Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM

DTC    P050A    Cold Start Idle Air Control System Performance

for Preparation Click here


MONITOR DESCRIPTION

This monitor will run when the engine is started at an engine coolant temperature of -10 to 50°C (14 to 122°F). The DTC can be set after the engine idles for 13 seconds (2 trip detection logic).
The DTC is designed to monitor the idle air control at cold start. When the engine is started at an engine coolant temperature of lower than 50°C (122°F), the ECM measures the accumulated mass air flow at idle. If it does not reach the specified level within 10 seconds, the ECM interprets this as a malfunction. The MIL is illuminated and a DTC is set when the malfunction is detected in consecutive driving cycles (2 trip detection logic).
The electronic throttle control system controls the idle speed. The electronic throttle control system operates the throttle actuator to open and close the throttle valve, and adjusts the intake air amount to achieve the target idle speed.

NOTICE:
The idle speed control learned values are cleared by performing a learned value reset. Idle speed control learning needs to be performed before this DTC can be stored. To perform idle speed control learning, the engine must be warmed up by allowing it to idle for 5 minutes. For idle speed control learning to be successful, when the engine is started to warm it up, there must be at least 10 seconds of idling with the coolant temperature less than 50°C (122°F) before allowing it to continue running for the 5 minutes learning period.


A234891E08


DTC No.
DTC Detection Condition
Trouble Area
P050A
Insufficient mass air flow at cold start
(2 trip detection logic)
  1. Throttle body assembly
  2. Mass air flow meter sub-assembly
  3. PCV hose
  4. Air cleaner filter element sub-assembly
  5. Intake system
  6. VVT system
  7. EGR valve assembly
  8. Wire harness or connector
  9. ECM

MONITOR STRATEGY


Related DTCs
P050A: Cold start idle air speed control system
Required Sensors/Components (Main)
Throttle body assembly
Required Sensors/Components (Related)
Mass air flow meter sub-assembly
Engine coolant temperature sensor
Frequency of Operation
Once per driving cycle
Duration
10 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
P0010 (Camshaft timing oil control valve bank 1)
P0011 (VVT system bank 1- advance)
P0012 (VVT system bank 1- retard)
P0016 (VVT system bank 1 - misalignment)
P0102, P0103 (Mass air flow meter)
P0107, P0108 (Manifold absolute pressure)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P014C, P014D (Air fuel ratio sensor - slow response)
P015A, P015B (Air fuel ratio sensor - delayed response)
P0171, P0172 (Fuel system)
P0301, P0302, P0303, P0304 (Misfire)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343 (Camshaft position sensor)
P0351, P0352, P0353, P0354 (Igniter)
P0401 (EGR system (closed))
P2195, P2196 (Air fuel ratio sensor - rationality)
P219A, P219C, P219D, P219E, P219F (Air fuel ratio sensor - imbalance)
P2237 (Air fuel ratio sensor - open)
P2238, P2252 (Air fuel ratio sensor - low impedance)
P2239, P2253 (Air fuel ratio sensor - high impedance)
Auxiliary battery voltage
8 V or more
Time after engine start
3 seconds or more
Starter
OFF
Engine coolant temperature at engine start
-10°C (14°F) or more
Engine coolant temperature
-10°C (14°F) or more, and less than 50°C (122°F)
Engine idling time
0 seconds or more
Fuel-cut
OFF
Vehicle speed
Less than 37.5 mph (60 km/h)
Atmospheric pressure
76 kPa(abs) [570 mmHg(abs)] or more

TYPICAL MALFUNCTION THRESHOLDS


Accumulated mass air flow
Less than 32.5 g (varies with engine coolant temperature)

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure) (Click here).
  4. Turn the power switch off and wait for at least 30 seconds.
  5. Put the engine in inspection mode (maintenance mode) (Click here).
  6. Start the engine and warm it up for 5 minutes or more.
  7. Stop the engine.
  8. Leave the vehicle outside overnight.
  9. Turn the power switch on (IG) and turn the Techstream on [A].
  10. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.
  11. Check that "Coolant Temp" in the Data List is within the range of -10 to 50°C (14 to 122°F).
  12. Put the engine in inspection mode (maintenance mode) (Click here).
  13. Start the engine and warm it up until the coolant temperature is the same as the coolant temperature in the freeze frame data.
  14. Idle the engine for 1 minute or more.
  15. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  16. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  17. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  18. Input the DTC: P050A.
  19. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, idle the engine for 3 minutes, let the engine cool down, and then perform steps [A] and [B].

  20. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P0102 .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P050A)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC P050A is output
    A
    DTC P050A and other DTCs are output
    B

    HINT:
    If any DTCs other than P050A are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING TECHSTREAM (FUEL TRIM)

HINT:
Calculate the total fuel trim values to check the characteristic deviation of the mass air flow meter sub-assembly.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Gas AF Control / Short FT #1 and Long FT #1.

  1. Read the values displayed on the Techstream at engine idle.

  1. Add together the Short FT #1 and Long FT #1 values to obtain the total Fuel Trim.

    Result:
    Total of Short FT #1 and Long FT #1 values is between -20% and 20%.



NG
Go to step 7
OK


3.INSPECT THROTTLE BODY ASSEMBLY
  1. Check for deposits around the throttle valve and check the throttle valve condition.

    OK:
    No deposits around throttle valve and throttle valve moves smoothly.



NG
Go to step 6
OK


4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or more.

    HINT:
    The A/C switch and all accessory switches should be off.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Throttle Idle Position and MAP.

  1. Check that the Throttle Idle Position in ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.

    HINT:
    1. Do not leave the EGR valve open for 10 seconds or more during the Active Test.
    2. Be sure to return the EGR valve to step 0 when the Active Test is completed.
    3. Do not open the EGR valve 30 steps or more during the Active Test.

    OK:
    MAP and idling condition change in response to EGR step position when Throttle Idle Position is ON in Data List.


    Standard:

    -
    EGR Step Position (Active Test)
    0 Steps
    0 to 30 Steps
    Idling condition
    (Throttle Idle Position: ON)
    Steady idling
    Idling changes from steady to rough idling or engine stalls
    MAP
    (Data List)
    MAP value is 20 to 40 kPa (150 to 300 mmHg)
    (EGR valve is fully closed)
    MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed

    HINT:
    During Active Test, if the idling condition does not change in response to EGR step position, then there is probably a malfunction in the EGR valve.



OK
Go to step 19

NG
Go to step 5

5.INSPECT EGR VALVE ASSEMBLY
  1. Remove the EGR valve assembly (Click here).

  1. Check if the EGR valve is stuck open.

    OK:
    EGR valve is tightly closed.



OK
Go to step 19

NG
Go to step 17

6.REPAIR OR REPLACE THROTTLE BODY ASSEMBLY
  1. Repair or replace the throttle body assembly (Click here).

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the throttle body assembly (Click here).



NEXT
Go to step 19

7.CHECK PCV SYSTEM
  1. Check the PCV hose connections.

    OK:
    PCV valve and hose are connected correctly and are not damaged.



NG
Go to step 14
OK


8.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks (Click here).

    OK:
    No leaks from the intake system.



NG
Go to step 15
OK


9.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Visually check that the air cleaner filter element sub-assembly is not excessively contaminated with dirt or oil.

    OK:
    Air cleaner filter element sub-assembly is not excessively contaminated with dirt or oil.



NG
Go to step 16
OK


10.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or more.

    HINT:
    The A/C switch and all accessory switches should be off.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Throttle Idle Position and MAP.

  1. Check that the Throttle Idle Position in ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.

    HINT:
    1. Do not leave the EGR valve open for 10 seconds or more during the Active Test.
    2. Be sure to return the EGR valve to step 0 when the Active Test is completed.
    3. Do not open the EGR valve 30 steps or more during the Active Test.

    OK:
    MAP and idling condition change in response to EGR step position when Throttle Idle Position is ON in Data List.


    Standard:

    -
    EGR Step Position (Active Test)
    0 Steps
    0 to 30 Steps
    Idling condition
    (Throttle Idle Position: ON)
    Steady idling
    Idling changes from steady to rough idling or engine stalls
    MAP
    (Data List)
    MAP value is 20 to 40 kPa (150 to 300 mmHg)
    (EGR valve is fully closed)
    MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed

    HINT:
    During Active Test, if the idling condition does not change in response to EGR step position, then there is probably a malfunction in the EGR valve.



OK
Go to step 12

NG
Go to step 11

11.INSPECT EGR VALVE ASSEMBLY
  1. Remove the EGR valve assembly (Click here).

  1. Check if the EGR valve is stuck open.

    OK:
    EGR valve is tightly closed.



NG
Go to step 17
OK


12.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY)
  1. Operate the VVT system through the Active test, and check if the VVT system is operating normally.

    1. Perform the Active Test, referring to DTC P0011 Inspection Procedure .



NG
Go to step 18
OK


13.READ VALUE USING TECHSTREAM (MAF)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / MAF, Coolant Temp and Engine Speed.

  1. Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.

  1. Read MAF with the engine speed at 2500 rpm.

    Standard:
    Between 4.5 gm/sec and 8.5 gm/sec (shift position: P).

    HINT:
    During charging control, the engine speed is set at idle. Therefore, the engine speed does not increase when depressing the accelerator pedal. In this case, read the Data List after charging control has completed.



OK
Go to step 19

NG
Go to step 20

14.REPAIR OR REPLACE PCV HOSE
  1. Repair or replace the PCV hose.



NEXT
Go to step 19

15.REPAIR OR REPLACE INTAKE SYSTEM
  1. Repair or replace the intake system.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the intake system (Click here).



NEXT
Go to step 19

16.REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Replace the air cleaner filter element sub-assembly.



NEXT
Go to step 19

17.REPLACE EGR VALVE ASSEMBLY
  1. Replace the EGR valve assembly (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the EGR valve assembly (Click here).



NEXT
Go to step 19

18.CHECK AND REPAIR VVT SYSTEM
  1. Check and repair the VVT system.

    HINT:
    Refer to DTC P0011 Inspection Procedure (Click here).


NEXT


19.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)

NOTICE:
In this operation, the engine must be cold (approximately the same level as the engine coolant temperature recorded in the freeze frame data).

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the power switch off and wait for at least 30 seconds.

  1. Turn the power switch on (IG) and turn the Techstream on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.

  1. Check that the engine coolant temperature is between -10°C and 50°C (14°F and 122°F).

  1. Start the engine.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P050A.

  1. Check the DTC judgment result.

    Result 
    Result
    Proceed to
    NORMAL (DTC is not output)
    A
    ABNORMAL (DTC P050A is output)
    B



B
Go to step 20
A

END 

20.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
  1. Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM (Click here).

    HINT:
    Repair any problems.


NEXT


21.CHECK WHETHER DTC OUTPUT RECURS

NOTICE:
In this operation, the engine must be cold (approximately the same as the engine coolant temperature recorded in the freeze frame data).

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the power switch off and wait for at least 30 seconds.

  1. Turn the power switch on and turn the Techstream on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.

  1. Check that the engine coolant temperature is between -10°C and 50°C (14°F and 122°F).

  1. Start the engine.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Check the DTC judgment result.

    Result 
    Result
    Proceed to
    ABNORMAL (DTC P050A is output)
    A
    NORMAL (DTC is not output)
    B



B
END
A


22.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
  1. Disconnect the mass air flow meter sub-assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    D5-5 (VG) - D28-94 (VG)
    Always
    Below 1 Ω
    D5-4 (E2G) - D28-117 (E2G)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    D5-5 (VG) or D28-94 (VG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


23.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
  1. Replace the mass air flow meter sub-assembly (Click here).

    HINT:
    1. If the result of the inspection performed in step 13 indicated no problem, proceed to the next step without replacing the mass air flow meter sub-assembly.
    2. Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (Click here).


NEXT


24.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NOTICE:
In this operation, the engine must be cold (approximately the same level as the engine coolant temperature recorded in the freeze frame data).

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the power switch off and wait for at least 30 seconds.

  1. Turn the power switch on (IG) and turn the Techstream on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.

  1. Check that the engine coolant temperature is between -10°C and 50°C (14°F and 122°F).

  1. Start the engine.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P050A.

  1. Check the DTC judgment result.

    Result 
    Result
    Proceed to
    NORMAL (DTC is not output)
    A
    ABNORMAL (DTC P050A is output)
    B



B
REPLACE ECM (Click here)
A

END