DTC P0403 Exhaust Gas Recirculation Control Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0403 | Open or short in EGR valve circuit (1 trip detection logic). |
|
| Frequency of Operation | Continuous |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE EGR STEP POSITION) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Data List / All Data / Throttle Idle Position and MAP.
Confirm that the Throttle Idle Position is ON and check the MAP value in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| MAP (Data List) | (EGR valve is fully closed) | MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
|
| ||||
| OK | ||
| ||
| 2.INSPECT EGR VALVE ASSEMBLY |
Inspect the EGR valve assembly (Click here).
|
| ||||
| OK | |
| 3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EGR VALVE ASSEMBLY) |
![]() |
Disconnect the EGR valve assembly connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C18-5 (+B1) - Body ground | Power switch on (IG) | 11 to 14 V |
| C18-2 (+B2) - Body ground | Power switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector (to EGR Valve Assembly) |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (ECM - EGR VALVE ASSEMBLY) |
Disconnect the EGR valve assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C10-28 (EGR1) - C18-4 (EGR1) | Always | Below 1 Ω |
| C10-27 (EGR2) - C18-3 (EGR2) | Always | Below 1 Ω |
| C10-26 (EGR3) - C18-6 (EGR3) | Always | Below 1 Ω |
| C10-25 (EGR4) - C18-1 (EGR4) | Always | Below 1 Ω |
| C10-28 (EGR1) or C18-4 (EGR1) - Body ground | Always | 10 kΩ or higher |
| C10-27 (EGR2) or C18-3 (EGR2) - Body ground | Always | 10 kΩ or higher |
| C10-26 (EGR3) or C18-6 (EGR3) - Body ground | Always | 10 kΩ or higher |
| C10-25 (EGR4) or C18-1 (EGR4) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| C9-28 (EGR1) - C18-4 (EGR1) | Always | Below 1 Ω |
| C9-27 (EGR2) - C18-3 (EGR2) | Always | Below 1 Ω |
| C9-26 (EGR3) - C18-6 (EGR3) | Always | Below 1 Ω |
| C9-25 (EGR4) - C18-1 (EGR4) | Always | Below 1 Ω |
| C9-28 (EGR1) or C18-4 (EGR1) - Body ground | Always | 10 kΩ or higher |
| C9-27 (EGR2) or C18-3 (EGR2) - Body ground | Always | 10 kΩ or higher |
| C9-26 (EGR3) or C18-6 (EGR3) - Body ground | Always | 10 kΩ or higher |
| C9-25 (EGR4) or C18-1 (EGR4) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - NO. 1 INTEGRATION RELAY) |
Disconnect the EGR valve assembly connector.
Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C18-5 (+B1) - 2C-4 | Always | Below 1 Ω |
| C18-2 (+B2) - 2C-4 | Always | Below 1 Ω |
| C18-5 (+B1) or 2C-4 - Body ground | Always | 10 kΩ or higher |
| C18-2 (+B2) or 2C-4 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||