Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM

DTC    C1A50    Brake System

for Preparation Click here


DESCRIPTION

When the driving support ECU receives an electronically controlled brake system malfunction signal from the brake booster with master cylinder (skid control ECU) via the CAN communication line, DTC C1A50 is stored.

DTC No.
DTC Detection Condition
Trouble Area
C1A50
When signal malfunction from brake booster with master cylinder (skid control ECU) continues for 1 second while dynamic radar cruise control is operating
  1. Electronically controlled brake system
  2. Driving support ECU

WIRING DIAGRAM


E187973E06


INSPECTION PROCEDURE

1.READ OUTPUT DTC (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.

  1. Read the DTCs.

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM (Click here)
A


2.CHECK WHETHER DTC OUTPUT RECURS (DTC C1A50)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Clear the DTCs (Click here).

  1. Perform the following to make sure that the DTC detection conditions are met.

    HINT:
    If the detection conditions are not met, the malfunction cannot be detected.

    1. Drive the vehicle at a speed for which cruise control operation is possible.

    2. Turn the cruise control main switch on.

    3. Push the -SET switch to activate the cruise control.

  1. Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.

  1. Read the DTCs.

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC C1A50 is output
    B



B
Go to step 3
A

USE SIMULATION METHOD TO CHECK (Click here)  

3.REPLACE DRIVING SUPPORT ECU
  1. Replace the driving support ECU (Click here).


NEXT


4.CHECK WHETHER DTC OUTPUT RECURS (DTC C1A50)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Clear the DTCs (Click here).

  1. Perform the following to make sure that the DTC detection conditions are met.

    HINT:
    If the detection conditions are not met, the malfunction cannot be detected.

    1. Drive the vehicle at a speed for which cruise control operation is possible.

    2. Turn the cruise control main switch on.

    3. Push the -SET switch to activate the cruise control.

  1. Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.

  1. Read the DTCs.

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC C1A50 is output
    B



B
Go to step 5
A

END 

5.REPLACE BRAKE BOOSTER WITH MASTER CYLINDER
  1. Replace the brake booster with master cylinder (skid control ECU) (Click here).


NEXT


6.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Clear the DTCs (Click here).

  1. Perform the following to make sure that the DTC detection conditions are met.

    HINT:
    If the detection conditions are not met, the malfunction cannot be detected.

    1. Drive the vehicle at a speed for which cruise control operation is possible.

    2. Turn the cruise control main switch on.

    3. Push the -SET switch to activate the cruise control.

  1. Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.

  1. Read the DTCs.

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC C1A50 is output
    B



B
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
A

END