Home › Engine / Hybrid System › CRUISE CONTROL › LANE-KEEPING ASSIST SYSTEM

DTC    U1119    Lost Communication with Object Recognition ECU (CAN)

for Preparation Click here


DESCRIPTION

Because of the location of the lane recognition camera assembly, it is subject to high temperatures. If the lane recognition camera sensor assembly becomes too hot, the power source is shut down to protect the system. At that time CAN communication also stops. However, in order to inform the driving support ECU that CAN communication has not stopped because of a CAN communication error, on/off signals are periodically sent from the HITP terminal.

DTC No.
DTC Detection Condition
Trouble Area
U1119
When vehicle speed is 50 km/h (31 mph) or more with lane-keeping main switch is on, communication stop from lane recognition camera sensor to driving support ECU continues for 1 second or more
  1. Lane recognition camera sensor
  2. CAN communication system
  3. Driving support ECU
  4. Harness or connector

WIRING DIAGRAM


A216941E04


INSPECTION PROCEDURE

HINT:
This circuit uses CAN communication. Therefore, if there are any malfunctions in the communication circuit, one or more DTCs in the CAN communication system are output.

1.CHECK DTC OUTPUT
  1. Using the Techstream, enter the following menus: All ECUs / Lane Keeping Assist / Trouble Codes.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC U1119 is output
    A
    DTC other than U1119 is output
    B



B
GO TO CAN COMMUNICATION CIRCUIT (Click here)
A


2.READ VALUE USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: All ECUs / Pre-Collision 2/ Data List / Recog ECU H Temp Hist.

  1. Confirm the judgment history.

    Pre-Collision 2 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Recog ECU H Temp Hist
    Lane-recognition ECU temperature condition history/
    ON or OFF
    ON: No history of excessive temperature
    OFF: History of excessive temperature
    -

    Result:
    Result
    Proceed to
    ON is displayed
    A
    OFF is displayed
    B



B
Go to step 6
A


3.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU - LANE RECOGNITION CAMERA SENSOR)
  1. Disconnect the driving support ECU connector and lane recognition camera sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    U4-5 (HITP) - L60-24 (HITP)
    Always
    Below 1 Ω
    U4-5 (HITP) or L60-24 (HITP) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the connectors.



NG
Go to step 4
OK

REPLACE LANE RECOGNITION CAMERA SENSOR ASSEMBLY (Click here)  

4.REPAIR OR REPLACE HARNESS OR CONNECTOR (DRIVING SUPPORT ECU - LANE RECOGNITION CAMERA SENSOR)
  1. Repair or replace harness or connector.


NEXT


5.CHECK DTC OUTPUT
  1. Using the Techstream, enter the following menus: All ECUs / Lane Keeping Assist / Trouble Codes.

  1. Clear the DTC (Click here).

  1. Turn the power switch off.

  1. Start the engine.

  1. Drive the vehicle and operate lane keeping assist control.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC U1119 is not output
    A
    DTC U1119 is output
    B



B
GO TO CAN COMMUNICATION CIRCUIT (Click here)
A

END 

6.CHECK CAN COMMUNICATION SYSTEM
  1. Check CAN communication system (Click here).



NG
GO TO CAN COMMUNICATION CIRCUIT (Click here)
OK


7.REPLACE LANE RECOGNITION CAMERA SENSOR ASSEMBLY
  1. Replace the lane recognition camera sensor assembly (Click here).

  1. Adjust the lane recognition camera sensor assembly (Click here).


NEXT


8.CHECK DTC OUTPUT
  1. Using the Techstream, enter the following menus: All ECUs / Lane Keeping Assist / Trouble Codes.

  1. Clear the DTCs (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG).

  1. Drive the vehicle and operate lane keeping assist control.

  1. Recheck for DTCs.

    OK:
    DTC is not output.



NG
REPLACE DRIVING SUPPORT ECU (Click here)
OK

END