Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM

DTC    P2237    Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)

DTC    P2238    Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)

DTC    P2239    Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)

DTC    P2252    Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)

DTC    P2253    Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)

for Preparation Click here


DESCRIPTION

Refer to DTC P2195 .

DTC No.
DTC Detection Condition
Trouble Area
P2237
Open in the circuit between terminals A1A+ and A1A- of the air fuel ratio sensor while engine is running
(2 trip detection logic)
  1. Open in air fuel ratio sensor (sensor 1) circuit
  2. Air fuel ratio sensor (sensor 1)
  3. ECM
P2238
  1. Case 1
    Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic):
    (a) A1A+ voltage is 0.5 V or less
    (b) A1A+ - A1A- is 0.1 V or less
  2. Case 2
    Air fuel ratio sensor admittance is less than 0.0074 1/Ω (2 trip detection logic)
  1. Open or short in air fuel ratio sensor (sensor 1) circuit
  2. Air fuel ratio sensor (sensor 1)
  3. ECM
P2239
A1A+ voltage is more than 4.5 V for 5 seconds
(2 trip detection logic)
  1. Open or short in air fuel ratio sensor (sensor 1) circuit
  2. Air fuel ratio sensor (sensor 1)
  3. ECM
P2252
A1A- voltage is 0.5 V or less for 5 seconds
(2 trip detection logic)
  1. Open or short in air fuel ratio sensor (sensor 1) circuit
  2. Air fuel ratio sensor (sensor 1)
  3. ECM
P2253
A1A- voltage is more than 4.5 V for 5 seconds
(2 trip detection logic)
  1. Open or short in air fuel ratio sensor (sensor 1) circuit
  2. Air fuel ratio sensor (sensor 1)
  3. ECM

MONITOR DESCRIPTION

These DTCs are output when there is an open or short in the air fuel ratio sensor circuit, or if air fuel ratio sensor output drops.
To detect these problems, the voltage of the air fuel ratio sensor is monitored when turning the power switch on (IG), and the admittance (admittance is an electrical term that indicates the ease of flow of current) is checked while driving. If the voltage of the air fuel ratio sensor is between 0.6 V and 4.5 V, it is considered normal. If the voltage is outside of the specified range, or the admittance is below the standard value, the ECM will determine that there is a malfunction in the air fuel ratio sensor. If the same malfunction is detected in the next driving cycle, the MIL is illuminated and a DTC is stored.

MONITOR STRATEGY


Related DTCs
P2237: Air fuel ratio sensor open circuit between A1A+ and A1A-
P2238: Air fuel ratio sensor short circuit between A1A+ and A1A-
P2238: Air fuel ratio sensor short circuit between A1A+ and GND
P2238: Air fuel ratio sensor low impedance
P2239: Air fuel ratio sensor short circuit between A1A+ and +B
P2252: Air fuel ratio sensor short circuit between A1A- and GND
P2253: Air fuel ratio sensor short circuit between A1A- and +B
Required Sensors/Components (Main)
Air fuel ratio sensor
Required Sensors/Components (Related)
Engine coolant temperature sensor
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
10 seconds: P2237, P2238 (Air fuel ratio sensor low impedance)
5 seconds: Others
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


P2237 and P2238 
Monitor runs whenever following DTCs are not present
P0016 (VVT system bank 1 - misalignment)
P0031, P0032, P101D (Air fuel ratio sensor heater - sensor 1)
P0102, P0103 (Mass air flow meter)
P0107, P0108 (Manifold absolute pressure)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0128 (Thermostat)
P0171, P0172 (Fuel system)
P0301, P0302, P0303, P0304 (Misfire)
P0335 (Crankshaft position sensor)
P0401 (EGR system (closed))
P0451, P0452, P0453 (EVAP system)
P0505 (Idle speed control)
P219A, P219C, P219D, P219E, P219F (Air fuel ratio sensor - imbalance)

Other 
Monitor runs whenever following DTCs are not present
None

P2237 (Air Fuel Ratio Sensor Open Circuit Between A1A+ and A1A-) 
Estimated sensor temperature
450 to 550°C (842 to 1022°F)
Engine
Running
Auxiliary battery voltage
11 V or more
Power switch
On (IG)
Time after power switch is off to on (IG)
5 seconds or more

P2238 (Air Fuel Ratio Sensor Low Impedance) 
Estimated sensor temperature
700 to 800°C (1292 to 1472°F)
Engine coolant temperature
5°C (41°F) or more
Fuel cut
Not executed

Other 
Auxiliary battery voltage
11 V or more
Power switch
On (IG)
Time after power switch is off to on (IG)
5 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


P2237 (Air Fuel Ratio Sensor Open Circuit Between A1A+ and A1A-) 
Air fuel ratio sensor admittance
Below 0.002 1/Ω

P2238 (Air Fuel Ratio Sensor Low Impedance) 
Air fuel ratio sensor admittance
Below 0.0074 1/Ω

P2238 (Air Fuel Ratio Sensor Short Circuit Between A1A+ and GND) 
A1A+ terminal voltage
0.5 V or less

P2238 (Air Fuel Ratio Sensor Short Circuit Between A1A+ and A1A-) 
Difference between A1A+ terminal and A1A- terminal voltage
0.1 V or less

P2239 (Air Fuel Ratio Sensor Short Circuit Between A1A+ and +B) 
A1A+ terminal voltage
More than 4.5 V

P2252 (Air Fuel Ratio Sensor Short Circuit Between A1A- and GND) 
A1A- terminal voltage
0.5 V or less

P2253 (Air Fuel Ratio Sensor Short Circuit Between A1A- and +B) 
A1A- terminal voltage
More than 4.5 V

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the power switch off and wait for at least 30 seconds.
  5. Turn the power switch on (IG) and turn the Techstream on.
  6. Put the engine in inspection mode (maintenance mode) (Click here).
  7. Start the engine and wait 5 minutes.
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P2237, P2238, P2239, P2252 or P2253.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, idle the engine for 5 minutes and check the DTC judgment result again.

  13. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P2195 .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Refer to "Data List / Active Test" [AFS Voltage B1S1] (Click here).
  2. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. Sensor 1 refer to the sensor closest to the engine assembly.
  4. Sensor 2 refers to the sensor farthest away from the engine assembly.

1.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    D24-1 (HA1A) - D28-18 (HA1A)
    Always
    Below 1 Ω
    D24-3 (A1A+) - D28-103 (A1A+)
    Always
    Below 1 Ω
    D24-4 (A1A-) - D28-126 (A1A-)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    D24-1 (HA1A) or D28-18 (HA1A) - Body ground
    Always
    10 kΩ or higher
    D24-3 (A1A+) or D28-103 (A1A+) - Body ground
    Always
    10 kΩ or higher
    D24-4 (A1A-) or D28-126 (A1A-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here).


NEXT


3.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the power switch off and wait for at least 30 seconds.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P2237, P2238, P2239, P2252 or P2253.

  1. Check the DTC judgment.

    Result 
    Result
    Proceed to
    NORMAL (DTC is not output)
    A
    ABNORMAL (DTC P2237, P2238, P2239, P2252 or P2253 is output)
    B



B
REPLACE ECM (Click here)
A

END