Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM (for Start Function)

SMART KEY SYSTEM (for Start Function) > Power Source Mode does not Change to ON (IG and ACC)

for Preparation Click here


DESCRIPTION

When the power switch is pushed with the electrical key in the cabin, the power management control ECU receives signals to change the power source mode.

HINT:
To allow use of the Techstream to inspect the push-button start function when the power source mode is off, repeat opening and closing any of the doors. Opening and closing a door establishes communication between the Techstream and the power management control ECU. (Opening and closing a door can also be simulated by operating a door courtesy light switch.)


WIRING DIAGRAM


B331576E01


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - POWER MANAGEMENT CONTROL ECU)
  1. Disconnect the L5 and L6 connectors from the power management control ECU.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L5-1 (AM22) - Body ground
    Always
    9.5 to 16 V
    L6-7 (AM21) - Body ground
    Always
    9.5 to 16 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - POWER MANAGEMENT CONTROL ECU)
OK


Go to step 4

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L5-5 (E01) - Body ground
    Always
    Below 1 Ω
    L5-6 (E1) - Body ground
    Always
    Below 1 Ω
    L6-4 (E12) - Body ground
    Always
    Below 1 Ω
    L6-5 (E02) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)
OK


Go to step 5

3.READ VALUE USING TECHSTREAM
  1. Reconnect the L5 and L6 connectors to the power management control ECU.

  1. Turn the power switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Power Source Control / Data List.

  1. Read the Data List according to the display on the Techstream.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Key Certification Waiting Timed Out
    Key certification error detection/ No or Yes
    No: Key certification error not detected
    Yes: Key certification error detected
    -

    OK:
    When more than 1 second elapses after the power switch is turned from off to on (IG), No is displayed in the Data List.



NG
Go to step 9
OK


4.READ VALUE USING TECHSTREAM
  1. Read the Data List according to the display on the Techstream.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Start Switch1
    Start switch 1/ON or OFF
    ON: Power switch pushed
    OFF: Power switch not pushed
    -
    Start Switch2
    Start switch 2/ON or OFF
    ON: Power switch pushed
    OFF: Power switch not pushed
    -

    OK:
    ON (power switch is pushed) and OFF (power switch is not pushed) appear on the screen.



NG
Go to step 7
OK


5.CHECK POWER MANAGEMENT CONTROL ECU
  1. Read the Data List according to the display on the Techstream.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Power Supply Condition
    Power supply condition/All OFF, ACC ON, IG1 ON, IG2 ON, ST ON
    ALL OFF: All relays off
    ACC ON: ACC relay on
    IG1 ON: IG1 relay on
    IG2 ON: IG2 relay on
    ST ON: ST request signal on
    -

  1. Measure the voltage while checking the Data List on the Techstream.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L6-2 (IG1D) - Body ground
    Power switch off
    Below 1 V
    L6-2 (IG1D) - Body ground
    Power switch on (ACC)
    Below 1 V
    L6-2 (IG1D) - Body ground
    Power switch on (IG)
    Output voltage at terminal AM21 or AM22 is -2.5 V or more
    A22-2 (IG2D) - Body ground
    Power switch off
    Below 1 V
    A22-2 (IG2D) - Body ground
    Power switch on (ACC)
    Below 1 V
    A22-2 (IG2D) - Body ground
    Power switch on (IG)
    Output voltage at terminal AM21 or AM22 is -2.5 V or more
    L6-1 (ACCD) - Body ground
    Power switch off
    Below 1 V
    L6-1 (ACCD) - Body ground
    Power switch on (IG)
    Output voltage at terminal AM21 or AM22 is -2.5 V or more
    L6-1 (ACCD) - Body ground
    Power switch on (ACC)
    Output voltage at terminal AM21 or AM22 is -2.5 V or more



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK


6.CONFIRMATION TEST
  1. Check that the power source mode becomes on (ACC) and on (IG) when the power switch is operated.

    OK:
    Power source mode becomes on (ACC) and on (IG) when the power switch is operated.



NG
CHECK RELAY CONTACT SIDE CIRCUIT
OK

USE SIMULATION METHOD TO CHECK (Click here)  

7.CHECK POWER SWITCH


    C164809E17
  1. Remove the power switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L43-7 (SS1) - L43-5 (GND)
    Pushed
    Below 1 Ω
    L43-7 (SS1) - L43-5 (GND)
    Not pushed
    10 kΩ or higher
    L43-2 (SS2) - L43-5 (GND)
    Pushed
    Below 1 Ω
    L43-2 (SS2) - L43-5 (GND)
    Not pushed
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (Power Switch)



NG
REPLACE POWER SWITCH (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (POWER SWITCH - POWER MANAGEMENT CONTROL ECU AND BODY GROUND)
  1. Disconnect the L5 and L6 connectors from the power management control ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L6-17 (SSW2) - L43-2 (SS2)
    Always
    Below 1 Ω
    L5-7 (SSW1) - L43-7 (SS1)
    Always
    Below 1 Ω
    L6-17 (SSW2) - Body ground
    Always
    10 kΩ or higher
    L5-7 (SSW1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SWITCH - POWER MANAGEMENT CONTROL ECU OR BODY GROUND)
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)  

9.CHECK FOR DTC
  1. Enter the following menus: Body Electrical / Power Source Control and Smart Key / DTC.

  1. Check for DTCs.

    Result:
    Result
    Proceed to
    The following DTCs are not output:
    1. B2785
    2. B2287
    3. B2784
    A
    DTC B2785 is not output but DTC B2287 is output.
    B
    DTCs other than B2287 are output.
    C



A
GO TO OTHER FLOW CHART (Room Oscillator does not Recognize Key) (Click here)

B
GO TO OTHER FLOW CHART (DTC B2287)
C

GO TO DIAGNOSTIC TROUBLE CODE CHART