Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0225220 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1805/52  Short in Front Passenger Side Squib Circuit  B1806/52  Open in Front Passenger Side Squib Circuit  B1807/52  Short to GND in Front Passenger Side Squib Circuit  B1808/52  Short to B+ in Front Passenger Side Squib Circuit  


DESCRIPTION

The front passenger side squib circuit consists of the airbag ECU assembly and instrument panel passenger airbag assembly.

The airbag ECU assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front passenger side squib circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1805/52 Short in Front Passenger Side Squib Circuit
·

The airbag ECU assembly detects a line short in the front passenger side squib circuit during the primary check.

·

Front passenger side squib malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Front passenger side squib (Instrument panel passenger airbag assembly)

·

Airbag ECU assembly


Applies to check mode
B1806/52 Open in Front Passenger Side Squib Circuit
·

The airbag ECU assembly detects an open in the front passenger side squib circuit.

·

Front passenger side squib malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Front passenger side squib (Instrument panel passenger airbag assembly)

·

Airbag ECU assembly


Applies to check mode
B1807/52 Short to GND in Front Passenger Side Squib Circuit
·

The airbag ECU assembly detects a short to ground in the front passenger side squib circuit.

·

Front passenger side squib malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Front passenger side squib (Instrument panel passenger airbag assembly)

·

Airbag ECU assembly


Applies to check mode
B1808/52 Short to B+ in Front Passenger Side Squib Circuit
·

The airbag ECU assembly detects a short to B+ in the front passenger side squib circuit.

·

Front passenger side squib malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Front passenger side squib (Instrument panel passenger airbag assembly)

·

Airbag ECU assembly


Applies to check mode

WIRING DIAGRAM

C350252E01
4.635,2.458 6.354,3.146 1.719,0.688 10 false F56 4.635,2.625 6.354,3.313 1.719,0.688 10 false Airbag ECU Assembly 4.688,0.885 6.406,1.573 1.719,0.688 10 false P+ 4.688,1.74 5.677,2.135 0.99,0.396 10 false P- 4.521,0.792 6.24,1.479 1.719,0.688 10 false 4 4.521,1.615 5.156,2.063 0.635,0.448 10 false 3 3.448,0.698 5.167,1.385 1.719,0.688 10 false 1 3.448,1.531 5.167,2.219 1.719,0.688 10 false 2 3.104,0.885 4.823,1.573 1.719,0.688 10 false FX2*1, FX1*2 3.104,1.719 4.823,2.406 1.719,0.688 10 false FX2*1, FX1*2 0.708,2.229 2.427,2.917 1.719,0.688 10 false X1 0.708,2.396 3.219,2.833 2.51,0.438 10 false Front Passenger Side Squib (Instrument Panel Passenger Airbag Assembly) 2.135,0.781 3.854,1.469 1.719,0.688 10 false P+ 2.156,1.615 3.146,2.01 0.99,0.396 10 false P- 2.406,0.781 4.125,1.469 1.719,0.688 10 false 1 2.406,1.615 3.396,2.01 0.99,0.396 10 false 2 0.188,3.49 3.188,3.802 3,0.313 10 false *2: w/ Passenger Airbag ON/OFF Indicator 0.188,3.167 3.188,3.479 3,0.313 10 false *1: w/o Passenger Airbag ON/OFF Indicator

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/o Passenger Airbag ON/OFF Indicator A
w/ Passenger Airbag ON/OFF Indicator B



A

2.CHECK CONNECTORS

B

8.CHECK CONNECTORS
2.CHECK CONNECTORS
a.
C241746C01
0.271,0.99 0.271,1.427 false 1.76,1 1.76,1.438 false 0.979,0.875 0.979,0.5 0.979,0.5 0.823,0.5 false 0.198,1.448 0.573,1.781 0.375,0.333 10 *1 0.667,0.427 1.146,0.708 0.479,0.281 10 *3 2.708,1.188 3,1.5 0.292,0.313 10 *2 2.25,0.854 2.5,1.25 0.25,0.396 10 A 1.948,0.854 2.219,1.156 0.271,0.302 10 B 1.479,0.854 1.76,1.115 0.281,0.26 10 C 1.167,0.854 1.49,1.135 0.323,0.281 10 D 0.688,0.854 0.896,1.177 0.208,0.323 10 E 0.396,0.854 0.635,1.146 0.24,0.292 10 F 1.698,1.448 1.958,1.74 0.26,0.292 10 *4
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag ECU Assembly
*3 No. 2 Instrument Panel Wire
*4 Instrument Panel Wire


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the instrument panel passenger airbag assembly and airbag ECU assembly. Also check that the connectors that link the instrument panel wire and No. 2 instrument panel wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the instrument panel passenger airbag assembly and airbag ECU assembly. Also disconnect the instrument panel wire from the No. 2 instrument panel wire.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the No. 2 instrument panel wire connector (on the instrument panel passenger airbag assembly side) is not loose, deformed or damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short springs of the activation prevention mechanisms of the instrument panel wire connector and No. 2 instrument panel wire connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

NG

REPLACE WIRE HARNESS

3.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY
a.
C241747C07
0.385,2.385 0.708,2.604 0.323,0.219 0.385,0.667 0.385,0.927 false 1.75,2.281 2.031,2.281 false 0.323,0.948 0.771,1.26 0.448,0.313 10 false *1 0.333,1.698 0.719,2.063 0.385,0.365 10 false *a 2.063,2.208 2.417,2.531 0.354,0.323 10 false SST 2.594,0.833 2.969,1.135 0.375,0.302 10 false *2 2.177,0.531 2.375,0.74 0.198,0.208 10 false A 2.021,0.531 2.198,0.844 0.177,0.313 10 false B 1.531,0.531 1.813,0.771 0.281,0.24 10 false C 1.375,0.521 1.677,0.885 0.302,0.365 10 false D 0.896,0.521 1.177,0.927 0.281,0.406 10 false E 0.5,0.521 0.844,0.813 0.344,0.292 10 false F 0.49,2.417 0.865,2.719 0.375,0.302 10 false X1
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly)


Connect the instrument panel wire to the No. 2 instrument panel wire and airbag ECU assembly.


b.

Connect SST (resistance 2.1 Ω) to connector E.

CAUTION:

Never connect a tester to the instrument panel passenger airbag assembly for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output.


HINT:

Codes other than DTCs B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Disconnect SST from connector E.


Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

NG

4.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT
4.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT
a.
C238254C15
0.688,2.292 1.021,2.531 0.333,0.24 0.375,0.656 0.375,0.938 false 1.479,2.094 1.146,1.906 false 1.948,1.906 1.646,2.094 false 0.5,0.5 0.979,0.99 0.479,0.49 10 false F 0.802,0.5 1.208,1.01 0.406,0.51 10 false E 1.26,0.5 1.552,0.938 0.292,0.438 10 false D 1.406,0.5 1.688,0.885 0.281,0.385 10 false C 1.865,0.5 2.104,0.99 0.24,0.49 10 false B 2.177,0.5 2.448,0.969 0.271,0.469 10 false A 0.313,0.958 0.667,1.292 0.354,0.333 10 false *1 2.583,0.813 2.896,1.052 0.313,0.24 10 false *2 0.271,1.74 0.583,2.115 0.313,0.375 10 false *a 0.938,1.833 1.375,2.115 0.438,0.281 10 false P+ 1.979,1.833 2.271,2.094 0.292,0.26 10 false P- 0.792,2.333 1.208,2.771 0.417,0.438 10 false X1
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly)


Disconnect the instrument panel wire from the airbag ECU assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
X1-1 (P+) - Body ground Power switch on (IG) Below 1 V
X1-2 (P-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X1-1 (P+) - X1-2 (P-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X1-1 (P+) - Body ground Always 1 MΩ or higher
X1-2 (P-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X1-1 (P+) - X1-2 (P-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

5.CHECK DTC

NG

6.CHECK INSTRUMENT PANEL WIRE
5.CHECK DTC
a.
C238235C01
0.5,0.875 0.5,1.219 false 2.438,1.031 2.75,1.313 0.313,0.281 10 *2 0.427,1.24 0.854,1.573 0.427,0.333 10 *1 0.635,0.74 1.188,1.167 0.552,0.427 10 F 0.792,0.74 1.188,1.083 0.396,0.344 10 E 1.24,0.74 1.594,1.083 0.354,0.344 10 D 1.396,0.74 1.698,1.167 0.302,0.427 10 C 1.844,0.74 2.135,1.042 0.292,0.302 10 B 2,0.74 2.271,0.969 0.271,0.229 10 A
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag ECU Assembly


Connect the connectors to the instrument panel passenger airbag assembly and airbag ECU assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output.


HINT:

Codes other than DTCs B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG

6.CHECK INSTRUMENT PANEL WIRE
a.
C238255C25
0.615,2.198 0.99,2.427 0.375,0.229 1.656,2.615 1.313,2.792 false 1.813,2.615 2.146,2.792 false 0.292,0.656 0.292,0.958 false 1.771,0.51 1.771,0.219 1.771,0.219 1.635,0.219 false 0.99,0.656 0.99,0.958 false 0.427,0.51 0.771,0.865 0.344,0.354 10 false F 0.74,0.51 1.031,0.865 0.292,0.354 10 false E 1.188,0.51 1.5,0.802 0.313,0.292 10 false D 1.5,0.51 1.802,0.823 0.302,0.313 10 false C 1.938,0.51 2.208,0.844 0.271,0.333 10 false B 2.25,0.51 2.563,0.865 0.313,0.354 10 false A 2.688,0.813 3.146,1.104 0.458,0.292 10 false *2 0.375,1.76 0.76,2.073 0.385,0.313 10 false *a 1.104,2.729 1.531,3.052 0.427,0.323 10 false P+ 0.698,2.229 1.125,2.531 0.427,0.302 10 false FX2 2.188,2.729 2.594,3.042 0.406,0.313 10 false P- 0.208,0.969 0.656,1.365 0.448,0.396 10 false *1 0.906,0.969 1.302,1.26 0.396,0.292 10 false *3 1.479,0.146 1.854,0.448 0.375,0.302 10 false *4
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag ECU Assembly
*3 No. 2 Instrument Panel Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to No. 2 Instrument Panel Wire)


Disconnect the No. 2 instrument panel wire from the instrument panel wire.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
FX2-1 (P+) - Body ground Power switch on (IG) Below 1 V
FX2-2 (P-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FX2-1 (P+) - FX2-2 (P-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FX2-1 (P+) - Body ground Always 1 MΩ or higher
FX2-2 (P-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FX2-1 (P+) - FX2-2 (P-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

7.CHECK NO. 2 INSTRUMENT PANEL WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

7.CHECK NO. 2 INSTRUMENT PANEL WIRE
a.
C238256C11
0.76,2.219 1.094,2.448 0.333,0.229 0.281,0.656 0.281,0.938 false 1.781,0.656 1.781,0.938 false 1.479,2.104 1.125,1.906 false 1.99,1.906 1.646,2.104 false 1,0.51 1,0.208 1,0.208 1.156,0.208 false 0.427,0.51 0.688,0.844 0.26,0.333 10 false F 0.729,0.51 1.094,0.875 0.365,0.365 10 false E 1.177,0.51 1.521,0.896 0.344,0.385 10 false D 1.5,0.51 1.688,0.823 0.188,0.313 10 false C 1.948,0.51 2.219,0.854 0.271,0.344 10 false B 2.26,0.51 2.604,0.823 0.344,0.313 10 false A 0.208,0.948 0.5,1.323 0.292,0.375 10 false *1 2.656,0.802 3.021,1.177 0.365,0.375 10 false *2 0.281,1.76 0.625,2.167 0.344,0.406 10 false *a 0.917,1.833 1.25,2.104 0.333,0.271 10 false P+ 1.708,0.969 2.031,1.292 0.323,0.323 10 false *4 2.031,1.833 2.302,2.094 0.271,0.26 10 false P- 0.865,2.25 1.188,2.646 0.323,0.396 10 false X1 1.188,0.135 1.479,0.448 0.292,0.313 10 false *3
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag ECU Assembly
*3 No. 2 Instrument Panel Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly)


Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
X1-1 (P+) - Body ground Power switch on (IG) Below 1 V
X1-2 (P-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




b.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X1-1 (P+) - X1-2 (P-) Always Below 1 Ω




c.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X1-1 (P+) - Body ground Always 1 MΩ or higher
X1-2 (P-) - Body ground Always 1 MΩ or higher




d.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector D.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X1-1 (P+) - X1-2 (P-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector D to the original condition.



Result:
Proceed to
OK
NG



OK

NG

REPLACE NO. 2 INSTRUMENT PANEL WIRE

8.CHECK CONNECTORS
a.
C238337C01
0.281,1.115 0.281,1.542 false 1.76,1.115 1.76,1.542 false 0.979,0.979 0.979,0.604 0.979,0.604 0.823,0.604 false 0.219,1.563 0.563,1.781 0.344,0.219 10 *1 0.646,0.521 1.021,0.771 0.375,0.25 10 *3 2.708,0.958 3.042,1.302 0.333,0.344 10 *2 2.26,0.958 2.573,1.323 0.313,0.365 10 A 1.948,0.958 2.198,1.448 0.25,0.49 10 B 1.479,0.969 1.688,1.188 0.208,0.219 10 C 1.167,0.969 1.469,1.229 0.302,0.26 10 D 0.698,0.969 0.896,1.177 0.198,0.208 10 E 0.396,0.969 0.677,1.198 0.281,0.229 10 F 1.698,1.563 2.031,1.844 0.333,0.281 10 *4
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag ECU Assembly
*3 No. 2 Instrument Panel Wire
*4 Instrument Panel Wire


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the instrument panel passenger airbag assembly and airbag ECU assembly. Also check that the connectors that link the instrument panel wire and No. 2 instrument panel wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the instrument panel passenger airbag assembly and airbag ECU assembly. Also disconnect the instrument panel wire from the No. 2 instrument panel wire.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the No. 2 instrument panel wire connector (on the instrument panel passenger airbag assembly side) is not loose, deformed or damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short springs of the activation prevention mechanisms of the instrument panel wire connector and No. 2 instrument panel wire connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

9.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

NG

REPLACE WIRE HARNESS

9.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY
a.
C238338C11
0.396,2.333 0.729,2.552 0.333,0.219 0.385,0.844 0.385,1.104 false 1.75,2.281 2.031,2.281 false 1.5,2.708 1.781,2.708 false 0.323,1.104 0.74,1.375 0.417,0.271 10 false *1 1.813,2.635 2.125,2.927 0.313,0.292 10 false *b 0.344,1.688 0.635,2.073 0.292,0.385 10 false *a 2.073,2.198 2.479,2.531 0.406,0.333 10 false SST 2.594,0.677 2.917,1.01 0.323,0.333 10 false *2 2.177,0.677 2.479,1.031 0.302,0.354 10 false A 2.021,0.677 2.26,1.052 0.24,0.375 10 false B 1.531,0.688 1.875,0.938 0.344,0.25 10 false C 1.375,0.688 1.958,1.063 0.583,0.375 10 false D 0.896,0.688 1.438,1 0.542,0.313 10 false E 0.5,0.688 0.969,0.99 0.469,0.302 10 false F 0.5,2.365 0.854,2.74 0.354,0.375 10 false X1
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly)
*b Color: Orange


Connect the instrument panel wire to the No. 2 instrument panel wire and airbag ECU assembly.


b.

Connect SST (resistance 2.1 Ω) to connector E (orange connector).

CAUTION:

Never connect a tester to the instrument panel passenger airbag assembly for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output.


HINT:

Codes other than DTCs B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Disconnect SST from connector E.


Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

NG

10.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT
10.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT
a.
C238339C24
0.542,2.302 0.854,2.521 0.313,0.219 0.26,0.833 0.26,1.115 false 1.51,2.5 1.844,2.5 false 1.219,2.115 0.917,1.906 false 1.708,1.906 1.406,2.115 false 0.385,0.698 0.844,1.094 0.458,0.396 10 false F 0.802,0.688 1.344,1.198 0.542,0.51 10 false E 1.24,0.688 1.563,1.094 0.323,0.406 10 false D 1.396,0.688 1.792,1.313 0.396,0.625 10 false C 1.833,0.688 2.083,1.208 0.25,0.521 10 false B 2.26,0.677 2.625,1.167 0.365,0.49 10 false A 0.188,1.146 0.5,1.406 0.313,0.26 10 false *1 2.688,0.677 3.021,1 0.333,0.323 10 false *2 0.323,1.688 0.719,1.979 0.396,0.292 10 false *a 1.75,1.833 2.115,2.167 0.365,0.333 10 false P- 0.708,1.833 1.302,2.115 0.594,0.281 10 false P+ 0.635,2.333 1.167,2.719 0.531,0.385 10 false X1 1.875,2.417 2.219,2.729 0.344,0.313 10 false *b
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly)
*b Color: Orange


Disconnect the instrument panel wire from the airbag ECU assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
X1-1 (P+) - Body ground Power switch on (IG) Below 1 V
X1-2 (P-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X1-1 (P+) - X1-2 (P-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X1-1 (P+) - Body ground Always 1 MΩ or higher
X1-2 (P-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X1-1 (P+) - X1-2 (P-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

11.CHECK DTC

NG

12.CHECK INSTRUMENT PANEL WIRE
11.CHECK DTC
a.
C238340C07
0.448,1.115 0.448,1.406 false 0.573,0.969 1.698,1.51 1.125,0.542 10 false F 0.719,0.969 1.323,1.552 0.604,0.583 10 false E 1.24,0.969 2.115,1.438 0.875,0.469 10 false D 1.396,0.969 1.896,1.458 0.5,0.49 10 false C 1.917,0.969 2.438,1.427 0.521,0.458 10 false B 2.073,0.969 2.458,1.344 0.385,0.375 10 false A 0.385,1.427 0.948,1.854 0.563,0.427 10 false *1 2.49,0.979 2.823,1.385 0.333,0.406 10 false *2
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag ECU Assembly


Connect the connectors to the instrument panel passenger airbag assembly and airbag ECU assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output.


HINT:

Codes other than DTCs B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG

12.CHECK INSTRUMENT PANEL WIRE
a.
C238341C15
0.417,2.49 0.771,2.719 0.354,0.229 0.281,1.021 0.281,1.302 false 0.969,1.021 0.969,1.302 false 1.135,2.635 0.823,2.99 false 1.281,2.615 1.635,2.969 false 1.76,0.875 1.76,0.479 1.76,0.479 1.531,0.479 false 0.396,0.875 0.677,1.385 0.281,0.51 10 false F 0.677,0.875 0.948,1.177 0.271,0.302 10 false E 1.177,0.865 1.458,1.24 0.281,0.375 10 false D 1.448,0.865 1.698,1.302 0.25,0.438 10 false C 1.969,0.865 2.26,1.354 0.292,0.49 10 false B 2.24,0.865 2.563,1.438 0.323,0.573 10 false A 0.208,1.313 0.625,1.646 0.417,0.333 10 false *1 2.667,0.854 3.042,1.365 0.375,0.51 10 false *2 0.323,1.979 0.719,2.219 0.396,0.24 10 false *a 1.615,2.99 1.865,3.188 0.25,0.198 10 false P- 0.896,1.313 1.198,1.646 0.302,0.333 10 false *3 0.729,3 1.167,3.229 0.438,0.229 10 false P+ 0.49,2.521 0.802,2.865 0.313,0.344 10 false FX1 1.344,0.396 1.75,0.823 0.406,0.427 10 false *4
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag ECU Assembly
*3 No. 2 Instrument Panel Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to No. 2 Instrument Panel Wire)


Disconnect the No. 2 instrument panel wire from the instrument panel wire.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
FX1-1 (P+) - Body ground Power switch on (IG) Below 1 V
FX1-2 (P-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FX1-1 (P+) - FX1-2 (P-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FX1-1 (P+) - Body ground Always 1 MΩ or higher
FX1-2 (P-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FX1-1 (P+) - FX1-2 (P-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

13.CHECK NO. 2 INSTRUMENT PANEL WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

13.CHECK NO. 2 INSTRUMENT PANEL WIRE
a.
C238342C20
0.594,2.5 0.917,2.719 0.323,0.219 0.25,0.958 0.25,1.24 false 1.75,0.958 1.75,1.24 false 1.302,2.26 0.927,2.073 false 1.792,2.083 1.469,2.25 false 0.958,0.823 0.958,0.51 0.958,0.51 1.115,0.51 false 1.583,2.677 1.885,2.677 false 0.365,0.813 0.667,1.323 0.302,0.51 10 false F 0.635,0.813 1.052,1.208 0.417,0.396 10 false E 1.167,0.813 1.448,1.188 0.281,0.375 10 false D 1.438,0.813 1.635,1.146 0.198,0.333 10 false C 1.979,0.813 2.281,1.438 0.302,0.625 10 false B 2.25,0.813 2.615,1.229 0.365,0.417 10 false A 0.177,1.26 0.438,1.531 0.26,0.271 10 false *1 2.688,0.813 3.052,1.198 0.365,0.385 10 false *2 0.323,1.875 0.646,2.24 0.323,0.365 10 false *a 1.833,2 2.177,2.333 0.344,0.333 10 false P- 1.688,1.25 2.104,1.594 0.417,0.344 10 false *4 0.719,2 1.104,2.313 0.385,0.313 10 false P+ 0.698,2.531 1.063,2.865 0.365,0.333 10 false X1 1.146,0.427 1.521,0.729 0.375,0.302 10 false *3 1.927,2.594 2.26,2.833 0.333,0.24 10 false *b
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag ECU Assembly
*3 No. 2 Instrument Panel Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly)
*b Color: Orange


Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
X1-1 (P+) - Body ground Power switch on (IG) Below 1 V
X1-2 (P-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




b.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X1-1 (P+) - X1-2 (P-) Always Below 1 Ω




c.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X1-1 (P+) - Body ground Always 1 MΩ or higher
X1-2 (P-) - Body ground Always 1 MΩ or higher




d.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector D.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X1-1 (P+) - X1-2 (P-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector D to the original condition.



Result:
Proceed to
OK
NG



OK

NG

REPLACE NO. 2 INSTRUMENT PANEL WIRE