DTC P050B Cold Start Ignition Timing Performance |

| DTC No. | DTC Detection Condition | Trouble Area |
| P050B | Insufficient ignition retard at cold start (2 trip detection logic) |
|
| Related DTCs | P050B: Cold start ignition timing performance |
| Required Sensors/Components (Main) | Throttle body assembly |
| Required Sensors/Components (Related) | Mass air flow meter sub-assembly Engine coolant temperature sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | 10 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs are not present | P0010 (Camshaft timing oil control valve bank 1) P0011 (VVT system bank 1- advance) P0012 (VVT system bank 1- retard) P0016 (VVT system bank 1 - misalignment) P0102, P0103 (Mass air flow meter) P0107, P0108 (Manifold absolute pressure) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P014C, P014D (Air fuel ratio sensor - slow response) P015A, P015B (Air fuel ratio sensor - delayed response) P0171, P0172 (Fuel system) P0301, P0302, P0303, P0304 (Misfire) P0335 (Crankshaft position sensor) P0340, P0342, P0343 (Camshaft position sensor) P0351, P0352, P0353, P0354 (Igniter) P0401 (EGR system (closed)) P2195, P2196 (Air fuel ratio sensor - rationality) P219A, P219C, P219D, P219E, P219F (Air fuel ratio sensor - imbalance) P2237 (Air fuel ratio sensor - open) P2238, P2252 (Air fuel ratio sensor - low impedance) P2239, P2253 (Air fuel ratio sensor - high impedance) |
| Auxiliary battery voltage | 8 V or more |
| Time after engine start | 3 seconds or more |
| Starter | OFF |
| Engine coolant temperature at engine start | -10°C (14°F) or more |
| Engine coolant temperature | -10°C (14°F) or more, and less than 50°C (122°F) |
| Fuel-cut | OFF |
| Engine idling time | 0 seconds or more |
| Vehicle speed | Less than 37.5 mph (60 km/h) |
| Atmospheric pressure | 76 kPa(abs) [570 mmHg(abs)] or more |
| Accumulated time when ignition timing retard is cut off | 8 seconds or more |
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| Symptom | Factor | Trouble Area |
| Low idle speed at engine cold. (immediately after engine start) | Excessive engine friction | Engine oil deterioration |
| Rough idle at engine cold. (immediately after engine start) | Abnormal combustion | Fuel quality |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P050B) |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following the menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P050B is output | A |
| DTC P050B and other DTCs are output | B |
|
| ||||
| A | |
| 2.READ VALUE USING TECHSTREAM (FUEL TRIM) |
Connect the Techstream to the DLC3.
Turn the power switch on (IG) and turn the Techstream on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / Gas AF Control / Short FT #1 and Long FT #1.
Read the values displayed on the Techstream at engine idle.
Add together the Short FT #1 and Long FT #1 values to obtain the total fuel trim.
|
| ||||
| OK | |
| 3.INSPECT THROTTLE BODY ASSEMBLY |
Check for deposits around the throttle valve and check the throttle valve condition.
|
| ||||
| OK | |
| 4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION) |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or more.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Throttle Idle Position and MAP.
Check that the Throttle Idle Position in ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| Idling condition (Throttle Idle Position: ON) | Steady idling | Idling changes from steady to rough idling or engine stalls |
| MAP (Data List) | MAP value is 20 to 40 kPa (150 to 300 mmHg) (EGR valve is fully closed) | MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
|
| ||||
|
| ||||
| 5.INSPECT EGR VALVE ASSEMBLY |
Remove the EGR valve assembly (Click here).
Check if the EGR valve is stuck open.
|
| ||||
|
| ||||
| 6.REPAIR OR REPLACE THROTTLE BODY ASSEMBLY |
Repair or replace the throttle body assembly (Click here).
|
| ||||
| 7.CHECK PCV HOSE (HOSE CONNECTIONS) |
Check the PCV hose connections .
|
| ||||
| OK | |
| 8.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks (Click here).
|
| ||||
| OK | |
| 9.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
Visually check that the air cleaner filter element sub-assembly is not excessively contaminated with dirt or oil.
|
| ||||
| OK | |
| 10.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION) |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or more.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Throttle Idle Position and MAP.
Check that the Throttle Idle Position in ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| Idling condition (Throttle Idle Position: ON) | Steady idling | Idling changes from steady to rough idling or engine stalls |
| MAP (Data List) | MAP value is 20 to 40 kPa (150 to 300 mmHg) (EGR valve is fully closed) | MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
|
| ||||
|
| ||||
| 11.INSPECT EGR VALVE ASSEMBLY |
Remove the EGR valve assembly (Click here).
Check if the EGR valve is stuck open.
|
| ||||
| OK | |
| 12.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY) |
Operate the VVT system through the Active test, and check if the VVT system is operating normally.
Perform the Active Test, referring to DTC P0011 Inspection Procedure .
|
| ||||
| OK | |
| 13.READ VALUE USING TECHSTREAM (MAF) |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / MAF, Coolant Temp and Engine Speed.
Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.
Read MAF with the engine speed at 2500 rpm.
|
| ||||
|
| ||||
| 14.REPAIR OR REPLACE PCV HOSE |
Repair or replace the PCV hose.
|
| ||||
| 15.REPAIR OR REPLACE INTAKE SYSTEM |
Repair or replace the intake system.
|
| ||||
| 16.REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
Replace the air cleaner filter element sub-assembly.
|
| ||||
| 17.REPLACE EGR VALVE ASSEMBLY |
Replace the EGR valve assembly (Click here).
|
| ||||
| 18.CHECK AND REPAIR VVT SYSTEM |
Check and repair the VVT system.
| NEXT | |
| 19.CHECK WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG) and turn the Techstream on.
Put the engine in inspection mode (maintenance mode) (Click here).
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.
Check that the engine coolant temperature is between -10°C and 50°C (14°F and 122°F).
Start the engine.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P050B.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P050B is output) | B |
|
| ||||
| A | ||
| ||
| 20.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION) |
Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM (Click here).
| NEXT | |
| 21.CHECK WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on and turn the Techstream on.
Put the engine in inspection mode (maintenance mode) (Click here).
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.
Check that the engine coolant temperature is between -10°C and 50°C (14°F and 122°F).
Start the engine.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P050B.
Check the DTC judgment result.
| Result | Proceed to |
| ABNORMAL (DTC P050B is output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | |
| 22.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM) |
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D5-5 (VG) - D28-94 (VG) | Always | Below 1 Ω |
| D5-4 (E2G) - D28-117 (E2G) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| D5-5 (VG) or D28-94 (VG) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 23.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY |
Replace the mass air flow meter sub-assembly (Click here).
| NEXT | |
| 24.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG) and turn the Techstream on.
Put the engine in inspection mode (maintenance mode) (Click here).
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.
Check that the engine coolant temperature is between -10°C and 50°C (14°F and 122°F).
Start the engine.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P050B.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P050B is output) | B |
|
| ||||
| A | ||
| ||