Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT SEAT SIDE AIRBAG ASSEMBLY

FRONT SEAT SIDE AIRBAG ASSEMBLY > REMOVAL

for Preparation Click here


CAUTION:
  1. Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.
  2. If the front seat side airbag assembly was deployed, replace the front seat side airbag assembly, separate type front seatback spring assembly, separate type front seatback cover or separate type front seatback pad with the necessary parts in accordance with the extent of the collision damage.
    for Manual Seat: (Click here)
    for Power Seat: (Click here)

HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedure listed below is for the LH side.



1. PRECAUTION

CAUTION:
Be sure to read Precaution thoroughly before servicing (Click here).

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).



2. REMOVE REAR NO. 2 FLOOR BOARD (for Separate Type)


    B227787E01
  1. Disengage the 2 guides <A> as shown in the illustration.

  1. Disengage the 3 guides <B> and remove the rear No. 2 floor board.



3. REMOVE REAR DECK FLOOR BOX
  1. Remove the rear deck floor box.



4. REMOVE REAR NO. 3 FLOOR BOARD


    B227791
  1. Disengage the 2 guides and remove the rear No. 3 floor board.



5. DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL (for Manual Seat)

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



6. REMOVE FRONT SEAT HEADREST ASSEMBLY


7. REMOVE OUTER SEAT TRACK COVER (for Manual Seat)
  1. Lift up the seat track adjusting handle and move the seat to the foremost position.



    B229805
  1. Disengage the 2 claws and remove the outer seat track cover.



8. REMOVE OUTER SEAT TRACK BRACKET COVER (for Power Seat)
  1. Operate the power seat switch knob and move the seat to the foremost position.



    B292166
  1. Disengage the 2 claws and remove the outer seat track bracket cover.



9. REMOVE INNER SEAT TRACK COVER (for Manual Seat)


    B229803
  1. Disengage the claw and guide, remove the inner seat track cover.



10. REMOVE INNER SEAT TRACK BRACKET COVER (for Power Seat)


    B292167
  1. Disengage the guide and claw and remove the inner seat track bracket cover.



11. REMOVE FRONT SEAT ASSEMBLY (for Manual Seat)


    B229807
  1. Remove the 2 bolts on the rear side of the seat.

  1. Lift up the seat track adjusting handle and move the seat to the rearmost position.



    B229808
  1. Remove the 2 bolts on the front side of the seat.

  1. Lift up the seat track adjusting handle and move the seat to the center position. Also, operate the reclining adjuster release handle and move the seatback to the upright position.

  1. w/ Vertical Adjuster:

    1. Lift up the vertical adjusting handle and move the seat to upright position.

  1. Disconnect each connector and clamp under the seat.

  1. Remove the front seat assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



12. REMOVE FRONT SEAT ASSEMBLY (for Power Seat)


    B251949
  1. Remove the 2 bolts on the rear side of the seat.

  1. Operate the power seat switch knob and move the seat to the rearmost position.



    B251948
  1. Remove the 2 bolts on the front side of the seat.

  1. Operate the power seat switch knob and move the seat to the center position. Also, operate the power seat switch knob and move the seatback to the upright position.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative auxiliary (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the connectors under the seat.

  1. Remove the front seat assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



13. DISCONNECT FRONT SEAT SIDE AIRBAG ASSEMBLY WIRE HARNESS


    B252715
  1. Disconnect the rubber band.



  1. for LH Side:



      B333364
    1. Disengage the claw and 3 clamps to separate the front seat side airbag assembly wire harness.

    2. Disconnect the front seat side airbag assembly wire harness from the seat clamp.



  1. for RH Side:



      B333366
    1. Disengage the claw and 3 clamps to separate the front seat side airbag assembly wire harness.

    2. Disconnect the front seat side airbag assembly wire harness from the seat clamp.



  1. w/ Seat Heater System:



      B324532
    1. Disconnect the seat heater wire harness connector and disengage the clamp.

  1. Disengage the fastener and separate the front seat side airbag assembly wire harness.



14. REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for Manual Seat)


    B299227
  1. Remove the 2 hog rings.



    B299231
  1. Remove the 3 hog rings.



    B299235
  1. Pull out the lower part of 2 fasteners from the separate type front seatback cover as shown in the illustration.



    B299239
  1. Open the 2 fasteners.



    B229850E01
  1. Remove the 3 hog rings and disconnect the 2 fastening rubbers.
    Text in Illustration 
    *1
    Fastening Rubber



    B301043
  1. Disengage the 2 hooks.



    B301044
  1. Turn back the separate type front seatback cover and remove the nut, and remove the bracket of the separate type front seatback cover.



    B229856
  1. Disengage the 4 claws and remove the 2 front seat headrest supports.

  1. Remove the separate type front seatback cover with pad from the separate type front seatback spring sub-assembly.



15. REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for Power Seat)


    B299227
  1. Remove the 2 hog rings.



    B299231
  1. Remove the 3 hog rings.



    B299235
  1. Pull out the lower part of 2 fasteners from the separate type front seatback cover as shown in the illustration.



    B299239
  1. Open the 2 fasteners.



    B251968E01
  1. Remove the 3 hog rings and disconnect the 2 fastening rubbers.
    Text in Illustration 
    *1
    Fastening Rubber



    B299243
  1. Disengage the 2 hooks.



    B302489
  1. Turn back the separate type front seatback cover to remove the nut, and separate the bracket of the separate type front seatback cover.



    B229856
  1. Disengage the 4 claws and remove the 2 front seat headrest supports.

  1. Remove the separate type front seatback cover with pad from the separate type front seatback spring assembly.



16. REMOVE FRONT SEAT SIDE AIRBAG ASSEMBLY


    B312071
  1. Disengage the 2 clamps.

  1. Remove the 2 nuts and the front seat side airbag assembly.

    CAUTION:
    1. The nuts must not be reused.
    2. Make sure that the separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.