Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM

DTC    B1794    Open in Occupant Classification ECU Battery Positive Line

for Preparation Click here


DESCRIPTION

DTC B1794 is stored when a malfunction is detected in the occupant classification ECU battery positive line.

DTC No.
DTC Detections Conditions
Trouble Areas
B1794
  1. The occupant classification ECU receives an open circuit signal in the occupant classification ECU battery positive line.
  2. Occupant classification ECU malfunction
  1. Auxiliary battery
  2. ECU-B fuse
  3. Wire harness
  4. Occupant classification ECU

HINT:
When DTC B1650/32 is detected as a result of troubleshooting for the airbag system, check the DTCs stored in the occupant classification ECU. When DTC B1794 is output, perform troubleshooting for the DTC.


WIRING DIAGRAM


C212172E05


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK AUXILIARY BATTERY VOLTAGE
  1. Measure the voltage of the auxiliary battery.

    Standard Voltage:
    11 to 14 V



NG
INSPECT AUXILIARY BATTERY (Click here)
OK


2.CHECK WIRE HARNESS (SOURCE VOLTAGE)


    C169182E15
  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Disconnect the connector from the occupant classification ECU.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    W3-1 (+B) - Body ground
    Always
    11 to 14 V

  1. Turn the power switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W3-3 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Occupant Classification ECU)



NG
REPLACE WIRE HARNESS
OK


3.CHECK DTC
  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Connect the connector to the occupant classification ECU.

  1. Connect the Techstream to the DLC3.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).

  1. Clear the DTCs stored in the occupant classification ECU (Click here).

  1. Clear the DTCs stored in the center airbag sensor assembly (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG), and wait for at least 10 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1794 is not output.

    HINT:
    Codes other than DTC B1794 may be output at this time, but they are not related to this check.



NG
Go to step 4
OK

USE SIMULATION METHOD TO CHECK (Click here)  

4.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Replace the occupant classification ECU (Click here).


NEXT


5.PERFORM ZERO POINT CALIBRATION
  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Using the Techstream, perform Zero Point Calibration (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.


NEXT


6.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform Sensitivity Check (Click here).

    Standard:
    27 to 33 kg (59.5 to 72.8 lb)


NEXT

END