Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM

DTC    P219A    Bank 1 Air-Fuel Ratio Imbalance

DTC    P219C    Cylinder 1 Air-Fuel Ratio Imbalance

DTC    P219D    Cylinder 2 Air-Fuel Ratio Imbalance

DTC    P219E    Cylinder 3 Air-Fuel Ratio Imbalance

DTC    P219F    Cylinder 4 Air-Fuel Ratio Imbalance

for Preparation Click here


DESCRIPTION

Refer to DTC P0300 .
Refer to DTC P2195 .

DTC No.
DTC Detection Condition
Trouble Area
P219A
The difference in air fuel ratio between the cylinders exceeds the threshold (2 trip detection logic).
  1. Fuel injector assembly
  2. Intake system
  3. Gas leak from exhaust system
  4. Ignition system
  5. Compression pressure
  6. Air fuel ratio sensor (sensor 1)
  7. ECM
P219C
The difference in air fuel ratio between the cylinders exceeds the threshold (2 trip detection logic).
  1. Fuel injector assembly
  2. Intake system
  3. Gas leak from exhaust system
  4. Ignition system
  5. Compression pressure
  6. Air fuel ratio sensor (sensor 1)
  7. ECM
P219D
The difference in air fuel ratio between the cylinders exceeds the threshold (2 trip detection logic).
  1. Fuel injector assembly
  2. Intake system
  3. Gas leak from exhaust system
  4. Ignition system
  5. Compression pressure
  6. Air fuel ratio sensor (sensor 1)
  7. ECM
P219E
The difference in air fuel ratio between the cylinders exceeds the threshold (2 trip detection logic).
  1. Fuel injector assembly
  2. Intake system
  3. Gas leak from exhaust system
  4. Ignition system
  5. Compression pressure
  6. Air fuel ratio sensor (sensor 1)
  7. ECM
P219F
The difference in air fuel ratio between the cylinders exceeds the threshold (2 trip detection logic).
  1. Fuel injector assembly
  2. Intake system
  3. Gas leak from exhaust system
  4. Ignition system
  5. Compression pressure
  6. Air fuel ratio sensor (sensor 1)
  7. ECM

MONITOR DESCRIPTION

  1. Fuel System Air Fuel Ratio Cylinder Imbalance Monitor
    The ECM uses the air fuel ratio sensor and crankshaft position sensor to monitor the difference in air fuel ratio between the cylinders caused by differences in injection volume between the cylinders, leakage in the intake or exhaust system, etc.
    When the air fuel ratios of the cylinders are lean or rich with respect to each other, the ECM determines that a problem is present and stores a DTC.
  1. Air Fuel Ratio Sensor Monitoring Method: P219A is stored primarily when a rich side imbalance is detected.
    When the system detects a difference in the air fuel ratio between the cylinders due to fluctuation of the air fuel ratio sensor output over 1 engine cycle (2 crankshaft revolutions), the system determines that there is a problem.
  1. Crankshaft Position Sensor Monitoring Method: P219A, P219C, P219D, P219E and/or P219F are stored primarily when a lean side imbalance is detected.
    The system monitors the engine speed variation and when the variation becomes large, the system determines that there is a difference in the air fuel ratio between the cylinders, which it determines to be a problem.

MONITOR STRATEGY


Related DTCs
P219A: Air fuel ratio cylinder imbalance monitor
P219C: Air fuel ratio cylinder imbalance monitor (cylinder 1)
P219D: Air fuel ratio cylinder imbalance monitor (cylinder 2)
P219E: Air fuel ratio cylinder imbalance monitor (cylinder 3)
P219F: Air fuel ratio cylinder imbalance monitor (cylinder 4)
Required Sensors/Components (Main)
Air fuel ratio sensor, Crankshaft position sensor
Required Sensors/Components (Related)
Mass air flow meter sub-assembly, Engine coolant temperature sensor
Frequency of Operation
Once per driving cycle
Duration
10 to 15 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


P219A: 
Monitor runs whenever following DTCs are not present
P0010 (Camshaft timing oil control valve assembly)
P0011 (VVT system - advance)
P0012 (VVT system - retard)
P0016 (VVT system - misalignment)
P0031, P0032, P101D (Air fuel ratio sensor heater)
P0102, P0103 (Mass air flow meter)
P0107, P0108 (Manifold absolute pressure)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343 (Camshaft position sensor)
P0351, P0352, P0353, P0354 (Igniter)
P0401 (EGR system)

Other: 
Monitor runs whenever following DTCs are not present
None

Air Fuel Ratio Sensor Monitoring Method 
Air fuel ratio sensor status
Activated
Engine speed
2000 rpm or more, and less than 2500 rpm
Engine coolant temperature
75°C (167°F) or higher
Atmospheric pressure
76 kPa(abs) [570 mmHg(abs)] or higher
Fuel system status
Closed loop
Mass air flow
16 g/sec or more, and less than 22 g/sec

Crankshaft Position Sensor Monitoring Method (First Judgment) 
Engine speed
1800 rpm or more, and less than 2200 rpm
Engine Load
35% or more, and less than 50%
Engine coolant temperature
75°C (167°F) or higher
Air fuel ratio sensor status
Activated
Fuel system status
Closed loop
Auxiliary battery voltage
11 V or higher

Crankshaft Position Sensor Monitoring Method (Second Judgment) 
Vehicle speed
Less than 1.865 mph (3 km/h)
Engine speed
1050 rpm or more, and less than 1350 rpm
Engine coolant temperature
75°C (167°F) or higher
Air fuel ratio sensor status
Activated
Fuel system status
Closed loop
Auxiliary battery voltage
11 V or higher

TYPICAL MALFUNCTION THRESHOLDS


P219A: Air Fuel Ratio Sensor Monitoring Method (Bank 1) 
Air fuel ratio sensor monitoring method criteria
0.046 or more

Crankshaft Position Sensor Monitoring Method (First Judgment) 
Crankshaft position sensor monitoring method criteria (first judgment)
1.5 or more

Crankshaft Position Sensor Monitoring Method (Second Judgment) 
Crankshaft position sensor monitoring method criteria (second judgment)
1 or more

HINT:
If the first judgment while driving shows that the value of Engine Speed Fluctuation Average is between 0.5 and 1.5, then second judgment will be performed when the vehicle is stopped and the engine is idling.


MONITOR RESULT

Refer to Checking Monitor Status (Click here).

CONFIRMATION DRIVING PATTERN


A288663E01

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG) and turn the Techstream on.
  3. Put the engine in inspection mode (maintenance mode) (Click here).
  4. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].
  5. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

    CAUTION:
    Use the Techstream to clear the DTCs. (Do not disconnect the cable from negative (-) auxiliary battery terminal to clear the DTCs.)

  6. Drive the vehicle at 40 km/h (25 mph).
  7. Gradually accelerate the vehicle from 40 km/h (25 mph) to 80 km/h (50 mph) taking approximately 10 to 20 seconds [B].

    HINT:
    Refer to mass air flow and engine speed in Typical Enabling Conditions, and then accelerate the vehicle to 80 km/h (50 mph).

  8. Drive the vehicle at 80 km/h (50 mph) or higher for 1 minute or more [C].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    Electrical load can be applied while the vehicle is driven.

  9. Idle the engine for 1 minute or more [D].

    HINT:
    With the shift lever in D.

  10. Repeat steps [B] and [D] above at least 3 times [E].
  11. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [F].
  12. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  13. Drive the vehicle at 80 km/h (50 mph).
  14. Gradually accelerate the vehicle from 80 km/h (50 mph) to 100 km/h (62 mph) taking approximately 5 to 15 seconds [G].

    HINT:
    Refer to mass air flow and engine speed in Typical Enabling Conditions, and then accelerate the vehicle to 100 km/h (62 mph).

  15. Drive the vehicle at 100 km/h (62 mph) or higher for 1 minute or more [H].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    Electrical load can be applied while the vehicle is driven.

  16. Idle the engine for 1 minute or more [I].

    HINT:
    With the shift lever in D.

  17. Repeat steps [G] and [I] above at least 2 times [J].
  18. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [K].
  19. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  20. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  21. Input the DTC: P219A, P219C, P219D, P219E or P219F.
  22. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the following procedure.

  23. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to Fuel Injector Circuit .

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. When any air-fuel ratio imbalance is detected, the ECM will perform air-fuel ratio feedback control to make the air-fuel ratio close to the stoichiometric level. This may result in an air-fuel ratio imbalance of normal cylinders and DTCs may be stored.

1.CHECK ANY OTHER DTCS OUTPUT
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch to on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    DTC P219A, P219C, P219D, P219E and/or P219F is output
    A
    DTC P219A, P219C, P219D, P219E and/or P219F and other DTCs are output
    B

HINT:
If any DTCs other than P219A, P219C, P219D, P219E and/or P219F are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING TECHSTREAM (FREEZE FRAME DATA)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Using the Techstream, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Freeze Frame Data Items for DTC P219A, P219C, P219D, P219E and/or P219F:
    1. Vehicle Speed
    2. Engine Speed
    3. Calculate Load
    4. Short FT #1
    5. Long FT #1
    6. Cylinder #1 Misfire Count to Cylinder #4 Misfire Count

    HINT:
    When the sum of Short FT and Long FT is positive, the engine is running lean, and when the sum is negative, the engine is running rich.


    Air Fuel Ratio Sensor Monitoring Method (P219A)
    Crankshaft Position Sensor Monitoring Method (P219C, P219D, P219E and P219F)
    Note
    DTCs are output
    DTC is output (Only one DTC relating to a single cylinder is output)
    Malfunctioning of cylinders detected by Crankshaft Position Sensor Monitoring Method is primarily suspected
    DTCs are output
    DTCs are output (Multiple DTCs relating to multiple cylinders are output)
    Malfunctioning of cylinders except ones detected by Crankshaft Position Sensor Monitoring Method is primarily suspected.*1
    DTCs are not output
    DTCs are output
    Malfunctioning of cylinders detected by Crankshaft Position Sensor Monitoring Method is primarily suspected.
    DTCs are output
    DTCs are not output
    Malfunctioning of the bank detected by Air Fuel Ratio Sensor Monitoring Method is primarily suspected
    *1: When any air-fuel ratio imbalance is detected, the ECM will perform air-fuel ratio feedback control to make the air-fuel ratio close to the stoichiometric level. This may result in an air-fuel ratio imbalance of normal cylinders and DTCs may be stored.


NEXT


3.READ DTC OUTPUT
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

    HINT:
    1. If any misfire count ("Cylinder #1 Misfire Count" to "Cylinder #4 Misfire Count) increases while idling or driving the vehicle, proceed to step 6.
    2. Perform inspections while focusing on the cylinder whose misfire count has increased.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P219A is output
    A
    DTC P219A and P219C, P219D, P219E or P219F is output
    B
    DTC P219C, P219D, P219E and/or P219F is output



B
Go to step 6
A


4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Warm up the engine.

    HINT:
    The A/C switch and all accessory switches should be off.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / Data List / Cylinder #1 to #4 Misfire Count.

    HINT:
    When the "Control the Injection Volume" Active Test is selected (injection volume is 0%), if a misfire count increases, proceed to step 6 (Check Intake System).

  1. Perform the Control the Injection Volume operation with the engine idling.

  1. Check the misfire counts ("Cylinder #1 Misfire Count" to "Cylinder #4 Misfire Count") while decreasing the injection volume in 5% increments.

    NOTICE:
    Do not decrease the injection volume by more than 20%.

    Result:
    The cylinder whose misfire count has not increased can be assumed to be running rich. Therefore, perform inspections while focusing on that cylinder.


NEXT


5.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No exhaust gas leaks.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the exhaust system (Click here).



NG
REPAIR OR REPLACE EXHAUST SYSTEM
OK


6.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks (Click here).

    OK:
    No leaks in intake system.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the intake system (Click here).



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


7.INSPECT SPARK PLUG
  1. Inspect the spark plug of the imbalanced cylinder .

    HINT:
    Perform "Inspection After Repair" after replacing the spark plug (Click here).



NG
REPLACE SPARK PLUG (Click here)
OK


8.CHECK FOR SPARK (SPARK TEST)
  1. Perform a spark test .

    HINT:
    1. If the result of the spark test is normal, proceed to the next step.
    2. Perform "Inspection After Repair" after repairing or replacing the ignition system (Click here).


NEXT


9.CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder .

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the engine assembly (Click here).



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR)


    A194154E74
  1. Disconnect the ECM connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    D28-85 (#10) - D28-109 (E01)
    Power switch on (IG)
    11 to 14 V
    D28-84 (#20) - D28-109 (E01)
    Power switch on (IG)
    11 to 14 V
    D28-83 (#30) - D28-109 (E01)
    Power switch on (IG)
    11 to 14 V
    D28-82 (#40) - D28-109 (E01)
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
CHECK FUEL INJECTOR CIRCUIT (Click here)
OK


11.CHECK FUEL INJECTOR ASSEMBLY OF IMBALANCE CYLINDER
  1. Check the fuel injector injection [whether fuel volume is high or low, and whether injection pattern is poor] (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the fuel injector assembly (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


12.CHECK FOR CAUSE OF FAILURE
  1. If the diagnosis procedure has been performed and the malfunctioning part cannot be determined, perform the following inspection.

  1. Check for deposits on the intake valves.

    HINT:
    The DTC may have been stored due to deposits that have accumulated in the intake valve. Therefore, remove the cylinder head and inspect the intake valves.

  1. Check for deposits in the EGR delivery chamber.

    HINT:
    The DTC may have been stored due to deposits that have accumulated in the EGR delivery chamber. Therefore, remove and inspect the EGR delivery chamber.


NEXT


13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Check for DTCs.

    Result:
    DTC is not output.


NEXT

END