Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM

DTC    C1A05    Stop Light Switch Circuit

DTC    C1A4B    Stop Light Relay Circuit

for Preparation Click here


DESCRIPTION

When the brake pedal is depressed, the stop light switch sends a signal to the driving support ECU. Upon receiving the signal, the driving support ECU cancels speed control by the dynamic radar cruise control system. Even if there is a malfunction in the stop light signal circuit while the cruise control is operating, normal driving is maintained due to the fail-safe function. Dynamic radar cruise control speed control operation is canceled when battery voltage is applied to terminal STP-.
When the brake pedal is released, voltage is applied to terminal ST1- of the driving support ECU through the IGN fuse and the stop light switch, and the driving support ECU operates the dynamic radar cruise control.
The brake booster with master cylinder (skid control ECU) receives a signal from the driving support ECU and operates the brake actuator. The brake booster with master cylinder (skid control ECU) operates the brake actuator and at the same time illuminates the stop lights by operating the stop light control relay.
The stop light switch assembly sends a brake pedal operation signal to the driving support ECU.
After receiving the signal, the ECM performs fail-safe control by canceling cruise control system control of vehicle speed.
The brake booster with master cylinder (skid control ECU) outputs a stop light operation signal to the stop light control relay. When the brake booster with master cylinder (skid control ECU) detects a malfunction in the circuit related to the stop light, it informs the driving support ECU assembly via CAN communication and stores DTC C1A4B.

DTC No.
DTC Detection Condition
Trouble Area
C1A05
Voltages of terminals ST1- and STP- of driving support ECU are both below 1 V for 1 second
  1. Stop light switch assembly
  2. Stop light switch circuit
  3. Driving support ECU
C1A4B
The vehicle is being driven at a speed of approximately 50 km/h (31 mph) or more and the cruise control switch (vehicle-to-vehicle distance control mode) is on.
When the brake booster with master cylinder assembly (skid control ECU) detects a malfunction in the stop light control relay circuit, it sends a malfunction signal to the driving support ECU assembly via CAN communication and the driving support ECU assembly stores this DTC.
  1. CAN communication system
  2. Electronically controlled brake system
  3. brake booster with master cylinder assembly (Skid control ECU )
  4. Stop light control relay circuit
  5. Stop light control relay
  6. Driving support ECU assembly

WIRING DIAGRAM


E240083E02


INSPECTION PROCEDURE

NOTICE:
  1. When this DTC is output, a malfunction in the electronically controlled brake system is suspected. Check if the electronically controlled brake system is functioning normally (Click here).
  2. When this DTC is output, a malfunction in the lighting system is suspected. Check if the lighting system is functioning normally (Click here).

HINT:
  1. This circuit uses CAN communication. Therefore, be sure to check that the CAN communication system is normal before performing inspection.
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK FOR DTCs
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.

  1. Check for DTCs.

    Result:
    Result
    Proceed to
    DTC C1A05 is output
    A
    DTC C1A4B is output
    B

  1. Turn the power switch off.



B
Go to step 15
A


2.CHECK STOP LIGHT OPERATION
  1. Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

    OK:
    Condition
    Illumination Condition
    Brake pedal depressed
    ON
    Brake pedal released
    OFF



NG
GO TO LIGHTING SYSTEM (Click here)
OK


3.READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH ASSEMBLY)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Radar Cruise / Data List.

  1. Check the Data List for proper functioning of the stop light switch.

    Radar Cruise 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW 1 (M CPU)
    Stop light switch (Main-CPU) signal / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Stop Light SW 1 (S CPU)
    Stop light switch (Sub-CPU) signal / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Stop Light SW 2 (M CPU)
    Stop light switch (Main-CPU) signal / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

    OK:
    Display changes according to brake pedal operation described in above table.



NG
Go to step 11
OK


4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SKID CONTROL ECU)
  1. Disconnect the stop light switch assembly connector.

  1. Disconnect the brake booster with master cylinder (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A67-2 (L) - A58-33 (STP)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A67-2 (L) or A58-33 (STP) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the stop light switch assembly connector.

  1. Reconnect the brake booster with master cylinder (skid control ECU) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SKID CONTROL ECU)
OK


5.CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY - SKID CONTROL ECU)
  1. Disconnect the stop light control relay assembly connector.

  1. Disconnect the brake booster with master cylinder (skid control ECU) connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A28-1 (OUT) - A58-6 (STP2)
    Always
    Below 1 Ω
    A28-5 (STP) - A58-33 (STP)
    Always
    Below 1 Ω
    A28-9 (ACC) - A58-3 (STP0)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A28-1 (OUT) or A58-6 (STP2) - Body ground
    Always
    10 kΩ or higher
    A28-5 (STP) or A58-33 (STP) - Body ground
    Always
    10 kΩ or higher
    A28-9 (ACC) or A58-3 (STP0) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the stop light control relay connector.

  1. Reconnect the brake booster with master cylinder (skid control ECU) connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT CONTROL RELAY - SKID CONTROL ECU)
OK


6.INSPECT STOP LIGHT CONTROL RELAY
  1. Inspect the stop light control relay (Click here).



NG
REPLACE STOP LIGHT CONTROL RELAY (Click here)
OK


7.REPLACE BRAKE BOOSTER WITH MASTER CYLINDER (SKID CONTROL ECU)
  1. Replace the brake booster with master cylinder (skid control ECU) (Click here).


NEXT


8.CHECK FOR DTCs (DTC C1A05)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Clear the DTCs (Click here).

  1. Perform the following to make sure that the DTC detection conditions are met.

    HINT:
    If the detection conditions are not met, the malfunction cannot be detected.

    1. Drive the vehicle at a speed of between approximately 50 km/h (30 mph) and 170 km/h (105 mph).

    2. Turn the cruise control system on using the cruise control switch (ON-OFF button).

    3. Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.

  1. Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.

  1. Check for DTCs.

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC C1A05 is output
    B



B
Go to step 9
A

END 

9.REPLACE POWER MANAGEMENT CONTROL ECU
  1. Replace the power management control ECU (Click here).


NEXT


10.CHECK FOR DTCs (DTC C1A05)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Clear the DTCs (Click here).

  1. Perform the following to make sure that the DTC detection conditions are met.

    HINT:
    If the detection conditions are not met, the malfunction cannot be detected.

    1. Drive the vehicle at a speed of between approximately 50 km/h (30 mph) and 170 km/h (105 mph).

    2. Turn the cruise control system on using the cruise control switch (ON-OFF button).

    3. Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.

  1. Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.

  1. Check for DTCs.

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC C1A05 is output
    B



B
REPLACE DRIVING SUPPORT ECU (Click here)
A

END 

11.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SOURCE)


    E233265E10
  1. Disconnect the stop light switch assembly connector.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A67-1 (B) - A67-3 (GND)
    Power switch off
    11 to 14 V
    A67-5 (B) - A67-3 (GND)
    Power switch on (IG)
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A67-3 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Switch Assembly)

  1. Reconnect the stop light switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH - IG2 RELAY)
OK


12.INSPECT STOP LIGHT SWITCH ASSEMBLY


    E233266E08
  1. Remove the stop light switch assembly (Click here).
    Text in Illustration 
    *a
    Component with harness connected
    (Stop Light Switch Assembly)

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A67-2 (L) - A67-3 (GND)
    Power switch off, Brake pedal not depressed
    Below 1 V
    A67-4 (L) - A67-3 (GND)
    11 to 14 V
    A67-2 (L) - A67-3 (GND)
    Power switch off, Brake pedal depressed
    11 to 14 V
    A67-4 (L) - A67-3 (GND)
    Below 1 V



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


13.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - DRIVING SUPPORT ECU)
  1. Disconnect the driving support ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A67-2 (L) - L60-27 (STP-)
    Always
    Below 1 Ω
    A67-4 (L) - L60-28 (ST1-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A67-2 (L) or L60-27 (STP-) - Body ground
    Always
    10 kΩ or higher
    A67-4 (L) or L60-28 (ST1-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the stop light switch assembly connector.

  1. Reconnect the driving support ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - DRIVING SUPPORT ECU)
OK


14.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A67-2 (L) - Body ground
    Always
    10 kΩ or higher
    A67-4 (L) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the stop light switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)
OK

REPLACE DRIVING SUPPORT ECU (Click here)  

15.CHECK FOR DTCs (ABS/VSC/TRAC)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.

  1. Check for DTCs.

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B

  1. Turn the power switch off.



B
GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM (Click here)
A


16.CHECK STOP LIGHT OPERATION
  1. Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

    OK:
    Condition
    Illumination Condition
    Brake pedal depressed
    ON
    Brake pedal released
    OFF



NG
GO TO LIGHTING SYSTEM (Click here)
OK


17.CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY POWER SOURCE)


    E183992E14
  1. Disconnect the stop light control relay connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A28-6 (+B) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Control Relay)

  1. Reconnect the stop light control relay connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT CONTROL RELAY - STOP FUSE)
OK


18.CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY - BODY GROUND)


    E183992E15
  1. Disconnect the stop light control relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A28-8 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Control Relay)

  1. Reconnect the stop light control relay connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT CONTROL RELAY - BODY GROUND)
OK


19.CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY - STOP LIGHT SWITCH ASSEMBLY)


    E183992E16
  1. Turn the power switch off.

  1. Disconnect the stop light control relay connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A28-5 (STP) - Body ground
    Stop light switch ON (Brake pedal depressed)
    11 to 14 V
    A28-5 (STP) - Body ground
    Stop light switch OFF (Brake pedal released)
    Below 2 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Control Relay)

  1. Reconnect the stop light control relay connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT CONTROL RELAY - STOP LIGHT SWITCH ASSEMBLY)
OK


20.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SKID CONTROL ECU)
  1. Turn the power switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the brake booster with master cylinder (skid control ECU) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A58-33 (STP) - Body ground
    Stop light switch ON (Brake pedal depressed)
    11 to 14 V
    A58-33 (STP) - Body ground
    Stop light switch OFF (Brake pedal released)
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)

  1. Reconnect the brake booster with master cylinder (skid control ECU) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SKID CONTROL ECU)
OK


21.PERFORM ACTIVE TEST USING TECHSTREAM (STOP LIGHT RELAY)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test.

  1. Select the Active Test on the Techstream.

    ABS/VSC/TRAC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Stop Light Relay
    Stop light control relay
    Relay ON/OFF
    Stop lights come on

  1. Select the Data List on the Techstream.

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light Relay Output
    Stop light control relay output / ON or OFF
    ON: Relay output on
    OFF: Relay output off
    -

  1. Check stop light control relay operation and stop light operation on the Data List while performing the Active Test.

    Result:

    Result
    Proceed to
    Data List content and stop light operation are abnormal or Data List content is normal but stop lights do not turn on or off.
    A
    Data List content and stop light operation are normal.
    B

  1. Turn the power switch off.



B
Go to step 23
A


22.CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY - SKID CONTROL ECU)
  1. Disconnect the stop light control relay connector.

  1. Disconnect the brake booster with master cylinder (skid control ECU) connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    A28-9 (ACC) - A58-3 (STP0)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    A28-9 (ACC) or A58-3 (STP0) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the stop light control relay connector.

  1. Reconnect the brake booster with master cylinder (skid control ECU) connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT CONTROL RELAY - SKID CONTROL ECU)
OK


23.CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY - SKID CONTROL ECU)
  1. Disconnect the stop light control relay connector.

  1. Disconnect the brake booster with master cylinder (skid control ECU) connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    A28-1 (OUT) - A58-6 (STP2)
    Always
    Below 1 Ω

  1. Reconnect the stop light control relay connector.

  1. Reconnect the brake booster with master cylinder (skid control ECU) connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT CONTROL RELAY - SKID CONTROL ECU)
OK


24.INSPECT STOP LIGHT CONTROL RELAY
  1. Inspect the stop light control relay (Click here).



NG
REPLACE STOP LIGHT CONTROL RELAY (Click here)
OK


25.CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY - SKID CONTROL ECU)
  1. Turn the power switch off.

  1. Disconnect the brake booster with master cylinder (skid control ECU) connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A58-6 (STP2) - Body ground
    Stop light switch ON (Brake pedal depressed)
    11 to 14 V
    A58-6 (STP2) - Body ground
    Stop light switch OFF (Brake pedal released)
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)

  1. Reconnect the brake booster with master cylinder (skid control ECU) connectors.



NG
REPLACE STOP LIGHT CONTROL RELAY (Click here)
OK


26.CHECK FOR DTCs (DTC C1A4B)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Clear the DTCs (Click here).

  1. Perform the following to make sure that the DTC detection conditions are met.

    HINT:
    If the detection conditions are not met, the malfunction cannot be detected.

    1. Drive the vehicle at a speed of 50 km/h (30 mph) and 170 km/h (105 mph).

    2. Turn the cruise control switch (ON-OFF button) on.

    3. Push the -/SET switch to activate the cruise control.

  1. Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.

  1. Read the DTC.

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC C104B is output
    B



B
REPLACE DRIVING SUPPORT ECU ASSEMBLY (Click here)
A

END