).
| NEXT | |
| 8.CHECK DTC |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Clear the DTCs stored in the occupant classification ECU (Click here).
Clear the DTCs stored in the center airbag sensor assembly (Click here).
Turn the power switch off.
Turn the power switch on (IG).
Check for DTCs (Click here).
|
| ||||
| OK | |
| 9.PERFORM ZERO POINT CALIBRATION |
Connect the cable to the negative (-) auxiliary battery terminal.
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Using the Techstream, perform Zero Point Calibration (Click here).
| NEXT | |
| 10.PERFORM SENSITIVITY CHECK |
Using the Techstream, perform Sensitivity Check (Click here).
| NEXT | ||
| ||
| 11.REPLACE FRONT SEAT CUSHION SPRING ASSEMBLY RH |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Replace the front seat cushion spring assembly RH (Click here).
| NEXT | |
| 12.PERFORM ZERO POINT CALIBRATION |
Connect the cable to the negative (-) auxiliary battery terminal.
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Using the Techstream, perform Zero Point Calibration (Click here).
| NEXT | |
| 13.PERFORM SENSITIVITY CHECK |
Using the Techstream, perform Sensitivity Check (Click here).
| NEXT | ||
| ||