Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0225220 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1660/43  Passenger Airbag ON/OFF Indicator Circuit Malfunction  


DESCRIPTION

The passenger airbag ON/OFF indicator circuit consists of the airbag ECU assembly and passenger airbag ON/OFF indicator.

The passenger airbag ON/OFF indicator indicates the operation condition of the instrument panel passenger airbag assembly and front seat cushion airbag assembly RH*.

DTC B1660/43 is stored when a malfunction is detected in the passenger airbag ON/OFF indicator circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1660/43 Passenger Airbag ON/OFF Indicator Circuit Malfunction
·

The airbag ECU assembly detects a line short, short to ground or B+, or an open in the passenger airbag ON/OFF indicator circuit.

·

Passenger airbag ON/OFF indicator malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Instrument panel junction block assembly

·

Passenger airbag ON/OFF indicator (Meter circuit plate)

·

Airbag ECU assembly


Does not apply to test/check mode

*: w/ Occupant Classification System


WIRING DIAGRAM

C338142E01
5.448,2.906 5.979,3.125 0.531,0.219 10 false F56 5.448,3.073 7.052,3.375 1.604,0.302 10 false Airbag ECU Assembly 5.49,2.271 6.021,2.49 0.531,0.219 10 false E2 5.49,1.823 6.021,2.042 0.531,0.219 10 false E1 5.25,1.708 5.781,1.927 0.531,0.219 10 false 25 5.25,2.156 5.781,2.375 0.531,0.219 10 false 26 5.49,0.99 6.177,1.323 0.688,0.333 10 false P-AB 5.49,0.552 6.177,0.885 0.688,0.333 10 false PAON 5.24,0.438 5.927,0.771 0.688,0.333 10 false 23 5.24,0.875 5.927,1.208 0.688,0.333 10 false 17 4.281,0.438 4.969,0.771 0.688,0.333 10 false 8 4.271,0.875 4.958,1.208 0.688,0.333 10 false 46 2.771,0.438 3.458,0.771 0.688,0.333 10 false 29 2.771,0.875 3.458,1.208 0.688,0.333 10 false 51 2.365,1.219 3.052,1.552 0.688,0.333 10 false 3A 2.375,1.385 5.104,1.708 2.729,0.323 10 false Instrument Panel Junction Block Assembly 1.885,0.542 2.573,0.875 0.688,0.333 10 false F7 1.885,0.99 2.573,1.323 0.688,0.333 10 false F7 1.375,0.99 2.063,1.323 0.688,0.333 10 false P-AB 1.313,0.542 2,0.875 0.688,0.333 10 false PAON 1.927,0.333 2.615,0.667 0.688,0.333 10 false 3 1.927,0.781 2.615,1.115 0.688,0.333 10 false 4 1.885,1.604 2.573,1.938 0.688,0.333 10 false 21 1.885,1.813 2.573,2.146 0.688,0.333 10 false F6 1.479,1.813 2.167,2.146 0.688,0.333 10 false IG+ 0.563,2.917 2.854,3.438 2.292,0.521 10 false Passenger Airbag ON/OFF Indicator (Combination Meter Assembly) 2.458,1.969 3.438,2.302 0.979,0.333 10 false METER-IG2 2.854,2.51 4.281,2.802 1.427,0.292 10 false from IG2-NO. 2 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION
a.

Turn the power switch on (IG).


b.

Check the passenger airbag ON/OFF indicator operation.

HINT:

Refer to the normal condition of the passenger airbag ON/OFF indicator.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM



Result:
Result Proceed to
ON/OFF indicator illumination is always on. A
ON/OFF indicator illumination is always off. B



A

2.CHECK CONNECTORS

B

13.CHECK CONNECTORS
2.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly, combination meter assembly and instrument panel junction block assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly, combination meter assembly and instrument panel junction block assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION

NG

REPLACE INSTRUMENT PANEL WIRE

3.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION
a.

Connect the connector to the combination meter assembly and instrument panel junction block assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Check the passenger airbag ON/OFF indicator operation.

OK:

The passenger airbag ON/OFF indicator does not come on.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

5.CHECK WIRE HARNESS (OPEN)
4.CHECK DTC
a.
C284134C01
0.271,0.802 0.583,1.073 0.313,0.271 10 false *1 2.906,0.813 3.219,1.104 0.313,0.292 10 false *2 0.292,1.469 0.719,1.917 0.427,0.448 10 false *3 2.615,0.802 2.927,1.146 0.313,0.344 10 false A 2.427,0.802 2.74,1.198 0.313,0.396 10 false B 0.74,0.802 1.042,1.177 0.302,0.375 10 false C 0.552,0.802 0.865,1.094 0.313,0.292 10 false D 0.729,1.479 1.083,1.979 0.354,0.5 10 false E 0.563,1.479 0.875,1.635 0.313,0.156 10 false F
*1 Instrument Panel Junction Block Assembly
*2 Airbag ECU Assembly
*3 Combination Meter Assembly


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Connect the connector to the airbag ECU assembly.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1660/43 is not output.


HINT:

Codes other than DTC B1660/43 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG

5.CHECK WIRE HARNESS (OPEN)
a.
C348692C01
0.292,0.438 0.646,0.677 0.354,0.24 0.271,3.729 0.604,3.948 0.333,0.219 1.542,1.417 1.542,1.167 false 0.979,1.229 1.281,0.833 false 2.125,1.24 1.729,0.594 false 1,4.333 1.281,3.792 false 1.698,4.313 1.427,3.792 false 2.01,2.813 2.01,2.063 false 2.01,2.417 1.625,2.417 false 0.167,1.979 0.552,2.292 0.385,0.313 10 false *1 3,2 3.354,2.385 0.354,0.385 10 false *2 0.177,2.677 0.604,3.063 0.427,0.385 10 false *3 1.948,2.833 2.344,3.229 0.396,0.396 10 false *4 1.479,1.427 1.833,1.802 0.354,0.375 10 false *5 0.135,0.146 0.51,0.5 0.375,0.354 10 false *a 0.146,3.281 0.521,3.854 0.375,0.573 10 false *b 0.771,1.25 1.375,1.625 0.604,0.375 10 false PAON 1.979,1.25 2.583,1.625 0.604,0.375 10 false P-AB 0.354,0.479 0.958,0.854 0.604,0.375 10 false F56 0.365,3.76 0.969,4.135 0.604,0.375 10 false F7 2.698,2 3.135,2.427 0.438,0.427 10 false A 2.323,2 2.76,2.427 0.438,0.427 10 false B 0.625,2 1.063,2.427 0.438,0.427 10 false C 0.438,2 0.875,2.427 0.438,0.427 10 false D 0.823,2.677 1.26,3.104 0.438,0.427 10 false E 0.448,2.677 0.885,3.104 0.438,0.427 10 false F 1.542,4.333 2.063,4.594 0.521,0.26 10 false P-AB 0.802,4.333 1.302,4.542 0.5,0.208 10 false PAON
*1 Instrument Panel Junction Block Assembly
*2 Airbag ECU Assembly
*3 Combination Meter Assembly
*4 Instrument Panel Wire
*5 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Combination Meter Assembly)


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Disconnect the connector from the combination meter assembly.


d.

Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F7-3 (PAON) - F7-4 (P-AB) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK WIRE HARNESS (SHORT)

NG

12.CHECK INSTRUMENT PANEL WIRE (OPEN)
6.CHECK WIRE HARNESS (SHORT)
a.
C348693C01
0.313,2.375 0.615,2.594 0.302,0.219 1.958,1.333 1.958,0.583 false 1.958,0.958 1.635,0.958 false 1,3 1.302,2.438 false 1.74,3 1.458,2.438 false 3,0.521 3.313,0.885 0.313,0.365 10 false *2 0.188,0.51 0.583,0.75 0.396,0.24 10 false *1 0.198,1.198 0.573,1.406 0.375,0.208 10 false *3 1.896,1.354 2.25,1.573 0.354,0.219 10 false *4 0.167,1.854 0.531,2.323 0.365,0.469 10 false *a 2.698,0.521 3.01,0.885 0.313,0.365 10 false A 2.323,0.521 2.635,0.885 0.313,0.365 10 false B 0.635,0.521 0.948,0.885 0.313,0.365 10 false C 0.448,0.521 0.76,0.885 0.313,0.365 10 false D 0.823,1.198 1.135,1.563 0.313,0.365 10 false E 0.448,1.198 0.76,1.563 0.313,0.365 10 false F 0.396,2.406 0.76,2.875 0.365,0.469 10 false F7 0.813,3 1.427,3.219 0.615,0.219 10 false PAON 1.583,3 2.198,3.219 0.615,0.219 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag ECU Assembly
*3 Combination Meter Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F7-3 (PAON) - F7-4 (P-AB) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK WIRE HARNESS (SHORT TO B+)

NG

11.CHECK INSTRUMENT PANEL WIRE (SHORT)
7.CHECK WIRE HARNESS (SHORT TO B+)
a.
C348693C01
0.313,2.375 0.615,2.594 0.302,0.219 1.958,1.333 1.958,0.583 false 1.958,0.958 1.635,0.958 false 1,3 1.302,2.438 false 1.74,3 1.458,2.438 false 3,0.521 3.313,0.885 0.313,0.365 10 false *2 0.188,0.51 0.583,0.75 0.396,0.24 10 false *1 0.198,1.198 0.573,1.406 0.375,0.208 10 false *3 1.896,1.354 2.25,1.573 0.354,0.219 10 false *4 0.167,1.854 0.531,2.323 0.365,0.469 10 false *a 2.698,0.521 3.01,0.885 0.313,0.365 10 false A 2.323,0.521 2.635,0.885 0.313,0.365 10 false B 0.635,0.521 0.948,0.885 0.313,0.365 10 false C 0.448,0.521 0.76,0.885 0.313,0.365 10 false D 0.823,1.198 1.135,1.563 0.313,0.365 10 false E 0.448,1.198 0.76,1.563 0.313,0.365 10 false F 0.396,2.406 0.76,2.875 0.365,0.469 10 false F7 0.813,3 1.427,3.219 0.615,0.219 10 false PAON 1.583,3 2.198,3.219 0.615,0.219 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag ECU Assembly
*3 Combination Meter Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Combination Meter Assembly)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F7-3 (PAON) - Body ground Power switch on (IG) Below 1 V
F7-4 (P-AB) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

8.CHECK WIRE HARNESS (SHORT TO GROUND)

NG

10.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
8.CHECK WIRE HARNESS (SHORT TO GROUND)
a.
C348693C01
0.313,2.375 0.615,2.594 0.302,0.219 1.958,1.333 1.958,0.583 false 1.958,0.958 1.635,0.958 false 1,3 1.302,2.438 false 1.74,3 1.458,2.438 false 3,0.521 3.313,0.885 0.313,0.365 10 false *2 0.188,0.51 0.583,0.75 0.396,0.24 10 false *1 0.198,1.198 0.573,1.406 0.375,0.208 10 false *3 1.896,1.354 2.25,1.573 0.354,0.219 10 false *4 0.167,1.854 0.531,2.323 0.365,0.469 10 false *a 2.698,0.521 3.01,0.885 0.313,0.365 10 false A 2.323,0.521 2.635,0.885 0.313,0.365 10 false B 0.635,0.521 0.948,0.885 0.313,0.365 10 false C 0.448,0.521 0.76,0.885 0.313,0.365 10 false D 0.823,1.198 1.135,1.563 0.313,0.365 10 false E 0.448,1.198 0.76,1.563 0.313,0.365 10 false F 0.396,2.406 0.76,2.875 0.365,0.469 10 false F7 0.813,3 1.427,3.219 0.615,0.219 10 false PAON 1.583,3 2.198,3.219 0.615,0.219 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag ECU Assembly
*3 Combination Meter Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F7-3 (PAON) - Body ground Always 1 MΩ or higher
F7-4 (P-AB) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

NG

9.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
9.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
C285472C03
1.646,0.198 1.979,0.448 0.333,0.25 1.125,1.583 1.896,0.833 false 2.333,1.583 2.469,0.979 false 1.969,3.188 1.969,2.438 false 1.969,2.75 1.635,2.75 false 3,1.583 2.573,1.115 false 1.708,1.573 1.823,1.104 false 0.208,2.375 0.625,2.708 0.417,0.333 10 false *1 3,2.385 3.25,2.813 0.25,0.427 10 false *2 0.208,2.979 0.542,3.25 0.333,0.271 10 false *3 1.906,3.208 2.156,3.406 0.25,0.198 10 false *4 0.156,0.198 0.573,0.49 0.417,0.292 10 false *a 1.729,0.25 2.146,0.583 0.417,0.333 10 false 3A 0.927,1.583 1.344,1.833 0.417,0.25 10 false PAON 2.146,1.583 2.563,1.917 0.417,0.333 10 false PAON 2.708,2.375 2.958,2.802 0.25,0.427 10 false A 2.333,2.375 2.583,2.802 0.25,0.427 10 false B 0.823,2.375 1.073,2.802 0.25,0.427 10 false C 0.458,2.375 0.708,2.802 0.25,0.427 10 false D 0.823,2.969 1.073,3.396 0.25,0.427 10 false E 0.458,2.969 0.708,3.396 0.25,0.427 10 false F 2.854,1.583 3.271,1.833 0.417,0.25 10 false P-AB 1.552,1.583 1.969,1.917 0.417,0.333 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag ECU Assembly
*3 Combination Meter Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the connector from the instrument panel junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-8 (PAON) - Body ground Always 1 MΩ or higher
3A-29 (PAON) - Body ground Always 1 MΩ or higher
3A-46 (P-AB) - Body ground Always 1 MΩ or higher
3A-51 (P-AB) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

10.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
C285472C03
1.646,0.198 1.979,0.448 0.333,0.25 1.125,1.583 1.896,0.833 false 2.333,1.583 2.469,0.979 false 1.969,3.188 1.969,2.438 false 1.969,2.75 1.635,2.75 false 3,1.583 2.573,1.115 false 1.708,1.573 1.823,1.104 false 0.208,2.375 0.625,2.708 0.417,0.333 10 false *1 3,2.385 3.25,2.813 0.25,0.427 10 false *2 0.208,2.979 0.542,3.25 0.333,0.271 10 false *3 1.906,3.208 2.156,3.406 0.25,0.198 10 false *4 0.156,0.198 0.573,0.49 0.417,0.292 10 false *a 1.729,0.25 2.146,0.583 0.417,0.333 10 false 3A 0.927,1.583 1.344,1.833 0.417,0.25 10 false PAON 2.146,1.583 2.563,1.917 0.417,0.333 10 false PAON 2.708,2.375 2.958,2.802 0.25,0.427 10 false A 2.333,2.375 2.583,2.802 0.25,0.427 10 false B 0.823,2.375 1.073,2.802 0.25,0.427 10 false C 0.458,2.375 0.708,2.802 0.25,0.427 10 false D 0.823,2.969 1.073,3.396 0.25,0.427 10 false E 0.458,2.969 0.708,3.396 0.25,0.427 10 false F 2.854,1.583 3.271,1.833 0.417,0.25 10 false P-AB 1.552,1.583 1.969,1.917 0.417,0.333 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag ECU Assembly
*3 Combination Meter Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the connector from the instrument panel junction block assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3A-8 (PAON) - Body ground Power switch on (IG) Below 1 V
3A-29 (PAON) - Body ground Power switch on (IG) Below 1 V
3A-46 (P-AB) - Body ground Power switch on (IG) Below 1 V
3A-51 (P-AB) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

11.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
C285472C03
1.646,0.198 1.979,0.448 0.333,0.25 1.125,1.583 1.896,0.833 false 2.333,1.583 2.469,0.979 false 1.969,3.188 1.969,2.438 false 1.969,2.75 1.635,2.75 false 3,1.583 2.573,1.115 false 1.708,1.573 1.823,1.104 false 0.208,2.375 0.625,2.708 0.417,0.333 10 false *1 3,2.385 3.25,2.813 0.25,0.427 10 false *2 0.208,2.979 0.542,3.25 0.333,0.271 10 false *3 1.906,3.208 2.156,3.406 0.25,0.198 10 false *4 0.156,0.198 0.573,0.49 0.417,0.292 10 false *a 1.729,0.25 2.146,0.583 0.417,0.333 10 false 3A 0.927,1.583 1.344,1.833 0.417,0.25 10 false PAON 2.146,1.583 2.563,1.917 0.417,0.333 10 false PAON 2.708,2.375 2.958,2.802 0.25,0.427 10 false A 2.333,2.375 2.583,2.802 0.25,0.427 10 false B 0.823,2.375 1.073,2.802 0.25,0.427 10 false C 0.458,2.375 0.708,2.802 0.25,0.427 10 false D 0.823,2.969 1.073,3.396 0.25,0.427 10 false E 0.458,2.969 0.708,3.396 0.25,0.427 10 false F 2.854,1.583 3.271,1.833 0.417,0.25 10 false P-AB 1.552,1.583 1.969,1.917 0.417,0.333 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag ECU Assembly
*3 Combination Meter Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the connector from the instrument panel junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-8 (PAON) - 3A-46 (P-AB) Always 1 MΩ or higher
3A-29 (PAON) - 3A-51 (P-AB) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

12.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
C285471C04
1.635,0.146 1.969,0.365 0.333,0.219 1.083,3.479 1.406,3.698 0.323,0.219 1.5,1.417 1.813,1.031 false 2.333,1.417 1.896,0.75 false 1.75,4.25 2.063,3.844 false 3,4.25 2.521,3.604 false 2.333,4.417 2.333,4.208 false 1.958,2.833 1.958,2.25 false 1.958,2.5 1.625,2.5 false 0.198,2.198 0.594,2.521 0.396,0.323 10 false *1 3,2.208 3.333,2.615 0.333,0.406 10 false *2 0.219,2.792 0.615,3.125 0.396,0.333 10 false *3 1.896,2.844 2.208,3.125 0.313,0.281 10 false *4 2.281,4.427 2.51,4.667 0.229,0.24 10 false *5 0.135,0.115 0.469,0.438 0.333,0.323 10 false *a 0.938,3.156 1.333,3.823 0.396,0.667 10 false *b 2.708,2.198 3.042,2.604 0.333,0.406 10 false A 2.323,2.188 2.656,2.594 0.333,0.406 10 false B 0.823,2.188 1.156,2.594 0.333,0.406 10 false C 0.448,2.198 0.781,2.604 0.333,0.406 10 false D 0.823,2.792 1.156,3.198 0.333,0.406 10 false E 0.448,2.792 0.781,3.198 0.333,0.406 10 false F 1.729,0.177 2.063,0.583 0.333,0.406 10 false 3A 1.302,1.417 1.802,1.833 0.5,0.417 10 false P-AB 2.156,1.417 2.708,1.802 0.552,0.385 10 false PAON 1.521,4.25 2.021,4.667 0.5,0.417 10 false PAON 2.854,4.25 3.271,4.5 0.417,0.25 10 false P-AB 1.135,3.51 1.469,3.917 0.333,0.406 10 false F56
*1 Instrument Panel Junction Block Assembly
*2 Airbag ECU Assembly
*3 Combination Meter Assembly
*4 Instrument Panel Wire
*5 Service Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Disconnect the connector from the instrument panel junction block assembly.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-8 (PAON) - 3A-46 (P-AB) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


d.
C348694C01
0.604,3.646 0.969,3.875 0.365,0.229 1.531,0.125 1.885,0.354 0.354,0.229 1.979,2.594 1.625,2.594 false 1.979,2.927 1.979,2.26 false 1.667,4.448 1.667,4.281 false 1.042,4.25 1.594,3.792 false 2.198,4.25 1.75,3.792 false 2.125,1.458 2.458,0.896 false 2.865,1.458 2.573,1.021 false 0.156,2.188 0.552,2.542 0.396,0.354 10 false *1 3,2.198 3.375,2.531 0.375,0.333 10 false *2 0.177,2.792 0.521,3.021 0.344,0.229 10 false *3 1.917,2.948 2.26,3.198 0.344,0.25 10 false *4 1.604,4.458 1.917,4.667 0.313,0.208 10 false *5 0.135,0.125 0.49,0.406 0.354,0.281 10 false *a 0.5,3.281 0.896,3.802 0.396,0.521 10 false *b 2.698,2.198 3.073,2.531 0.375,0.333 10 false A 2.323,2.198 2.698,2.531 0.375,0.333 10 false B 0.823,2.198 1.198,2.531 0.375,0.333 10 false C 0.438,2.198 0.813,2.531 0.375,0.333 10 false D 0.813,2.792 1.188,3.125 0.375,0.333 10 false E 0.438,2.792 0.813,3.125 0.375,0.333 10 false F 0.854,4.25 1.417,4.5 0.563,0.25 10 false PAON 2.052,4.25 2.615,4.5 0.563,0.25 10 false P-AB 1.938,1.469 2.5,1.719 0.563,0.25 10 false PAON 2.708,1.469 3.271,1.719 0.563,0.25 10 false P-AB 1.625,0.156 2.188,0.406 0.563,0.25 10 false 3A 0.719,3.688 1.281,3.938 0.563,0.25 10 false F7
*1 Instrument Panel Junction Block Assembly
*2 Airbag ECU Assembly
*3 Combination Meter Assembly
*4 Instrument Panel Wire
*5 Service Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)
*b Front view of wire harness connector
(to Combination Meter Assembly)


Using a service wire, connect terminals 3 (PAON) and 4 (P-AB) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-29 (PAON) - 3A-51 (P-AB) Always Below 1 Ω



f.

Disconnect the service wire from connector E.


Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

13.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly, combination meter assembly and instrument panel junction block assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly, combination meter assembly and instrument panel junction block assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

14.CHECK WIRE HARNESS (OPEN)

NG

REPLACE INSTRUMENT PANEL WIRE

14.CHECK WIRE HARNESS (OPEN)
a.
C348692C01
0.292,0.438 0.646,0.677 0.354,0.24 0.271,3.729 0.604,3.948 0.333,0.219 1.542,1.417 1.542,1.167 false 0.979,1.229 1.281,0.833 false 2.125,1.24 1.729,0.594 false 1,4.333 1.281,3.792 false 1.698,4.313 1.427,3.792 false 2.01,2.813 2.01,2.063 false 2.01,2.417 1.625,2.417 false 0.167,1.979 0.552,2.292 0.385,0.313 10 false *1 3,2 3.354,2.385 0.354,0.385 10 false *2 0.177,2.677 0.604,3.063 0.427,0.385 10 false *3 1.948,2.833 2.344,3.229 0.396,0.396 10 false *4 1.479,1.427 1.833,1.802 0.354,0.375 10 false *5 0.135,0.146 0.51,0.5 0.375,0.354 10 false *a 0.146,3.281 0.521,3.854 0.375,0.573 10 false *b 0.771,1.25 1.375,1.625 0.604,0.375 10 false PAON 1.979,1.25 2.583,1.625 0.604,0.375 10 false P-AB 0.354,0.479 0.958,0.854 0.604,0.375 10 false F56 0.365,3.76 0.969,4.135 0.604,0.375 10 false F7 2.698,2 3.135,2.427 0.438,0.427 10 false A 2.323,2 2.76,2.427 0.438,0.427 10 false B 0.625,2 1.063,2.427 0.438,0.427 10 false C 0.438,2 0.875,2.427 0.438,0.427 10 false D 0.823,2.677 1.26,3.104 0.438,0.427 10 false E 0.448,2.677 0.885,3.104 0.438,0.427 10 false F 1.542,4.333 2.063,4.594 0.521,0.26 10 false P-AB 0.802,4.333 1.302,4.542 0.5,0.208 10 false PAON
*1 Instrument Panel Junction Block Assembly
*2 Airbag ECU Assembly
*3 Combination Meter Assembly
*4 Instrument Panel Wire
*5 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Combination Meter Assembly)


Connect the connector to the instrument panel junction block assembly.


b.

Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F7-3 (PAON) - F7-4 (P-AB) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

15.CHECK WIRE HARNESS (SHORT)

NG

24.CHECK INSTRUMENT PANEL WIRE (OPEN)
15.CHECK WIRE HARNESS (SHORT)
a.
C348693C01
0.313,2.375 0.615,2.594 0.302,0.219 1.958,1.333 1.958,0.583 false 1.958,0.958 1.635,0.958 false 1,3 1.302,2.438 false 1.74,3 1.458,2.438 false 3,0.521 3.313,0.885 0.313,0.365 10 false *2 0.188,0.51 0.583,0.75 0.396,0.24 10 false *1 0.198,1.198 0.573,1.406 0.375,0.208 10 false *3 1.896,1.354 2.25,1.573 0.354,0.219 10 false *4 0.167,1.854 0.531,2.323 0.365,0.469 10 false *a 2.698,0.521 3.01,0.885 0.313,0.365 10 false A 2.323,0.521 2.635,0.885 0.313,0.365 10 false B 0.635,0.521 0.948,0.885 0.313,0.365 10 false C 0.448,0.521 0.76,0.885 0.313,0.365 10 false D 0.823,1.198 1.135,1.563 0.313,0.365 10 false E 0.448,1.198 0.76,1.563 0.313,0.365 10 false F 0.396,2.406 0.76,2.875 0.365,0.469 10 false F7 0.813,3 1.427,3.219 0.615,0.219 10 false PAON 1.583,3 2.198,3.219 0.615,0.219 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag ECU Assembly
*3 Combination Meter Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F7-3 (PAON) - F7-4 (P-AB) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

16.CHECK WIRE HARNESS (SHORT TO B+)

NG

23.CHECK INSTRUMENT PANEL WIRE (SHORT)
16.CHECK WIRE HARNESS (SHORT TO B+)
a.
C348693C01
0.313,2.375 0.615,2.594 0.302,0.219 1.958,1.333 1.958,0.583 false 1.958,0.958 1.635,0.958 false 1,3 1.302,2.438 false 1.74,3 1.458,2.438 false 3,0.521 3.313,0.885 0.313,0.365 10 false *2 0.188,0.51 0.583,0.75 0.396,0.24 10 false *1 0.198,1.198 0.573,1.406 0.375,0.208 10 false *3 1.896,1.354 2.25,1.573 0.354,0.219 10 false *4 0.167,1.854 0.531,2.323 0.365,0.469 10 false *a 2.698,0.521 3.01,0.885 0.313,0.365 10 false A 2.323,0.521 2.635,0.885 0.313,0.365 10 false B 0.635,0.521 0.948,0.885 0.313,0.365 10 false C 0.448,0.521 0.76,0.885 0.313,0.365 10 false D 0.823,1.198 1.135,1.563 0.313,0.365 10 false E 0.448,1.198 0.76,1.563 0.313,0.365 10 false F 0.396,2.406 0.76,2.875 0.365,0.469 10 false F7 0.813,3 1.427,3.219 0.615,0.219 10 false PAON 1.583,3 2.198,3.219 0.615,0.219 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag ECU Assembly
*3 Combination Meter Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Combination Meter Assembly)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F7-3 (PAON) - Body ground Power switch on (IG) Below 1 V
F7-4 (P-AB) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

17.CHECK WIRE HARNESS (SHORT TO GROUND)

NG

22.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
17.CHECK WIRE HARNESS (SHORT TO GROUND)
a.
C348693C01
0.313,2.375 0.615,2.594 0.302,0.219 1.958,1.333 1.958,0.583 false 1.958,0.958 1.635,0.958 false 1,3 1.302,2.438 false 1.74,3 1.458,2.438 false 3,0.521 3.313,0.885 0.313,0.365 10 false *2 0.188,0.51 0.583,0.75 0.396,0.24 10 false *1 0.198,1.198 0.573,1.406 0.375,0.208 10 false *3 1.896,1.354 2.25,1.573 0.354,0.219 10 false *4 0.167,1.854 0.531,2.323 0.365,0.469 10 false *a 2.698,0.521 3.01,0.885 0.313,0.365 10 false A 2.323,0.521 2.635,0.885 0.313,0.365 10 false B 0.635,0.521 0.948,0.885 0.313,0.365 10 false C 0.448,0.521 0.76,0.885 0.313,0.365 10 false D 0.823,1.198 1.135,1.563 0.313,0.365 10 false E 0.448,1.198 0.76,1.563 0.313,0.365 10 false F 0.396,2.406 0.76,2.875 0.365,0.469 10 false F7 0.813,3 1.427,3.219 0.615,0.219 10 false PAON 1.583,3 2.198,3.219 0.615,0.219 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag ECU Assembly
*3 Combination Meter Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F7-3 (PAON) - Body ground Always 1 MΩ or higher
F7-4 (P-AB) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

18.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (SOURCE VOLTAGE)

NG

21.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
18.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (SOURCE VOLTAGE)
a.
C350250C01
0.26,2.115 0.594,2.323 0.333,0.208 0.479,2.885 0.823,2.615 false 1.958,1.417 1.958,0.583 false 1.958,0.969 1.625,0.969 false 0.177,0.521 0.615,0.833 0.438,0.313 10 false *1 2.979,0.521 3.323,0.844 0.344,0.323 10 false *2 0.188,1.198 0.604,1.458 0.417,0.26 10 false *3 1.896,1.438 2.26,1.677 0.365,0.24 10 false *4 0.167,1.865 0.531,2.313 0.365,0.448 10 false *a 2.698,0.521 3.042,0.844 0.344,0.323 10 false A 2.323,0.521 2.667,0.844 0.344,0.323 10 false B 0.625,0.521 0.969,0.844 0.344,0.323 10 false C 0.438,0.521 0.781,0.844 0.344,0.323 10 false D 0.823,1.208 1.167,1.531 0.344,0.323 10 false E 0.438,1.208 0.781,1.531 0.344,0.323 10 false F 0.365,2.896 0.729,3.344 0.365,0.448 10 false IG+ 0.344,2.135 0.708,2.583 0.365,0.448 10 false F6
*1 Instrument Panel Junction Block Assembly
*2 Airbag ECU Assembly
*3 Combination Meter Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Combination Meter Assembly)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F6-21 (IG+) - Body ground Power switch on (IG) 11 to 14 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

19.CHECK PASSENGER AIRBAG ON/OFF INDICATOR

NG

REPLACE WIRE HARNESS OR AUXILIARY BATTERY

19.CHECK PASSENGER AIRBAG ON/OFF INDICATOR
a.
C285470C05
1.073,2.302 1.406,2.521 0.333,0.219 1.781,1.438 1.781,0.604 false 1.771,0.917 1.521,0.917 false 1.833,3.083 2.021,2.688 false 2.75,3.083 2.49,2.427 false 0.292,0.531 0.604,0.865 0.313,0.333 10 false *1 2.896,0.542 3.292,1.031 0.396,0.49 10 false *2 0.302,1.208 0.615,1.531 0.313,0.323 10 false *3 1.719,1.458 2.031,1.875 0.313,0.417 10 false *4 0.917,1.844 1.229,2.26 0.313,0.417 10 false *a 2.604,0.531 3,1.021 0.396,0.49 10 false A 2.229,0.531 2.625,1.021 0.396,0.49 10 false B 0.719,0.531 1.115,1.021 0.396,0.49 10 false C 0.531,0.531 0.927,1.021 0.396,0.49 10 false D 0.719,1.219 1.115,1.708 0.396,0.49 10 false E 0.542,1.208 0.938,1.698 0.396,0.49 10 false F 1.125,2.333 1.521,2.823 0.396,0.49 10 false F56 1.646,3.083 2.146,3.333 0.5,0.25 10 false PAON 2.615,3.083 3.115,3.333 0.5,0.25 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag ECU Assembly
*3 Combination Meter Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)


Connect the connector to the combination meter assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Check the passenger airbag ON/OFF indicator according to the conditions in the table below.

OK:
Terminal Connection Condition Specified Condition
F56-23 (PAON) - Body ground Power switch on (IG) "ON" comes on
F56-17 (P-AB) - Body ground Power switch on (IG) "OFF" comes on



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

20.CHECK DTC

NG

20.CHECK DTC
a.
C284134C01
0.271,0.802 0.583,1.073 0.313,0.271 10 false *1 2.906,0.813 3.219,1.104 0.313,0.292 10 false *2 0.292,1.469 0.719,1.917 0.427,0.448 10 false *3 2.615,0.802 2.927,1.146 0.313,0.344 10 false A 2.427,0.802 2.74,1.198 0.313,0.396 10 false B 0.74,0.802 1.042,1.177 0.302,0.375 10 false C 0.552,0.802 0.865,1.094 0.313,0.292 10 false D 0.729,1.479 1.083,1.979 0.354,0.5 10 false E 0.563,1.479 0.875,1.635 0.313,0.156 10 false F
*1 Instrument Panel Junction Block Assembly
*2 Airbag ECU Assembly
*3 Combination Meter Assembly


Connect the connector to the airbag ECU assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1660/43 is not output.


HINT:

Codes other than DTC B1660/43 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG

21.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
C285472C03
1.646,0.198 1.979,0.448 0.333,0.25 1.125,1.583 1.896,0.833 false 2.333,1.583 2.469,0.979 false 1.969,3.188 1.969,2.438 false 1.969,2.75 1.635,2.75 false 3,1.583 2.573,1.115 false 1.708,1.573 1.823,1.104 false 0.208,2.375 0.625,2.708 0.417,0.333 10 false *1 3,2.385 3.25,2.813 0.25,0.427 10 false *2 0.208,2.979 0.542,3.25 0.333,0.271 10 false *3 1.906,3.208 2.156,3.406 0.25,0.198 10 false *4 0.156,0.198 0.573,0.49 0.417,0.292 10 false *a 1.729,0.25 2.146,0.583 0.417,0.333 10 false 3A 0.927,1.583 1.344,1.833 0.417,0.25 10 false PAON 2.146,1.583 2.563,1.917 0.417,0.333 10 false PAON 2.708,2.375 2.958,2.802 0.25,0.427 10 false A 2.333,2.375 2.583,2.802 0.25,0.427 10 false B 0.823,2.375 1.073,2.802 0.25,0.427 10 false C 0.458,2.375 0.708,2.802 0.25,0.427 10 false D 0.823,2.969 1.073,3.396 0.25,0.427 10 false E 0.458,2.969 0.708,3.396 0.25,0.427 10 false F 2.854,1.583 3.271,1.833 0.417,0.25 10 false P-AB 1.552,1.583 1.969,1.917 0.417,0.333 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag ECU Assembly
*3 Combination Meter Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the connector from the instrument panel junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-8 (PAON) - Body ground Always 1 MΩ or higher
3A-29 (PAON) - Body ground Always 1 MΩ or higher
3A-46 (P-AB) - Body ground Always 1 MΩ or higher
3A-51 (P-AB) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

22.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
C285472C03
1.646,0.198 1.979,0.448 0.333,0.25 1.125,1.583 1.896,0.833 false 2.333,1.583 2.469,0.979 false 1.969,3.188 1.969,2.438 false 1.969,2.75 1.635,2.75 false 3,1.583 2.573,1.115 false 1.708,1.573 1.823,1.104 false 0.208,2.375 0.625,2.708 0.417,0.333 10 false *1 3,2.385 3.25,2.813 0.25,0.427 10 false *2 0.208,2.979 0.542,3.25 0.333,0.271 10 false *3 1.906,3.208 2.156,3.406 0.25,0.198 10 false *4 0.156,0.198 0.573,0.49 0.417,0.292 10 false *a 1.729,0.25 2.146,0.583 0.417,0.333 10 false 3A 0.927,1.583 1.344,1.833 0.417,0.25 10 false PAON 2.146,1.583 2.563,1.917 0.417,0.333 10 false PAON 2.708,2.375 2.958,2.802 0.25,0.427 10 false A 2.333,2.375 2.583,2.802 0.25,0.427 10 false B 0.823,2.375 1.073,2.802 0.25,0.427 10 false C 0.458,2.375 0.708,2.802 0.25,0.427 10 false D 0.823,2.969 1.073,3.396 0.25,0.427 10 false E 0.458,2.969 0.708,3.396 0.25,0.427 10 false F 2.854,1.583 3.271,1.833 0.417,0.25 10 false P-AB 1.552,1.583 1.969,1.917 0.417,0.333 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag ECU Assembly
*3 Combination Meter Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the connector from the instrument panel junction block assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3A-8 (PAON) - Body ground Power switch on (IG) Below 1 V
3A-29 (PAON) - Body ground Power switch on (IG) Below 1 V
3A-46 (P-AB) - Body ground Power switch on (IG) Below 1 V
3A-51 (P-AB) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

23.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
C285472C03
1.646,0.198 1.979,0.448 0.333,0.25 1.125,1.583 1.896,0.833 false 2.333,1.583 2.469,0.979 false 1.969,3.188 1.969,2.438 false 1.969,2.75 1.635,2.75 false 3,1.583 2.573,1.115 false 1.708,1.573 1.823,1.104 false 0.208,2.375 0.625,2.708 0.417,0.333 10 false *1 3,2.385 3.25,2.813 0.25,0.427 10 false *2 0.208,2.979 0.542,3.25 0.333,0.271 10 false *3 1.906,3.208 2.156,3.406 0.25,0.198 10 false *4 0.156,0.198 0.573,0.49 0.417,0.292 10 false *a 1.729,0.25 2.146,0.583 0.417,0.333 10 false 3A 0.927,1.583 1.344,1.833 0.417,0.25 10 false PAON 2.146,1.583 2.563,1.917 0.417,0.333 10 false PAON 2.708,2.375 2.958,2.802 0.25,0.427 10 false A 2.333,2.375 2.583,2.802 0.25,0.427 10 false B 0.823,2.375 1.073,2.802 0.25,0.427 10 false C 0.458,2.375 0.708,2.802 0.25,0.427 10 false D 0.823,2.969 1.073,3.396 0.25,0.427 10 false E 0.458,2.969 0.708,3.396 0.25,0.427 10 false F 2.854,1.583 3.271,1.833 0.417,0.25 10 false P-AB 1.552,1.583 1.969,1.917 0.417,0.333 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag ECU Assembly
*3 Combination Meter Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the connector from the instrument panel junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-8 (PAON) - 3A-46 (P-AB) Always 1 MΩ or higher
3A-29 (PAON) - 3A-51 (P-AB) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

24.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
C285471C04
1.635,0.146 1.969,0.365 0.333,0.219 1.083,3.479 1.406,3.698 0.323,0.219 1.5,1.417 1.813,1.031 false 2.333,1.417 1.896,0.75 false 1.75,4.25 2.063,3.844 false 3,4.25 2.521,3.604 false 2.333,4.417 2.333,4.208 false 1.958,2.833 1.958,2.25 false 1.958,2.5 1.625,2.5 false 0.198,2.198 0.594,2.521 0.396,0.323 10 false *1 3,2.208 3.333,2.615 0.333,0.406 10 false *2 0.219,2.792 0.615,3.125 0.396,0.333 10 false *3 1.896,2.844 2.208,3.125 0.313,0.281 10 false *4 2.281,4.427 2.51,4.667 0.229,0.24 10 false *5 0.135,0.115 0.469,0.438 0.333,0.323 10 false *a 0.938,3.156 1.333,3.823 0.396,0.667 10 false *b 2.708,2.198 3.042,2.604 0.333,0.406 10 false A 2.323,2.188 2.656,2.594 0.333,0.406 10 false B 0.823,2.188 1.156,2.594 0.333,0.406 10 false C 0.448,2.198 0.781,2.604 0.333,0.406 10 false D 0.823,2.792 1.156,3.198 0.333,0.406 10 false E 0.448,2.792 0.781,3.198 0.333,0.406 10 false F 1.729,0.177 2.063,0.583 0.333,0.406 10 false 3A 1.302,1.417 1.802,1.833 0.5,0.417 10 false P-AB 2.156,1.417 2.708,1.802 0.552,0.385 10 false PAON 1.521,4.25 2.021,4.667 0.5,0.417 10 false PAON 2.854,4.25 3.271,4.5 0.417,0.25 10 false P-AB 1.135,3.51 1.469,3.917 0.333,0.406 10 false F56
*1 Instrument Panel Junction Block Assembly
*2 Airbag ECU Assembly
*3 Combination Meter Assembly
*4 Instrument Panel Wire
*5 Service Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Disconnect the connector from the instrument panel junction block assembly.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-8 (PAON) - 3A-46 (P-AB) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


d.
C348694C01
0.604,3.646 0.969,3.875 0.365,0.229 1.531,0.125 1.885,0.354 0.354,0.229 1.979,2.594 1.625,2.594 false 1.979,2.927 1.979,2.26 false 1.667,4.448 1.667,4.281 false 1.042,4.25 1.594,3.792 false 2.198,4.25 1.75,3.792 false 2.125,1.458 2.458,0.896 false 2.865,1.458 2.573,1.021 false 0.156,2.188 0.552,2.542 0.396,0.354 10 false *1 3,2.198 3.375,2.531 0.375,0.333 10 false *2 0.177,2.792 0.521,3.021 0.344,0.229 10 false *3 1.917,2.948 2.26,3.198 0.344,0.25 10 false *4 1.604,4.458 1.917,4.667 0.313,0.208 10 false *5 0.135,0.125 0.49,0.406 0.354,0.281 10 false *a 0.5,3.281 0.896,3.802 0.396,0.521 10 false *b 2.698,2.198 3.073,2.531 0.375,0.333 10 false A 2.323,2.198 2.698,2.531 0.375,0.333 10 false B 0.823,2.198 1.198,2.531 0.375,0.333 10 false C 0.438,2.198 0.813,2.531 0.375,0.333 10 false D 0.813,2.792 1.188,3.125 0.375,0.333 10 false E 0.438,2.792 0.813,3.125 0.375,0.333 10 false F 0.854,4.25 1.417,4.5 0.563,0.25 10 false PAON 2.052,4.25 2.615,4.5 0.563,0.25 10 false P-AB 1.938,1.469 2.5,1.719 0.563,0.25 10 false PAON 2.708,1.469 3.271,1.719 0.563,0.25 10 false P-AB 1.625,0.156 2.188,0.406 0.563,0.25 10 false 3A 0.719,3.688 1.281,3.938 0.563,0.25 10 false F7
*1 Instrument Panel Junction Block Assembly
*2 Airbag ECU Assembly
*3 Combination Meter Assembly
*4 Instrument Panel Wire
*5 Service Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)
*b Front view of wire harness connector
(to Combination Meter Assembly)


Using a service wire, connect terminals 3 (PAON) and 4 (P-AB) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-29 (PAON) - 3A-51 (P-AB) Always Below 1 Ω



f.

Disconnect the service wire from connector E.


Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE