Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C1202/68    Master Reservoir Level Malfunction

for Preparation Click here


DESCRIPTION

When a fluid level drop in the brake master cylinder reservoir assembly is detected, a signal is sent to the skid control ECU.
If the DTC for the fluid level drop is memorized, the warning will be canceled and the DTC will not be stored when the fluid level returns to normal.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
C1202/68
371
An open is detected in the switch signal circuit for 2 seconds or more.
  1. Brake fluid level warning switch (Brake master cylinder reservoir assembly) internal open circuit
  2. Open in wire harness
  3. Skid control ECU (Brake booster with master cylinder assembly)
↑
-
The reservoir level remains low.
  1. Low brake fluid level
  2. Brake fluid leaks
  3. Brake fluid level warning switch (Brake master cylinder reservoir assembly) internal short circuit
  4. Short in wire harness
  5. Brake disc rotor excessive wear
  6. Skid control ECU (Brake booster with master cylinder assembly)

WIRING DIAGRAM


C209586E17


INSPECTION PROCEDURE

NOTICE:
Before replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (Click here).

HINT:
Before releasing the parking brake, chock the wheels for safety.

1.CHECK BRAKE FLUID LEVEL
  1. Check that the brake fluid level is sufficient.

    OK:
    Brake fluid level is sufficient.

    HINT:
    If the fluid level is low, check for fluid leaks, and repair as necessary.

    1. Check for brake fluid leaks (Connection between the brake booster pump assembly, brake master cylinder reservoir assembly and brake booster with master cylinder assembly, and the brake booster with master cylinder assembly and wheel cylinders).

      HINT:
      If no leaks exist, add and adjust fluid using the intelligent tester (Click here).

    2. Check that the DTC is not output again (Click here).

  1. Check that there are no leaks from the connections between the brake booster pump assembly and brake booster with master cylinder assembly.

    HINT:
    As a visual check is very difficult, perform the check with the following procedure.

    1. Bleed the air from the brake system (Click here).

    2. Connect the intelligent tester to the DLC3.

    3. Turn the power switch on (IG).

    4. Select the Data List on the intelligent tester (Click here).

      ABS/VSC/TRC 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Accumulator Sensor
      Accumulator pressure sensor / Min.: 0.00 V, Max.: 5.00 V
      Specified value: 2.90 to 4.20 V
      When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator

    5. Wait for 30 seconds without depressing the brake pedal.

    6. Check that the accumulator pressure sensor output value change is within the specified range.

      OK:
      Accumulator pressure sensor output value change is less than 0.55 V.



NG
CHECK AND REPAIR BRAKE FLUID LEAKS OR ADD FLUID
OK


2.INSPECT BRAKE FLUID LEVEL WARNING SWITCH


    C230719E04
  1. Turn the power switch off (lock).

  1. Remove the reservoir filler cap.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the brake fluid level warning switch (brake master cylinder reservoir assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    A float is located inside the reservoir. Its position changes according to the level of brake fluid.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (+) - 1 (E)
    Brake fluid level warning switch OFF (Float up)
    1.84 to 2.16 kΩ
    2 (+) - 1 (E)
    Brake fluid level warning switch ON (Float down)
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly))

    Result:

    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (Click here)

C
REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (Click here)
A


3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE FLUID LEVEL WARNING SWITCH)
  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A41-36 (LBL) - A27-2 (+)
    Always
    Below 1 Ω
    A41-36 (LBL) - Body ground
    Always
    10 kΩ or higher
    A27-1 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT SKID CONTROL ECU (SWITCH INPUT)


    C247950E08
  1. Reconnect the skid control ECU (brake booster with master cylinder assembly) connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A27-2 (+) - Body ground
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly))

    Result:

    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)

C
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)
A


5.CHECK BRAKE DISC
  1. Turn the power switch off (lock).

  1. Reconnect the brake fluid level warning switch (brake master cylinder reservoir assembly) connector.

  1. Disconnect the brake pedal stroke sensor assembly connector.

  1. Perform a road test according to Freeze Frame Data or customer problem analysis. While driving, check for abnormal brake pedal vibration caused by brake discs that are worn or have excess runout.

    OK:
    Brake pedal does not vibrate during braking.

    HINT:
    1. An unevenly worn disc may vibrate the caliper pistons and cause fluctuations in brake line pressure, triggering a malfunction detection condition.
    2. The brake pedal does not kick back due to caliper piston vibration during electronically controlled brake system control.
    3. If the brake pedal stroke sensor assembly connector is disconnected, the fail-safe function will prohibit electronically controlled brake system control.
    4. The Active Test does not prohibit electronically controlled brake system control when the vehicle is being driven, so disconnect the brake pedal stroke sensor assembly connector before continuing with inspection.
    5. Uneven disc wear can be checked by measuring the disc thickness variation (Click here for front, or Click here for rear).



NG
REPLACE BRAKE DISC
OK


6.RECONFIRM DTC
  1. Reconnect the brake pedal stroke sensor assembly connector.

  1. Clear the DTCs (Click here).

  1. Turn the power switch on (ready).

  1. Perform a road test.

  1. Check if the same DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC C1202/68 is not output.
    A
    DTC C1202/68 is output (for LHD).
    B
    DTC C1202/68 is output (for RHD).
    C

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)

C
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)