Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM

DTC    B1781    Front Occupant Classification Sensor RH Circuit Malfunction

for Preparation Click here


DESCRIPTION

The front occupant classification sensor RH circuit consists of the occupant classification ECU and front occupant classification sensor RH.
DTC B1781 is stored when a malfunction is detected in the front occupant classification sensor RH circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1781
  1. The occupant classification ECU receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front occupant classification sensor RH circuit.
  2. Front occupant classification sensor RH malfunction
  3. Occupant classification ECU malfunction
  1. Front seat wire RH
  2. Front seat cushion spring assembly RH (Front occupant classification sensor RH)
  3. Occupant classification ECU

HINT:
When DTC B1650/32 is detected as a result of troubleshooting for the airbag system, check the DTCs stored in the occupant classification ECU. When DTC B1781 is output, perform troubleshooting for the DTC.


WIRING DIAGRAM


C170432E22


INSPECTION PROCEDURE

HINT:
  1. If troubleshooting (wire harness inspection) is difficult to perform, remove the front passenger seat installation bolts to see under the seat cushion.
  2. In the above case, hold the seat so that it does not fall down. Hold the seat only as necessary because holding the seat for a long period of time may cause seat rail deformation.

1.CHECK CONNECTORS
  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Check that the connectors are properly connected to the occupant classification ECU and front occupant classification sensor RH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the occupant classification ECU and front occupant classification sensor RH.

  1. Check that the terminals of connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE FRONT SEAT WIRE RH
OK


2.CHECK FRONT SEAT WIRE RH (SHORT TO B+)


    C169171E30
  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    W2-2 (SGD2) - Body ground
    Power switch on (IG)
    Below 1 V
    W2-8 (SIG2) - Body ground
    Power switch on (IG)
    Below 1 V
    W2-12 (SVC2) - Body ground
    Power switch on (IG)
    Below 1 V

    Text in Illustration 
    *1
    Front Occupant Classification Sensor RH
    *2
    Occupant Classification ECU
    *3
    Front Seat Wire RH
    *4
    Front view of wire harness connector
    (to Occupant Classification ECU)
    *5
    Connector B



NG
REPLACE FRONT SEAT WIRE RH
OK


3.CHECK FRONT SEAT WIRE RH (OPEN)


  1. Turn the power switch off.


    C169172E31

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Using SST, connect terminals 1 (SVC2) and 3 (SGD2), and connect terminals 2 (SIG2) and 3 (SGD2) of connector C.

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W2-8 (SIG2) - W2-2 (SGD2)
    Always
    Below 1 Ω
    W2-12 (SVC2) - W2-2 (SGD2)
    Always
    Below 1 Ω


    Text in Illustration 
    *1
    Front Occupant Classification Sensor RH
    *2
    Occupant Classification ECU
    *3
    Front Seat Wire RH
    *4
    Front view of wire harness connector
    (to Occupant Classification ECU)
    *5
    Front view of wire harness connector
    (to Front Occupant Classification Sensor RH)
    *6
    Connector B
    *7
    Connector C
    -
    -



NG
REPLACE FRONT SEAT WIRE RH
OK


4.CHECK FRONT SEAT WIRE RH (SHORT)


    C169171E30
  1. Disconnect SST from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W2-8 (SIG2) - W2-2 (SGD2)
    Always
    1 MΩ or higher
    W2-12 (SVC2) - W2-2 (SGD2)
    Always
    1 MΩ or higher
    W2-8 (SIG2) - W2-12 (SVC2)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Front Occupant Classification Sensor RH
    *2
    Occupant Classification ECU
    *3
    Front Seat Wire RH
    *4
    Front view of wire harness connector
    (to Occupant Classification ECU)
    *5
    Connector B



NG
REPLACE FRONT SEAT WIRE RH
OK


5.CHECK FRONT SEAT WIRE RH (SHORT TO GROUND)


    C169171E30
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W2-2 (SGD2) - Body ground
    Always
    1 MΩ or higher
    W2-8 (SIG2) - Body ground
    Always
    1 MΩ or higher
    W2-12 (SVC2) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Front Occupant Classification Sensor RH
    *2
    Occupant Classification ECU
    *3
    Front Seat Wire RH
    *4
    Front view of wire harness connector
    (to Occupant Classification ECU)
    *5
    Connector B



NG
REPLACE FRONT SEAT WIRE RH
OK


6.CHECK DTC
  1. Connect the connectors to the occupant classification ECU and front occupant classification sensor RH.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).

  1. Clear the DTCs stored in the occupant classification ECU (Click here).

  1. Clear the DTCs stored in the center airbag sensor assembly (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG).

  1. Check for DTCs (Click here).

    OK:
    DTC B1781 is not output.

    HINT:
    Codes other than DTC B1781 may be output at this time, but they are not related to this check.



NG
Go to step 7
OK

USE SIMULATION METHOD TO CHECK (Click here)  

7.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Replace the occupant classification ECU (Click here).

    HINT:
    Perform the following inspection using known good parts from another vehicle if possible.


NEXT


8.CHECK DTC
  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).

  1. Clear the DTCs stored in the occupant classification ECU (Click here).

  1. Clear the DTCs stored in the center airbag sensor assembly (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG).

  1. Check for DTCs (Click here).

    OK:
    DTC B1781 is not output.

    HINT:
    Codes other than DTC B1781 may be output at this time, but they are not related to this check.



NG
Go to step 11
OK


9.PERFORM ZERO POINT CALIBRATION
  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Using the Techstream, perform Zero Point Calibration (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.


NEXT


10.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform Sensitivity Check (Click here).

    Standard:
    27 to 33 kg (59.5 to 72.8 lb)


NEXT

END 

11.REPLACE FRONT SEAT CUSHION SPRING ASSEMBLY RH
  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Replace the front seat cushion spring assembly RH (Click here).


NEXT


12.PERFORM ZERO POINT CALIBRATION
  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Using the Techstream, perform Zero Point Calibration (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.


NEXT


13.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform Sensitivity Check (Click here).

    Standard:
    27 to 33 kg (59.5 to 72.8 lb)


NEXT

END