DTC P3190 Poor Engine Power |
DTC P3191 Engine does not Start |
DTC P3193 Fuel Run Out |
| DTC No. | DTC Detection Condition | Trouble Area |
| P3190 | Following conditions continue at a fixed engine speed or a fixed length of time (1 trip detection logic):
|
|
| P3191 | Following conditions continue at a fixed engine speed or a fixed length of time (1 trip detection logic):
|
|
| P3193 | Fuel low level signal input into ECM (1 trip detection logic). |
|
| Frequency of Operation | Continuous |
| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P3190, P3191 AND/OR P3193) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P3190, P3191 and/or P3193 are output | A |
| DTC P3190, P3191 and/or P3193 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK SHORTAGE OF FUEL |
Check the amount of fuel remaining.
|
| ||||
| OK | |
| 3.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks (Click here).
|
| ||||
| OK | |
| 4.CHECK FOR UNUSUAL NOISE OR VIBRATION WHEN STARTING ENGINE OR REVVING UP |
|
| ||||
| OK | |
| 5.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 6.INSPECT FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC / Freeze Frame Data.
Calculate the requested torque* and compare it with Actual Engine Torque.
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 7.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY |
Inspect the throttle body with motor assembly (Click here).
|
| ||||
| OK | |
| 8.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY |
Inspect the mass air flow meter sub-assembly (Click here).
|
| ||||
| OK | |
| 9.INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
Inspect the engine coolant temperature sensor (Click here).
|
| ||||
| OK | |
| 10.INSPECT CRANK POSITION SENSOR |
Inspect the crank position sensor (Click here).
|
| ||||
| OK | |
| 11.REPLACE CAM POSITION SENSOR |
Replace the cam position sensor (Click here).
| NEXT | |
| 12.CHECK WHETHER DTC OUTPUT RECURS (DTC P3190, P3191 AND/OR P3193) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG) and turn the tester on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine.
Allow the engine to idle for 10 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the pending DTCs.
| Result | Proceed to |
| DTC P3190, P3191 and/or P3193 is output | A |
| DTC is not output | B |
|
| ||||
| A | |
| 13.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE EGR STEP POSITION) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Data List / All Data / Throttle Idle Position and MAP.
Confirm that the Throttle Idle Position is ON and check the MAP value in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| MAP (Data List) | (EGR valve is fully closed) | MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
| Result | Proceed to |
| Outside of standard range | A |
| Within standard range | B |
|
| ||||
| A | |
| 14.INSPECT EGR VALVE ASSEMBLY |
Remove the EGR valve assembly (Click here).
Check if the EGR valve is stuck open.
|
| ||||
| OK | |
| 15.REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG) and turn the tester on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine.
Allow the engine to idle for 10 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P3190, P3191 or P3193.
Check the DTC judgment result.
| NEXT | ||
| ||