Home › Vehicle Exterior › VEHICLE PROXIMITY NOTIFICATION SYSTEM › VEHICLE PROXIMITY NOTIFICATION SYSTEM

VEHICLE PROXIMITY NOTIFICATION SYSTEM > There is No Sound Made

for Preparation Click here


DESCRIPTION

The vehicle approaching speaker controller receives stop light switch signals from the stop light switch assembly, vehicle speed signals from the combination meter assembly, engine oil pressure switch signals from the engine oil pressure switch assembly and P position switch signals from the lower shift lever assembly, and produces the warning sound from the vehicle approaching speaker assembly.

WIRING DIAGRAM


E342154E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK DTC OUTPUT
  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Trouble Codes.

  1. Check for DTCs.

    Result:
    Result
    Proceed to
    DTC B1350 is not output
    A
    DTC B1350 is output
    B
    Communication with the GTS is not possible
    C



B
GO TO DTC CHART B1350 (Click here)

C
GO TO DIAGNOSTIC PROCEDURE (Communication between Vehicle Proximity Notification System and Diagnostic Tool is not Possible) (Click here)
A


2.PERFORM ACTIVE TEST USING GTS (Proximity Sound (Vehicle Stationary))
  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Active Test.

  1. Perform the Active Test according to the display on the GTS.

    Vehicle Proximity Notification System 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Proximity Sound (Vehicle Stationary)
    Proximity sound (Vehicle stationary)
    OFF or ON
    Produces warning sound when vehicle is stopped

    Result:
    Result
    Proceed to
    The warning sound is produced
    A
    The warning sound is not produced
    B



B
Go to step 10
A


3.READ VALUE USING GTS (Stop Light SW)
  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.

  1. Read the Data List according to the display on the GTS.

    Vehicle Proximity Notification System 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch / OFF or ON
    OFF: Brake pedal released
    ON: Brake pedal depressed
    -

    Result:
    Result
    Proceed to
    The GTS display changes according to brake pedal operation
    A
    The GTS display does not change according to brake pedal operation
    B



B
Go to step 12
A


4.READ VALUE USING GTS (Vehicle Speed)
  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.

  1. Read the Data List according to the display on the GTS.

    Vehicle Proximity Notification System 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Almost the same as actual vehicle speed
    -

    Result:
    Result
    Proceed to
    The GTS display changes according to the vehicle speed
    A
    The GTS display does not change according to the vehicle speed
    B



B
Go to step 14
A


5.READ VALUE USING GTS (Oil Pressure SW)
  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.

  1. Read the Data List according to the display on the GTS.

    Vehicle Proximity Notification System 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Oil Pressure SW
    Oil pressure switch / OFF or ON
    OFF: Engine started
    ON: Engine not started
    -

    Result:
    Result
    Proceed to
    The GTS display changes according to engine operation
    A
    The GTS display does not change according to engine operation
    B



B
Go to step 16
A


6.READ VALUE USING GTS (Shift Position)
  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.

  1. Read the Data List according to the display on the GTS.

    Vehicle Proximity Notification System 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Shift Position
    P position switch / Not Parking or Parking
    Not Parking or Parking
    -

    Result:
    Result
    Proceed to
    The GTS display changes according to the selected shift state
    A
    The GTS display does not change according to the selected shift state
    B



B
Go to step 7
A

REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER (Click here)  

7.CHECK VEHICLE APPROACHING SPEAKER CONTROLLER (SHIFT)
  1. Disconnect the G25 lower shift lever assembly connector.



    E289606E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G25-2 (P2) - Body ground
    Power switch on (IG)
    8 V or higher
    Power switch off
    Below 1 V

Text in Illustration 
*a
Front view of wire harness connector
(to Lower Shift Lever Assembly)


NG
Go to step 9
OK


8.CHECK LOWER SHIFT LEVER ASSEMBLY
  1. Reconnect the G25 lower shift lever assembly connector.



    E289963E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G25-2 (P2) - Body ground
    Power switch on (IG), park (P) selected
    8 V or higher
    Power switch on (IG), park (P) not selected
    Below 2.5 V

Text in Illustration 
*a
Component with harness connected
(Lower Shift Lever Assembly)


NG
REPLACE LOWER SHIFT LEVER ASSEMBLY (Click here)
OK

REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER (Click here)  

9.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - LOWER SHIFT LEVER ASSEMBLY)
  1. Disconnect the G85 vehicle approaching speaker controller connector.

  1. Disconnect the G25 lower shift lever assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G85-11 (SFTP) - G25-2 (P2)
    Always
    Below 1 Ω
    G85-11 (SFTP) or G25-2 (P2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER (Click here)  

10.INSPECT VEHICLE APPROACHING SPEAKER ASSEMBLY
  1. Remove the vehicle approaching speaker assembly (Click here).

  1. Inspect the vehicle approaching speaker assembly (Click here).



NG
REPLACE VEHICLE APPROACHING SPEAKER ASSEMBLY (Click here)
OK


11.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - VEHICLE APPROACHING SPEAKER ASSEMBLY)
  1. Disconnect the G85 vehicle approaching speaker controller connector.

  1. Disconnect the A64 vehicle approaching speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G85-3 (SP+) - A64-1 (+)
    Always
    Below 1 Ω
    G85-8 (SP-) - A64-2 (-)
    Always
    Below 1 Ω
    G85-3 (SP+) or A64-1 (+) - Body ground
    Always
    10 kΩ or higher
    G85-8 (SP-) or A64-2 (-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER (Click here)  

12.CHECK STOP LIGHT OPERATION
  1. Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

    OK:
    Condition
    Illumination Condition
    Brake pedal depressed
    On
    Brake pedal released
    Off



NG
GO TO LIGHTING SYSTEM (Click here)
OK


13.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - STOP LIGHT SWITCH ASSEMBLY)
  1. Disconnect the G85 vehicle approaching speaker controller connector.

  1. Disconnect the A65 stop light switch assembly connector.

  1. Disconnect the M5 rear combination light assembly LH connector.

  1. Disconnect the M6 rear combination light assembly RH connector.

  1. Disconnect the S2 center stop light set connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G85-2 (STP) - A65-2 (OUT)
    Always
    Below 1 Ω
    G85-2 (STP) or A65-2 (OUT) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER (Click here)  

14.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - COMBINATION METER ASSEMBLY)
  1. Disconnect the G85 vehicle approaching speaker controller connector.

  1. Disconnect the G1 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G85-6 (SPD) - G1-39 (+S)
    Always
    Below 1 Ω
    G85-6 (SPD) or G1-39 (+S) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


15.CHECK COMBINATION METER ASSEMBLY
  1. Reconnect the G85 vehicle approaching speaker controller connector.

  1. Reconnect the G1 combination meter assembly connector.



    B232574E22
  1. Check the input waveform.

    1. Remove the combination meter assembly with the connector(s) still connected.

    2. Connect an oscilloscope to terminal G1-39 (+S) and body ground.

    3. Turn the power switch on (IG).

    4. Turn a wheel slowly.

    5. Check the signal waveform according to the condition(s) in the table below.
      Item
      Condition
      Tool setting
      5 V/DIV., 20 ms./DIV.
      Vehicle condition
      Power switch on (IG), wheel being rotated
      Text in Illustration 
      *a
      Component with harness connected
      (Combination Meter Assembly)

      OK:
      The waveform is similar to that shown in the illustration.

      HINT:
      When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.



NG
GO TO METER / GAUGE SYSTEM (Click here)
OK

REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER (Click here)  

16.CHECK ENGINE OIL PRESSURE SWITCH ASSEMBLY (INPUT SIGNAL)
  1. Disconnect the G85 vehicle approaching speaker controller connector.



    E285131E15
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G85-12 (OPSW) - Body ground
    Idling*
    8 V or higher
    Power switch on (IG)
    Below 2 V

    HINT:
    *:Put the engine in inspection mode (Click here).

Text in Illustration 
*a
Front view of wire harness connector
(to Vehicle Approaching Speaker Controller)


NG
Go to step 17
OK

REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER (Click here)  

17.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - ENGINE OIL PRESSURE SWITCH ASSEMBLY)
  1. Disconnect the G85 vehicle approaching speaker controller connector.

  1. Disconnect the E2 engine oil pressure switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G85-12 (OPSW) - E2-1
    Always
    Below 1 Ω
    G85-12 (OPSW) or E2-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ENGINE OIL PRESSURE SWITCH ASSEMBLY (Click here)