Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › IGNITION SYSTEM

IGNITION SYSTEM > ON-VEHICLE INSPECTION

for Preparation Click here



1. PERFORM SPARK TEST
  1. Check for DTCs (Click here).

    NOTICE:
    If any DTC is present, perform troubleshooting in accordance with the procedure for that DTC.

  1. Remove the ignition coils and spark plugs (Click here).

  1. Disconnect the 4 fuel injector connectors.



    A216910
  1. Set the vehicle to the inspection mode (Click here).



    A216911
  1. Install the spark plug into the ignition coil, and then connect the ignition coil connector. (step 4)

  1. Ground the spark plug. (step 5)

  1. Check that spark occurs while the engine is being cranked. (step 6)

    NOTICE:
    1. Be sure to ground the spark plugs when checking them.
    2. Do not crank the engine for more than 2 seconds.
      Cranking will stop if the power switch is pushed again for models with cranking holding function.
    3. If a spark plug has been struck or dropped, replace it.
    4. If an ignition coil assembly has been struck or dropped, replace it.

    HINT:
    Repeat steps 4 to 6 for each spark plug and ignition coil.
    If spark does not occur, perform the following procedure for the malfunctioning cylinder.



    A216910
  1. Connect the 4 fuel injector connectors.

  1. Install the ignition coils and spark plugs (Click here).

  1. Check for DTCs (Click here).

  1. Clear the DTCs (Click here).



2. INSPECT IGNITION COIL AND SPARK TEST
  1. Check that the ignition coil connector is securely connected.

    Result:
    Result
    Action
    NG
    Connect securely
    OK
    Go to next step

  1. Perform a spark test.

    1. Replace the ignition coil with a known good one.

    2. Set the vehicle to the inspection mode (Click here).

    3. Perform the spark test again.

      Result:
      Result
      Action
      NG
      Go to next step
      OK
      Replace ignition coil

  1. Perform a spark test.

    1. Replace the spark plug with a known good one.

    2. Set the vehicle to the inspection mode (Click here).

    3. Perform the spark test again.

      Result:
      Result
      Action
      NG
      Inspect the ignition system (Click here)
      OK
      Replace the spark plug



3. INSPECT SPARK PLUG


    I039522E30
  1. Check the electrode.
    Text in Illustration 
    *1
    Ground

    1. Using a megohmmeter, measure the resistance.

      Standard Resistance:
      10 MΩ or more

      If the result is 10 MΩ or less, clean the plug and measure the resistance again.

      HINT:
      If a megohmmeter is not available, perform the following simple inspection instead.



    A126881
  1. Alternative inspection method:

    1. Quickly accelerate the engine to 4000 rpm 5 times.

    2. Remove each spark plug.

    3. Visually check the spark plug.
      If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.

  1. Check the spark plug for any damage to its threads and insulator.
    If there is any damage, replace the spark plug.
    Recommended Spark Plug 
    Manufacturer
    Spark Plug Type
    DENSO
    SC20HR11



    A126880E31
  1. Check the spark plug electrode gap.
    Text in Illustration 
    *1
    Spark Plug Electrode Gap

    Maximum Electrode Gap for Used Spark Plug:
    Electrode Gap
    1.3 mm (0.0512 in.)

    If the gap is greater than the maximum, replace the spark plug.

    Electrode Gap for New Spark Plug:
    Electrode Gap
    1.0 to 1.1 mm (0.0394 to 0.0433 in.)



    B062019E01
  1. Clean the spark plugs.
    If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

    Standard air pressure:
    588 kPa (6.0 kgf/cm2, 85 psi)

    Standard duration:
    20 seconds or less.

    HINT:
    Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.